Search ►
Tail Light Lens
Tail Light Lens, Replaces OEM# 4NK-84710-00-00 / 4NK-84721-00-00 Length: 6" Width: 4 1/4" (at widest point) Height: 2 3/4" (at tallest point) 3 Mounting Holes
Denso Ignition Contact Points
Contact Points (1pc.) - Replaces OEM # 30202-107-004 / 30202-216-004 / 30202-107-154 These points are for Nippondenso ignitions Only. They are NOT for Hitachi or Kokusan Ignitions. Please check which type you have before ordering. Honda used different ignition systems on some of the same years of bikes.
Muffler Joint Gasket
Muffler Joint Gasket 32mm x 38mm x 30.5mm OEM Ref # 2G2-14714-00 / 31A-14714-00 / 1JK-14714-00 / 3YF-14714-00 Fits: Headpipe
Muffler Joint Gasket
Muffler Joint Gasket 32mm x 38mm x 30.5mm OEM Ref # 2G2-14714-00 / 31A-14714-00 / 1JK-14714-00 / 3YF-14714-00 Fits: Crossover
Muffler Joint Gasket
Muffler Joint Gasket 32mm x 38mm x 30.5mm OEM Ref # 2G2-14714-00 / 31A-14714-00 / 1JK-14714-00 / 3YF-14714-00 Fits: Muffler
Gas Tank Cap
Gas Tank Cap with Keys, Replaces OEM# 17620-KE1-013 / 17620-MN9-013 / 17620-MN9-023 Slightly different then stock - This cap has the vent on the side instead of the top and is a locking type while the stock one was not. Diameter of 3.5"
Rectifier Regulator
Rectifier Regulator 5 Wire (4 Gang Plug With 4 Spades, 1 Wire With Female Bullet Connector) OEM Ref # 32800-43400 / 32800-43X50 / 32800-45220 / 3280-471V0 / 32800-33320 / 32800-49320 / 32800-49X50
Ignition Coil with Cap
Ignition Coil with Cap, Replaces OEM# 30500-VM3-405 / 30510-167-003 / 30500-187-000 / 30500-167-013 / 30500-187-010 / 30500-167-003 / 30500-196-600 / 30500-GC1-000 / 30501-958-000.
Deluxe Carb Rebuild Kit
Deluxe Carburetor Rebuild Kit Jet Sizes Included: Throttle Jet Y187, Pilot Jet #40, Main Jets #122.5 and #125.0, Power Jet #60, Small Main Jet #140, Needle Seat #1.5 Includes Contents Shown
Carb Rebuild Kit
Carb Rebuild Kit - Includes Float Bowl Gasket, Needle, Main Jets #78, Main Jet #112, Metal Plug, D322 Needle, Mixture Screw with Spring, Metal Washer and 4 O-Rings. 1 Kit Needed Per Carb, Order The Quantity you Require
Side Cover Emblem
Cast Metal Side Cover Emblem with 2 Attachment Clips for the rear of the emblem. Note: 2 Emblems Used Per Bike, Order the Quantity you Require Fits: Kawasaki Z1000 A1/A2/A2A (1977-78)
Front Wheel Bearing Retainer Ring Tool
Front Wheel Bearing Retainer Ring Tool. High quality tool for removing and fitting the front wheel bearing retainer ring with 1/2 inch socket bar wrench tool hole. The perfect tool for easier removal and fitting without damaging the special retainer ring.
Front Stock Type Rim
Chrome Front Stock Type Rim, 1.85" Width x 19" x 40 Hole, Overall Actual Width 2.75". These are high quality rims made by D.I.D who originally made the OEM rims. Replaces OEM # 44701-405-771
Radiator Cap
Radiator Cap, Replaces OEM# 19045-MZ3-405 This cap measures 2" in diameter. Some early models of the GL1200 have a different radiator then later models. This cap is designed for a 1.5 inch hole. Check the size of your hole to be sure this will fit before purchasing.
