Honda ► CB1100F ►
-
Here’s our hand-picked list of electrical parts for your Honda CB1100F that match “honda sl125”►
- Honda
Ignition Spark Unit
Aftermarket Ignition Spark Unit for Honda - 2 units required per bike. Replaces Honda OKI or NEC units. Replaces OEM Ref # 30400-MA4-601
Turn Signal Replacement Lens ~ Smoked
Turn Signal Replacement Lens - Smoked - Front Or Rear OEM Ref # 33402-431-782
Tail Light Lens Screws
Tail Light Lens Screws, Set of 4. Replaces OEM # 90147-147-671
Stop Light Switch
Front Stop Light Switch OEM Ref # 35340-MA5-671 / 35340-MM5-600 / 35340-ML7-000
Turn Signal Replacement Lens ~ Amber
Turn Signal Replacement Lens - Amber - Front Or Rear OEM Ref # 33402-431-782
Starter Solenoid Relay
Starter Solenoid Relay with Fuse. Replaces OEM # 35850-MB0-007
Starter Brush Set
Starter Brush Set/2 1Pc Insulated Leads 1Pc Non-Insulated Leads 12mm x 14mm x 6mm For Misuba 2 Brush Starter. OEM Ref # 31201-292-158 / 31201-MG9-004
Fuse Box Assembly
Fuse Box Assembly Complete with 15Amp Fuses, Replaces OEM # 38200-MF9-405
Fuse Box Assembly *Damaged Tabs*
*Damaged Tabs* Fuse Box Assembly Complete with 15Amp Fuses, Replaces OEM# 38200-MF9-405. This Fuse Box Typically has 4 Sets of Attachment Tabs on the back of the assembly used to fasten to the bike. However, several had tabs broken during transit so our loss is your gain! This unit has absolutely nothing wrong with the electrics. The unit your purchasing has damage to some or all of the tabs used to fasten the unit to your bike. Due to where it is attached all tabs should not be needed for installation. You may or may not need to find a solution such as glue/tape etc. to install but it should not pose any problems. As there is a cover over this unit if you use a little duct tape etc. nobody will ever know.
Starter Relay Pigtail / Plug
Starter Relay Pigtail / Plug Connects to our starter relays #24-2004, 24-2157 and 73-0824. Despite wire colors you must confirm wire orientation before hooking up!
Dynatek Dyna 2000 Digital Perfomance Ignition (Ultimate Kit)
Dynatek Dyna 2000 Digital Performance CDI Ignition Ultimate Kit with 2X Dynatek Brand Dual Output Coils and Dynatek Brand High Performance Spark Plug Wires. The Dyna 2000 Digital Performance Ignition represents a breakthrough in motorcycle ignition flexibility. The Dyna 2000 system consists of a state of the art microprocessor controlled ignition module along with an adjustable Dyna dual sensor crank trigger. For the first time you can actually set the ignition timing to what you want to maximize engine performance. A number of different advance curve modes and a broad range rev limiter lets you tailor the ignition to your needs. Up to a 7 horsepower increase! This is a very high quality kit that will increase the performance of your bike! Made in the USA. Features - 5 Different adjustable timing curves, 4 Different retard modes, Fully static time-able with built in LED light (Set the timing accurately without having the engine running), Broad range rev limiter (8,500 to 16,000), Increased horsepower & torque, Digital tach output (smooth & accurate), Increased spark energy, Improved throttle response & easier starting, Easy mounting. Includes the Dyna 2000 unit, complete wiring harness, ignition plate unit with rotor and full instructions, 2X Dynatek coils, Dynatek spark plug wire set. Ignition unit comes with a one year warranty from Dynatek. Note: You must reuse your old factory resistor spark plug caps with this kit, or purchase our #23-3115 X2 and 23-3119 X2 on our site
Dynatek Dyna 2000 Digital Perfomance Ignition (Premium Kit)
Dynatek Dyna 2000 Digital Performance CDI Ignition Premium Kit with 2X Aftermarket Generic 2.5-2.8 Ohm Stock Type Coils and Dynatek Brand High Performance Spark Plug Wires. The Dyna 2000 Digital Performance Ignition represents a breakthrough in motorcycle ignition flexibility. The Dyna 2000 system consists of a state of the art microprocessor controlled ignition module along with an adjustable Dyna dual sensor crank trigger. For the first time you can actually set the ignition timing to what you want to maximize engine performance. A number of different advance curve modes and a broad range rev limiter lets you tailor the ignition to your needs. Up to a 7 horsepower increase! This is a very high quality kit that will increase the performance of your bike! Made in the USA. Features - 5 Different adjustable timing curves, 4 Different retard modes, Fully static time-able with built in LED light (Set the timing accurately without having the engine running), Broad range rev limiter (8,500 to 16,000), Increased horsepower & torque, Digital tach output (smooth & accurate), Increased spark energy, Improved throttle response & easier starting, Easy mounting. Includes the Dyna 2000 unit, complete wiring harness, ignition plate unit with rotor and full instructions, 2X coils, Dynatek spark plug wire set. Ignition unit comes with a one year warranty from Dynatek. Note: You must reuse your old factory resistor spark plug caps with this kit, or purchase our #23-3115 X2 and 23-3119 X2 on our site
Dynatek Dyna 2000 Digital Perfomance Ignition
Dynatek Dyna 2000 Digital Performance CDI Ignition. The Dyna 2000 Digital Performance Ignition represents a breakthrough in motorcycle ignition flexibility. The Dyna 2000 system consists of a state of the art microprocessor controlled ignition module along with an adjustable Dyna dual sensor crank trigger. For the first time you can actually set the ignition timing to what you want to maximize engine performance. A number of different advance curve modes and a broad range rev limiter lets you tailor the ignition to your needs. Up to a 7 horsepower increase! This is a very high quality kit that will increase the performance of your bike! Made in the USA. Features - 5 Different adjustable timing curves, 4 Different retard modes, Fully static time-able with built in LED light (Set the timing accurately without having the engine running), Broad range rev limiter (8,500 to 16,000), Increased horsepower & torque, Digital tach output (smooth & accurate), Increased spark energy, Improved throttle response & easier starting, Easy mounting. Includes the Dyna 2000 unit, complete wiring harness, ignition plate unit with rotor and full instructions. Comes with a one year warranty from Dynatek. Note: You must reuse your old factory resistor spark plug caps with this kit, or purchase our #23-3115 X2 and 23-3119 X2 on our site
Front Reflector
Front Reflector, Replaces OEM# 33742-HB9-641 / 33741-413-003 / 33741-413-013 Amber Reflector with Black Plastic Ring. 2 Segments in the Reflector (Instead of 6 Like the OEM).
Neutral Switch Assembly
Neutral Switch Assembly OEM Ref # 35600-425-023
Replacement Coil Caps & Seals
Replacement Coil tower caps & seals. Fits stock points ignition coils OR our part number 17-6803.
Sub-Wire Harness "A"
Sub-Wire Harness "A", Replaces OEM # 32103-438-660 Plugs into the main wire harness and connects to the ignition coils. This item is not included with our main wire harness's. Please order this item if you require this sub-wire harness "A".
Ignition Coil
Ignition Coil 1.9ohm Primary, 13.4K ohm Secondary Can be Used With Contact Point Ignitions OEM Ref # 30500-422-003 / 30500-422-013 / 30510-MA6-013
Starter Solenoid Switch
Starter Solenoid Switch, Four-gang plug and a 30-Amp fuse with cable attachment.