Honda ►
-
Pick your Honda motorcycle from the list below►
- Honda
Ignition Switch Nut Tool
Ignition Switch Nut Tool, used to loosen and tighten the igntion switch nut properly without causing any damage to the switch.
Clutch Center Nut Removal Tool
Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Inside diameter 24mm, use with 3/8" driver.
Clutch Center Nut Removal Tool ~ Premium
Premium Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Both ends with 1/2 drive extension bar, Diameter 20 x 24.
Valve Adjustment Tool
Valve Adjustment Tool. Use this tool to easily adjust valves.
Carb Float Setting Tool
Carb Float Setting Tool. Use this tool to help set your floats with ease! This pre-set float setting gauge is for the models/years below only. Fits: Honda CB500K (1971-73), CB550K (1974-76), CB550F (1975-77) Supersport
Front Wheel Bearing Retainer Ring Tool
Front Wheel Bearing Retainer Ring Tool. High quality tool for removing and fitting the front wheel bearing retainer ring with 1/2 inch socket bar wrench tool hole. The perfect tool for easier removal and fitting without damaging the special retainer ring.
Rear Wheel Bearing Retainer Ring Tool
Rear Wheel Bearing Retainer Ring Tool. High quality tool for removing and fitting the rear wheel sprocket hub bearing retainer ring with 1/2 inch socket bar wrench tool hole. OR removing and fitting the rear wheel sprocket carrier bearing retainer ring. The perfect tool for easier removal and fitting without damaging the special retainer ring. Removes Rear Wheel Sprocket Carrier Bearing Retainer Ring on the Honda CB750K (1969-78), CB750F (1975-78) Supersport, CB750A (1976-78) Hondamatic Removes Rear Wheel Hub Bearing Retainer Ring on the Honda CB750K (1969-82), CB750A (1976-78) Hondamatic CB750C (1980-82) Custom, CB750L (1979) Limited CB650 (1979-82), CB650C (1980-81) Custom, CB650SC (1982) Nighthawk
Carb Stabilizer Bracket
Carburetor Stabilizer Bracket. Comes with 7mm spacer and 30mm socket head cap screw. These high quality made in Canada stainless steel brackets stabilize the carburetors when the air box is removed. A must have for pods or hard tails!
Carb Float Setting Tool (CB750 1969-76 Models)
Carb Float Setting Tool. Use this tool to help set your floats with ease! This pre-set float setting gauge is for the CB750 1969-76K and 1975-76F Supersport models.
Clymer Service Manual
Clymer CB550/CB650SC Nighthawk Service Manual. Clymer motorcycle repair manuals are written specifically for the do-it-yourself enthusiast. From basic maintenance to troubleshooting to complete overhaul, Clymer manuals provide the information you need. Features Color Wiring Diagrams
Clymer Service Manual
Clymer Service Manual. Clymer motorcycle repair manuals are written specifically for the do-it-yourself enthusiast. From basic maintenance to troubleshooting to complete overhaul, Clymer manuals provide the information you need.
Haynes Workshop Manual
Haynes Workshop Manual Honda GL1100 Gold Wing 1979-1981 1085cc
Haynes Workshop Manual
Haynes Workshop Manual Honda V45/65 Sabre & Magna 1982-1988 (VF700, 750 & 1100 V-Fours) 699cc / 748cc / 1098cc
Chain Adjuster Stopper Set/2
Chain Adjuster Stopper Set/2. High quality steel made in Canada stoppers. These have been discontinued by Honda get these steel upgrades today! Replaces OEM# 52136-405-000 and 52136-ME1-670.
Flywheel Puller
Flywheel Puller M24mm x 1.5mm RH Internal Thread
Alternator Rotor Ruller
Alternator Rotor Puller
Carb Stabilizer Bracket
Carburetor Stabilizer Bracket. These high quality made in Canada stainless steel brackets stabilize the carburetors when the air box is removed. A must have for pods or hard tails!
CB750 Engine Stand
CB750 SOHC Engine Rebuild Stand. Make your engine rebuild a lot easier with this engine stand. Very rigid and easily secured to your work bench using holes found in the base of the stand. Powder coated gloss black for a durable finish. High Quality, Made in the USA.
Carburetor Stabilizer Bracket
Carburetor Stabilizer Bracket. These high quality made in Canada stainless steel brackets stabilize the carburetors when the air box is removed. A must have for pods or hard tails!