Turn Signal Lamp
Turn Signal Lamp - Chrome 2-Wire Front or Rear
Turn Signal Lens
Turn Signal Lens - Amber - Front or Rear OEM Ref # 23048-1006 / 23048-1022
Turn Signal Stem
Turn Signal Stem - Rear OEM Ref # 23051-1006 14mm thread length, 82mm total length
Valve Cover Gasket
Valve Cover Gasket OEM Ref # 11060-1581 / 11009-1050
Muffler Joint Gasket
Muffler Joint Gasket 35mm x 41mm x 26mm OEM Ref # 11009-1073 / 11009-1634 / 11009-1667 Fits: Muffler
Engine Gasket Set
Complete Engine Gasket Set Includes all Engine Gaskets High Quality - Made In Italy by Athena Athena Product #P400250850950
Passenger Rear Footpegs
Stock Type Passenger Rear Footpeg Set. Replaces OEM # 34028-009 / 92076-024 / 92022-199 / 92043-1464 / 33028-011
Wheel Seal Kit
Rear Wheel Seal Kit 2 Seals 35 x 52 x 7 40 x 62 x 7
Throttle Cable ~ Pull Type
Throttle Cable ~ Pull Type - Replaces OEM# 54012-149A
Steering Stem Nut
Chrome Steering Stem Nut, Hex Nut Size 30mm. Replaces OEM # 90304-415-000 Note: Sold Each, order the quantity your require
Steering Stem Washer
Chrome Steering Stem Washer, Replaces OEM # 90503-283-000 Sold Each, order the quantity you require.
Clutch Lever Switch
Clutch Lever Switch, Replaces OEM# 35330-MB0-003
Engine Oil Seal Kit
Engine Oil Seal Kit - 10 Pc Kit Includes: Camshaft Seal, Clutch Rod Seal, Water Pump Seal, Tachometer Gear Seal, Shift Shaft Seal, Final Driver Gear Seal 1, Final Driver Gear Seal 2, Final Driver Gear Seal 3, Final Driver Gear Seal 4 and Final Shaft Seal.
Stock Style Tachometer
Stock Style Tachometer, Face dial ranges from 0-12000RPM. The ratio of this Tachometer is 4:1 which is the ratio used on stock CB750's. Note: The CB Tachometers slightly changed from year to year, this may not be an exact stock match for your bike but will work great! Housing Size approx 4.6", face 3.9" Check the photo for the design.
Stock Style Shock Absorber Set
Stock Style Shock Absorber Set/2, Replaces OEM# 52400-KB1-601 / 52400-437-003 / 52400-437-711 / 52400-437-770 / 52400-437-712. 395 Eye to Eye, Features a 5 Position Stepped Spring Pre-Load Adjuster Spring Diameter = 53.5mm, Top mounting hole ID = 10mm, Bottom mounting hole ID = 12mm.
Fuel Petcock
Fuel Petcock Assembly, Replaces OEM# 16950-GF6-015 / 16950-163-035 / 16950-GW8-670 / 16950-149-025 / 16950-195-702 / 16950-150-000 / 16950-164-015 / 16950-164-025 / 16950-164-035 / 16950-KE6-830 Fits M14 x 1.0
Fuel Petcock
Fuel Petcock - Replaces OEM # 16950-438-305 Fits M16 x 1.5 Note: These Bikes Listed Came with Either a 14.6mm Nut Thread Diameter (This Petcock) or a 16.9mm Nut Thread Diameter (Part #20-8041). Please Check Your Bikes Thread Diameter to Confirm the Petcock you Require.
Spark Plug Ignition Coil Cap Boot
Spark Plug Ignition Coil Cap Boot, Replaces OEM# 30700-MA0-163 / 30700-MC4-153 / 30700-MA0-153 / 30700-KA2-003 / 30700-HM5-630 / 30700-965-003 / 30700-965-013. Angle = 120 Degrees Height = 40mm or 1.57" Length = 59mm or 2.23" Resistor = 5k OHM
Clutch Plate
Clutch Plate 1 Piece Required OEM Ref # 22201-KAE-000 / 22201-KM4-000 / 22201-KA4-711 / 22201-KA4-712 / 22201-KZ3-730 / 22201-MAE-000 / 22201-MAL-600 / 22201-MR7-000 / 22201-MS6-620 / 22201-MV4-000
Clutch Plate Set (8 Plates)
Clutch Plate Set of 8 Plates. This includes the Fiber Clutch Plates Only (No Steel Plates). Includes 7X Clutch Friction Disk "A" (Replaces OEM# 22201-371-000 / 22201-300-000) and 1X Clutch Friction Disk "B" (Replaces OEM# 22202-392-000 / 22202-371-000).
Clutch Plate Set (10 Plates)
Clutch Plate Set of 10 Plates. This includes the Fiber Clutch Plates Only (No Steel Plates). Includes 7X Clutch Friction Disk "A" (Replaces OEM# 22201-MT8-000), 1X Clutch Friction Disc "B" (Replaces OEM# 22202-MT8-000) and 2X Clutch Friction Disk "C" (Replaces OEM# 22203-MT8-000).
