Search ►
Performance Charging Kit
Rick's Electrics High Performance Hot Shot Standard Lead Acid Battery Compatible Charging Kit. This high performance Hot Shot charging kit includes both a new rotor and a standard lead acid battery compatible combination rectifier / regulator which looks like the stock unit and mounts in the same location. The kit will put out approximately 150 watts: 50% over stock. You do NOT need to replace your OE stator unless it tests bad, this kit works with the OE stator. This kit is NOT for use with lithium ion batteries. We sell a charging kit for lithium ion batteries as well.
Starter Motor
Rick's Electrics Starter Motor, Replaces OEM# 31200-300-030 This starter motor features an upgraded 4-Brush permanent magnet design & comes with the battery cable.
Alternator Stator Wire Harness
Alternator Stator Wire Harness, This Harness has the Same 7 Wire Plug as the OEM part and Hooks up Without Alterations. Replaces OEM # 31110-300-154
Stator Sub Harness
Stator Sub Harness, Replaces OEM # 26001-1202
Alternator Stator Wire Harness
Alternator Stator Wire Harness. Connects to the Stator and Field Coil. Replaces OEM # 31110-333-000
Alternator Rotor Ruller
Alternator Rotor Puller
Charging Kit ~ Lithium Ion Version
Rick's Electrics Charging Kit. Kit includes both a high quality stator and lithium-ion friendly rectifier / regulator. The kit will put out approximately 150 watts and power a 55 watt headlight. This kit is Not for use with standard lead acid batteries. The voltage set point is 14V +/- .2. Please contact the manufacturer of your Lithium Ion Battery to ensure our product has the correct set point for their product.
Charging Kit
Rick's Electrics Charging Kit for use with Standard Lead Acid Batteries. Kit includes both a high quality stator and a rectifier / regulator. The kit will put out approximately 150 watts and power a 55 watt headlight. This kit is NOT for use with lithium ion batteries. We sell a charging kit for lithium ion batteries as well.
Tail Light Assembly
Tail Light Assembly. Includes Brake Light Lens, Back Plate, Screws, Gasket, Wires, Connector and Dual Filament Bulb. Replaces OEM # 33700-292-671 / 33700-235-673 / 33701-300-671 / 33701-307-670 Two Bolt Back Mounting Bolt Pattern (Approx 96mm Center to Center), 2 Wires, Ready to Mount to your Bike!
Rotor
Rotor, Replaces OEM# 21007-029
Flywheel Puller
Flywheel Puller M24mm x 1.5mm RH Internal Thread
Cast Aluminum Finned Starter Motor Cover
Cast Aluminum Finned Starter Motor Cover, Made in the USA. Replaces OEM # 31280-300-000 This is a new cover designed and produced like the ones from the 70's that aren't made anymore. This cover is delivered in as-cast condition. As such, Sandblasting, painting, or powder coating will be required if you want a look other then the cast aluminum look. As delivered it is a close match for an original patina engine. Note: Gasket and Hardware Not Included with Cover
LED Charging System Guage
LED Charging system indicator Gauge. Shows Voltage of your alternator rising and falling with RPM and gives a clear indication of your charging systems normal operation and early warning of problems. Gauge is Bright High Quality Chrome plated and clamps onto 7/8" Bars and can be easily wired into any point in the system (before a switched load is best). Can be mounted as shown or to handlebar by clamp (included).
Beehive Chrome Taillight
Beehive Chrome Taillight Universal fender mounting for most applications. For under plate mounting, with upward plate illumination. 12 volt bulb, Gasket for fender mounting and plate bracket included. 6 3/4″ Length, 3″ Width, 4″ Height.
Beehive Black Taillight
Beehive Black Taillight Universal fender mounting for most applications. For under plate mounting, with upward plate illumination. 12 volt bulb, Gasket for fender mounting and plate bracket included. 6 3/4″ Length, 3″ Width, 4″ Height.