Honda ►
-
Pick your Honda motorcycle from the list below►
- Honda
Carb Rebuild Kit
Deluxe Carburetor Rebuild Kit Includes: Chamber Gasket, Valve Needle, Needle Jet D322, Air Screw, Air Spring, Main Jet #78, Main Jet #115, Needle Jet, Various O-Rings.
Gas/Fuel Tank Cap
OEM Style Gas/Fuel Tank Cap with Rubber Gasket Already Installed, Replaces OEM # 17620-399-010 Note: Does not include a chain attached to this cap.
Performance Charging Kit ~ Lithium Ion Version
Rick's Electrics High Performance Hot Shot Lithium Ion Battery Compatible Charging Kit. This high performance Hot Shot charging kit includes both a new rotor and a lithium-ion battery compatible combination rectifier / regulator which looks like the stock unit and mounts in the same location. The kit will put out approximately 150 watts: 50% over stock. You do NOT need to replace your OE stator unless it tests bad, this kit works with the OE stator. This kit is Not for use with standard lead acid batteries. The voltage set point is 14V +/- .2. Please contact the manufacturer of your Lithium Ion Battery to ensure our product has the correct set point for their product.
Performance Charging Kit
Rick's Electrics High Performance Hot Shot Standard Lead Acid Battery Compatible Charging Kit. This high performance Hot Shot charging kit includes both a new rotor and a standard lead acid battery compatible combination rectifier / regulator which looks like the stock unit and mounts in the same location. The kit will put out approximately 150 watts: 50% over stock. You do NOT need to replace your OE stator unless it tests bad, this kit works with the OE stator. This kit is NOT for use with lithium ion batteries. We sell a charging kit for lithium ion batteries as well.
Starter Motor
Rick's Electrics Starter Motor, Replaces OEM# 31200-300-030 This starter motor features an upgraded 4-Brush permanent magnet design & comes with the battery cable.
Alternator Stator Wire Harness
Alternator Stator Wire Harness, This Harness has the Same 7 Wire Plug as the OEM part and Hooks up Without Alterations. Replaces OEM # 31110-300-154
Clutch Adjuster Bolt
Clutch Adjuster Bolt, Replaces OEM# 22841-425-000
Special Clutch Washer
Special Angled Clutch Washer (16mm), Replaces OEM# 90481-292-000
Alternator Stator Wire Harness
Alternator Stator Wire Harness. Connects to the Stator and Field Coil. Replaces OEM # 31110-333-000
Intake Manifold Assembly "A"
Intake Manifold Assembly "A" - Replaces OEM# 17110-431-010 Full assembly Includes the Metal intake manifold, brand new pliable rubber carb holder, adjustment screw and O-Ring. These integral Intake manifolds have been discontinued for decades, we have had them re-manufactured to keep these Goldwings on the road! 2X "A" Manifolds used per bike, Order the quantity you require
Intake Manifold Assembly "B"
Intake Manifold Assembly "B" - Replaces OEM# 17120-431-010 Full assembly Includes the Metal intake manifold, brand new pliable rubber carb holder, adjustment screw and O-Ring. These integral Intake manifolds have been discontinued for decades, we have had them re-manufactured to keep these Goldwings on the road! 2X "B" Manifolds used per bike, Order the quantity you require
Alternator Rotor Ruller
Alternator Rotor Puller
Charging Kit ~ Lithium Ion Version
Rick's Electrics Charging Kit. Kit includes both a high quality stator and lithium-ion friendly rectifier / regulator. The kit will put out approximately 150 watts and power a 55 watt headlight. This kit is Not for use with standard lead acid batteries. The voltage set point is 14V +/- .2. Please contact the manufacturer of your Lithium Ion Battery to ensure our product has the correct set point for their product.
Charging Kit
Rick's Electrics Charging Kit for use with Standard Lead Acid Batteries. Kit includes both a high quality stator and a rectifier / regulator. The kit will put out approximately 150 watts and power a 55 watt headlight. This kit is NOT for use with lithium ion batteries. We sell a charging kit for lithium ion batteries as well.
Carb Rebuild Kit
Carb Rebuild Kit. Contains: Float Bowl Gasket, Carb Top Gasket, D313 Slide Needle, Main Jet (#105, Stock type for 1977-78F models), Main Jet #110, Stock type for 1978K model), Float Needle, Air Spring, Air Screw Plug, E-Clip, Air Fuel Screw (1978F Type), Air Fuel Screw (1977-78K Type), Needle Jet, Metal Washer, 6 O-Rings. - Made in Japan -
Oil Pump Rebuild Kit
Oil Pump Rebuild Kit Each Kit Contains: Each Kit Contains 91207-580-015 (Oil Seal 10x25x7) x1, 91208-MN1-771 (O-Ring 11x15x3) x1, 91302-200-000 (O-Ring 33.5x3) x1, 94201-30450 (Split Pin 3.0 x45) x1, 15128-371-000 (Oil Passage Gasket) x1, 15229-371-000 (Clutch Oil Pump Gasket) x1.