Clutch Plate Set (9 Plates)
Clutch Plate Set of 9 Plates. This includes the Fiber Clutch Plates Only (No Steel Plates). Includes 8X Clutch Friction Disk "A" (Replaces OEM# 22201-ML8-600 , 22201-ML8-000) and 1X Clutch Friction Disc "B" (Replaces OEM# 22202-ML8-600 , 22202-ML8-000)
Carb Rebuild Kit
Carb Rebuild Kit Includes Items Pictured 1 Kit Needed Per Carb Please note that this kit includes a D37 needle, a #110 main jet, and a #40 slow jet. These early bikes had some jetting changes so please check your jet sizes prior to purchase if you need an exact match in size.
Standard Carb Rebuild Kit
Standard Carb Rebuild Kit - Includes Carb Body Seal, Carb Cap O-Ring, Carb Bowl O-Ring, Needle & Seat, Secondary Jets #60, 130 and 140, Needle Jet, Low Speed Jet #35, Air Mixture Screw, Air Mixture Spring, Emulsion Tube, Packing, Spring and 5 Rubber O-Rings. 1 Kit Needed Per Carb, Order The Quantity you Require
Standard Carb Rebuild Kit
Standard Carb Rebuild Kit - Includes Float Bowl Gasket, Needle & Seat 2.0, Main Jet #145, Slow Jet #35, Air Screw with Spring, Mixture Screw, Metal Plug, Metal O-Ring, 4X Cotter Pins, 4X Rubber O-Rings. 1 Kit Needed Per Carb, Order The Quantity you Require
Carburetor Screw Kit
Carburetor Screw Kit. Get a new set of screws to clean up the look of your carbs! Kit Includes: 4X - Drain Screws with O-Rings 1X - 4x8 Screws w Lock Washers 11X- 4x12 Screws w Lock Washers 12X- 4x16 Screws w Lock Washers
Stock Type Gas/Fuel Tank
Stock Type Gas/Fuel Tank. Tank comes in primer grey ready for you to paint your color of choice. Fits: Honda CB400F (1975-76) Supersport Requires a 14mm x 1.0 threaded nut petcock (Our #20-0092 will work), does not accept stock type petcock Does not include gas cap #20-0045, petcock, emblems or any other items.
Rectifier / Regulator ~ Lithium Ion Battery Compatible
Rick's Electric Brand Lithium Ion Battery Compatible Rectifier / Regulator. Replaces OEM# 31600-KV8-681 / 31600-413-008. Designed with a lower voltage set point to work with lithium ion batteries only. Rick's design does not include the black signal wire. This is Not for use with standard lead acid batteries. The voltage set point is 14V +/- .2. Please ensure this set point is correct for your battery before attempting installation.
Rectifier Regulator
Rectifier Regulator 6 Wires - 3 Yellow in One Connector Block + 3 Wires in 4 Space Block OEM Ref # 31600-KV8-681 / 31600-413-008 / 31600-MC9-740
Carburetor Screw Kit
Carburetor Screw Kit. Get a new set of screws to clean up the look of your carbs! Kit Includes: 2X - Drain Screws with O-Rings 8X - 5x12 Screws w Lock Washers 8X - 4x16 Screws w Lock Washers 8X - 6x14 Screws w Lock Washers 5X - 5x16 Screws w Lock Washers 6X - 4x12 Screws w Lock Washers 4X - 4x10 Screws w Lock Washers
Float Needle & Seat
Float Needle & Seat High Quality - Made In Japan OEM Ref # 16030-1016
Rear Stoplight Pedal Brake Light Switch Assembly
Rear Stoplight Pedal Brake Light Switch Assembly, Replaces OEM # 27010-1481
Valve Cover Gasket
Valve Cover Gasket OEM Ref # 11060-1603 / 11009-1274
Front Spoke & Nipple Set
Front Spoke & Nipple Set. 40 Clear Zinc Plated Spokes with 40 Gold Zinc Plated Nipples. Replaces OEM # 41027-085 / 41028-084
Engine Gasket Set
Complete Engine Gasket Set Includes all Engine Gaskets High Quality - Made In Italy by Athena Athena Product # P400250850711
Wheel Seal Kit
Front Wheel Seal Kit 2 Seals 25 x 40 x 8 30 x 42 x 7.5