Carburetor Adjusting Tool
Carburetor Adjusting Tool. Works with Mikuni or Keihin carbs. 11" long tool with a 8mm hex nut and screwdriver slot adjusting bolt. This combo design allows unlocking of the locknut, adjustments to the balancing screw and re-locking the lock nut in one step.
Screw Extractor Set
Screw Extractor Set 5 Pc Set 1/8", 3/16", 15/64", 5/16", 3/8" Used to remove broken off studs, bolts & screws.
Safety Wire Nut & Metric Bolt Drill Jig Kit
Safety Wire Nut & Metric Bolt Drill Jig Kit. Contains one nut drill jig and one metric bolt jig. Jig set designed for accurate drilling of nuts and bolts for use with safety lock wire. Both jigs can be mounted in a vice for drilling. The nut drill jig allows the safety wire holes to be drilled through the head of bolts or through nuts, across the diagonal easily. Accepts up to a 3.5mm diameter. Metric bolt drill jig provides 6 drill holes for metric sizes 6 X 1.0, 8 X 1.0, 8 X 1.25, 10 X 1.25, 10 X 1.5 and 12 X 1.5 bolts.
Safety Wire Nut & Metric+Imperial Bolt Drill Jig Kit
Safety Wire Nut & Metric+Imperial Bolt Drill Jig Kit. Contains one nut drill jig, one metric bolt jig and one imperial bolt jig. Jig set designed for accurate drilling of nuts and bolts for use with safety lock wire. Both jigs can be mounted in a vice for drilling. The nut drill jig allows the safety wire holes to be drilled through the head of bolts or through nuts, across the diagonal easily. Accepts up to a 3.5mm diameter. Metric bolt drill jig provides 6 drill holes for metric sizes 6 X 1.0, 8 X 1.0, 8 X 1.25, 10 X 1.25, 10 X 1.5 and 12 X 1.5 bolts. Imperial bolt drill jig provides 6 drill holes for imperial sizes 1/4"-20, 5/16"-18, 5/16"-24, 3/8"-16, 3/8"-24 and 7/16"-14 bolts.
Brake Nut Adjust Tool
Brake Nut Adjust Tool, 14mm Size.
Tappet Adjusting Tool Set
Tappet Adjusting Tool Set 4 Piece Set For both 9mm & 10mm valve adjuster screw locknuts. Screwdriver tip & 4mm square tip for valve adjuster screws. For Honda/Yamaha/Suzuki
Fork Cap Socket Tool
19mm Fork Cap Socket Tool, This Tool Is Needed To Loosen Or Remove The Front Fork Cap Bolts On Many Bikes
Tappet Adjusting Tool Set
Tappet Adjusting Tool Set 6 Piece Set Includes T-Socket Wrenches - 8mm, 9mm, 10mm Sizes 3 Adjusters - Slotted Screw, 3mm Square, 4mm Square
Extractor & Drill Set
10 Piece Extractor & Drill Set in a Plastic Case. Set contains 5X extractors (#1 through #5) and 5X mechanic's length cobalt drills. Removes bolts and screws up to 5/8". Cobalt Drill and Screw Extractor Sizes: 5/64", 7/64", 5/32", 1/4", 19/64"
JIS Screw Bit Set
JIS Type 6 Pc. Screw Bit Set with Caribiner Holder. Includes 25mm Bits - PH1, PH2, PH3 and 25mm Torsion Bits (designed to stand up to the rigors of heavy duty impact driving) PH1, PH2, PH3. Most screws used on Japanese motorcycles are NOT phillips but JIS type (Japanese Industry Standard). JIS screws look like a phillips end but have a tiny dot stamped onto the face. It is important to use these correct JIS type bits when working on your motorcycle as phillips bits ARE different and using them are more likely to result in stripping/slipping screws. Get this correct set of JIS bits for your motorcycle today!
3/8" Drive Click Type Torque Wrench Tool
3/8" Drive Window Click Type Torque Wrench Tool with Black Plastic Storage Case. 10-100Ft. Lbs. This click-style torque wrench easily tightens various automotive bolts, from lugs and crankshaft bolts to cylinder heads and engine-mountings. Measures from 10 to 100 foot/pounds in .5 increments.