Matte Black ~ OEM Type Gas/Fuel Tank Cap With Latch Assembly
Matte Black OEM Type Gas/Fuel Tank Cap with Gasket, Hinge Pin (with E-Clip which Allows for easy installation) and Gas/Fuel Tank Cap Latch Assembly, Includes Latch, Return Spring, Latch Mounting Pin and C-Clip. Replaces OEM # 17510-323-310
Carb Holder
Carb Holder with Gasket - Replaces OEM# 16211-283-000 NOTE: This is for One Holder, These Bikes Use 2 Of These So Purchase 2 If Replacing Both Holders. If you require band clamps, this carb holder requires our carb holder clamp #15-0685
Carb Rebuild Kit
Carb Rebuild Kit - Includes Float Bowl Gasket, Needle, Main Jets #78, Main Jet #112, Metal Plug, D322 Needle, Mixture Screw with Spring, Metal Washer and 4 O-Rings. 1 Kit Needed Per Carb, Order The Quantity you Require
Tail Light Assembly
Tail Light Assembly. Includes Brake Light Lens, Back Plate, Screws, Gasket, Wires, Connector and Dual Filament Bulb. Replaces OEM # 33700-292-671 / 33700-235-673 / 33701-300-671 / 33701-307-670 Two Bolt Back Mounting Bolt Pattern (Approx 96mm Center to Center), 2 Wires, Ready to Mount to your Bike!
Carb Rebuild Kit
Carb Rebuild Kit. Contains: Float Bowl Gasket, Float Needle, Main Jet (#118), Jet Holder, Pilot Jet (#35), Air Screw w Spring, Needle Jet Set and 11 Various Rubber O-Rings. Note: Each Kit Rebuilds One Carb, Order the Quantity of Kits you Require
Carb Holder Set
Carb Holder Set (Set of 2 with Gaskets). Replace those old cracked or dried up carb holders with a brand new set! Replaces OEM #'s 16211-369-000 X2 and 16229-369-000 X2 NOTE-If you require band clamps, these carb holders require our 46-49mm diameter clamps part #15-0685 X2.
Carb Rebuild Kit
Deluxe Carburetor Rebuild Kit Includes: 2 Chamber Gaskets, Needle Valve, Needle Jet D267, Needle Jet D268, 2 Air Screws, Air Spring, Main Jets #148, #155 and #158, Slow Jet #50, #60 and #65, 2 Washers, Throttle Screw, Throttle Spring and Various O-Rings.
Standard Carb Rebuild Kit
Standard Carb Rebuild Kit - Includes Float Bowl Gasket, Needle & Seat 2.0, Main Jet #145, Slow Jet #35, Air Screw with Spring, Mixture Screw, Metal Plug, Metal O-Ring, 4X Cotter Pins, 4X Rubber O-Rings. 1 Kit Needed Per Carb, Order The Quantity you Require
Deluxe Carb Rebuild Kit
Deluxe Carb Rebuild Kit - Includes Chamber Gasket, Needle & Seat #1.6, Needle Jet #D513, Air Screw, Air Spring, Main Jet #102, Slow Jet #35, 2 Metal O-RIngs, Metal End Plug, 8X Rubber O-Rings. 1 Kit Needed Per Carb, Order The Quantity you Require
Standard Carb Rebuild Kit
Standard Carburetor Rebuild Kit Includes: 2 Chamber Gaskets, Needle Valve, Needle Jet D267, 2 Air Mixture Screws, 2 Air Springs, Main Jets #155 and #158, Slow Jet #50 and #60, Main Jet Housing, Screw, 5 Metal Washers, 2 Springs and 3 Various O-Rings. Kits Sold Each, Order the Quantity you Require
Standard Carb Rebuild Kit
Standard Carburetor Rebuild Kit Includes: 2 Chamber Gaskets, Needle & Seat #2.4, Needle Jet D268, Air Mixture Screws, Air Spring, Main Jet #148, Slow Jet #65, Main Jet Housing, Screw, 4 Metal Washers, Spring and 3 Various O-Rings. Kit Sold Each, Order the Quantity you Require.
Standard Carb Rebuild Kit
Standard Carburetor Rebuild Kit Includes: 2 Chamber Gaskets, Needle & Seat #2.6, Needle Jet D268, Air Mixture Screw, Air Spring, Main Jet #148, Slow Jet #65, Main Jet Housing, Screw, 5 Metal Washers, Spring and 4 Various O-Rings. Sold Each, Order the Quantity you Require.
Camshaft Holder Seal
1pc. Camshaft holder Rubber Seal (triangular pc. with rounded corners) OEM Ref. # 91311-425-000 - 1 pc. required per Engine
Flywheel Puller
Flywheel Puller M24mm x 1.5mm RH Internal Thread
Clutch Ball Retainer
Clutch Ball Retainer, Replaces OEM# 22860-286-000
Clutch Ball Retainer
Clutch Ball Retainer, Replaces OEM# 22860-300-006
Clutch Ball Retainer
Clutch Ball Retainer, Replaces OEM# 22860-046-000 / 22860-041-000
Cast Aluminum Finned Starter Motor Cover
Cast Aluminum Finned Starter Motor Cover, Made in the USA. Replaces OEM # 31280-300-000 This is a new cover designed and produced like the ones from the 70's that aren't made anymore. This cover is delivered in as-cast condition. As such, Sandblasting, painting, or powder coating will be required if you want a look other then the cast aluminum look. As delivered it is a close match for an original patina engine. Note: Gasket and Hardware Not Included with Cover
Custom Black Gas/Fuel Tank Cap ~ Joker Machine
Joker Machine Brand ~ Custom Black Gas/Fuel Tank Flip Up Billet Cap. Includes Cap with a spring loaded alloy flange, replaceable rubber gasket and alloy screw attachment. Replaces OEM # 17510-323-310 Installs easily onto the tank hinges with an alloy screw (not rivets found on the stock set-up) in minutes. Lightweight design is made from a solid block of 1" thick Billet aluminum. Works with stock style latching mechanisms (Sold Separately). High quality CNC machined cap made in the U.S.A.
Clutch Release Actuator Assembly
Clutch Release Actuator Assembly, Replaces OEM# 22830-371-000 / 22860-300-006 / 22820-371-000 / 22841-300-000 / 91301-426-010
Clutch Release Actuator Assembly
Clutch Release Actuator Assembly, Replaces OEM# 22830-300-000 / 22860-300-006 / 22820-300-000 / 22841-300-000 / 91301-426-010
Muffler Clamp
Muffler Clamp - Universal Fits 1 1/2"
Muffler Clamp
Muffler Clamp - Universal Fits: 1 3/4"
Muffler Clamp
Muffler Clamp - Universal Fits: 1 7/8"
Muffler Reducer
One piece muffler Reducer sleeve. Sleeve is 1" long and reduces universal mufflers with 44-45mm. ID (1.75") down to 38mm. (1.5").
Black Shorty Muffler
Black Shorty Muffler. Super compact design 12" Long, Fits 1 1/2" or 1 3/4" headpipes. Complete with mounting hardware, Friction fit and cannot use clamps. The mounting bracket will hold it in place. Removable glass packed baffle. Mounts on left, or right side. Sold Each
Chrome Shorty Muffler
Chrome Shorty Muffler. Super compact design 12" Long, Fits 1 1/2" or 1 3/4" headpipes. Complete with mounting hardware, Friction fit and cannot use clamps. The mounting bracket will hold it in place. Removable glass packed baffle. Mounts on left, or right side. Sold Each
Flat Black Muffler
Flat Black Muffler 19" Length with a 1 3/4" inlet (1 1/2" and 1 5/8" reducer kit included), Straight through perforated core type non removable baffle. Includes mounting clamp and universal style hanger that is used with slotted channel on backside of muffler for left or right side use. Sold each
Flat Black Tapered Muffler
Flat Black Tapered Muffler Overall length 16.25", Inlet ID: 1-3/4" Or 1-1/2" if you use the included reducer shims. Comes with slide mounting bracket. High quality construction with a non removable mechanical baffle. Can be used on the left or right side. Sold Each
Chrome Reverse Cone Muffler
Chrome Reverse Cone 17" Shorty Muffler High quality construction and finish. Mounting clamp and slide bracket included. Reducer shims included for other fitment sizes. This Muffler will fit head pipes with outer diameters of 1 1/2", 1 5/8" or 1 3/4". Fits on either left or right side. Removable re packable fiberglass baffle. Sold Each
Chrome Reverse Cone Shorty Muffler
Chrome Reverse Cone Shorty Muffler. High quality construction and finish. Straight through perforated core non removable baffle. Overall muffler length 19". 1.75" ID Inlet - Reducer shims included to fit sizes 1 5/8", 1 1/2" and 1 3/8". Mounting clamp and bracket included. Fits on either left or right side. Sold Each
Chrome Upswept Muffler Extension Set
Chrome upswept muffler Extension Set. These are made specifically for Triumphs but they're perfect for adapting any straight mufflers to upswept mufflers. Check the dimensions to see if they'll work on your project. Constructed of 18 gauge chromed steel and slips on stock header pipes to allow mufflers with 1 1/2" to be easily mounted. Adapters allow mounting of "classic" Triumph TR6/T120 63-70 mufflers on Hinkley Bonneville models for a classic look. Sold as a set of 2. Dimensions: Total Length = 7" Short Side = 1 1/2" OD - 1 3/8" ID Long Side = 1 5/8" OD x 1 9/16" ID Angle = 30 Degrees
57mm Exhaust Spring Set
57mm Exhaust Spring Set/2. Used for spring attached mufflers and exhaust pipes. Great for customizing your cafe racer, bobber, tracker or chopper. Works on any style motorcycle.
75mm Exhaust Spring Set
75mm Exhaust Spring Set/2. Used for spring attached mufflers and exhaust pipes. Great for customizing your cafe racer, bobber, tracker or chopper. Works on any style motorcycle.