Tappet Adjuster
Tappet Adjuster Slotted Screw Type
Chrome Bungee Nut Set/2 ~ 6mm x 1.00mm
New chrome pair of grooved Bungee Nuts 6mm x 1.00mm. Can work as a tie down knob, spring anchor or a simple way to attach bungee cords or cargo nets.
Chrome Bungee Nut Set/2 ~ 8mm x 1.25mm
New chrome pair of grooved Bungee Nuts 8mm x 1.25mm. Can work as a tie down knob, spring anchor or a simple way to attach bungee cords or cargo nets.
Chrome Bungee Nut Set/2 ~ 10mm x 1.25mm
New chrome pair of grooved Bungee Nuts 10mm x 1.25mm. Can work as a tie down knob, spring anchor or a simple way to attach bungee cords or cargo nets.
Round Magnetic Parts Dish
Round Stainless Steel Magnetic Parts Dish. Very useful when working with small screws, hardware and parts. 149mm Diameter, 40mm Height.
Performance Tool Spark Plug Crimper Tool
Performance Tool Spark Plug Crimp Tool. Perfect crimping tool for any spark plug wires. Incorporates wire cutter, terminal crimper tool and stripper in one handy tool. Black anodized finish with insulated hand grips. Crimp slot on the end of the tool secures most ignition terminals including "W" type, right angle and "High Tower" terminals. Crimps 7mm to 8.5mm ignition wire. Works with 10 to 22 gauge solderless terminals. High quality made in the USA. Comes with a lifetime warranty through the manufacturer!
Rectangular Magnetic Parts Dish
Rectangular Stainless Steel Magnetic Parts Dish. Very useful when working with small screws, hardware and parts. 9.5" Length, 5.5" Width, 1.1" Height.
Terminal Crimping Tool
Metric Terminal Crimper Tool. Includes sizes 14-16, 14-18, 18-20, 20-24 and 22-24. Professionally Crimps like factory originals. This tool can be used with flag type terminals.
Brush Cleaning Tool
Blue Chain Cleaning Brush/ Gear Cleaner Tool.
Chain Alignment Tool
Chain Alignment Tool. This tool provides an easy way to verify your chain is aligned properly to the front and rear sprockets after rear wheel or chain maintenance. Simply clamp this tool on the rear sprocket with the rod pointing to the front sprocket. With the rod as your guide, make visual alignment then adjust the chain adjusters as needed to correct alignment.
Hex Axle Tool
Universal Hex Axle Tool, Heavy duty Suitable for shop use. Sizes 17, 19, 22, 24. 3/8 Drive on both ends Made with high quality heat treated steel.
Valve Shim Tool
Valve Shim Tool Suz GS550/750/850/1000
Valve Shim Tool
Valve Shim Tool Honda CBX, CB750/900
Clutch Holding Tool
Clutch Holding Tool Adjustable Vise Grip Style Clutch Basket & Sprocket Holder Tool
Piston Ring Tool
Piston Ring Tool with plastic storage case. This tool is designed to prevent ring breakage during cylinder installation. This tool can be easily removed after cylinder is in position. Comes with 4 rings to accept the smallest triple to the largest single cylinder engines. Fits 40-85mm sizes.
Metric Tap & Die Set
Metric Tap & Die Set 39pc Set Includes Pitch Gauge, Die Holder, 2 Tap Wrenches, Screw Driver, Metric Taps: M3 X 0.5 M3 X 0.6 M4 X 0.75 M4 X 0.7 M5 X 0.8 M5 X 0.9 M6 X 1.0 M6 X 0.75 M7 X 0.75 M7 X 1.0 M8 X 1.0 M8 X 1.25 M10 X 1.25 M10 X 1.5 M12 X 1.25 M12 X 1.5 1/8NPT X 27 Includes 17 Dies to Match the 17 Tap Sizes Listed.
Drive Chain Riveter Tool
Drive Chain Riveter Tool Rivets High Strength Rear Drive Chain Rivet Links With Hollow Pin Ends on Many DID Brand Chains.
Replacement Pin For Riveter Tool
Replacement Rivet Pin For Drive Chain Riveter Tool (35-0006)
Steering Bearing Installation Tool
Steering Bearing Installation Tool. Includes one driver and three aluminum adapters. Unique system utilizes specially designed aluminum adaptors to quickly and accurately install nearly any lower bearing. Use with a soft faced hammer.
Chain Press Assembly Tool
Chain Press Assembly Tool Used to Press On Sideplates on rivet or clip rear drive chains