Honda ► CB1100F ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB1100F with universal parts included►
- Honda
Clutch Damper Repair Kit
Clutch Damper Repair Kit. Includes 7 Clutch Dampers and 7 Screws. The original dampers are often dried and hardened, preventing them from working properly often resulting in a rattling noise. This problem is especially noticeable in neutral at idle and goes away when the clutch cable is pulled in. This lack of proper dampers is hard on your bike internals, replace the old dried up dampers with a new fresh set and keep your bike running smoothly for years to come!
Fuse Box Assembly *Damaged Tabs*
*Damaged Tabs* Fuse Box Assembly Complete with 15Amp Fuses, Replaces OEM# 38200-MF9-405. This Fuse Box Typically has 4 Sets of Attachment Tabs on the back of the assembly used to fasten to the bike. However, several had tabs broken during transit so our loss is your gain! This unit has absolutely nothing wrong with the electrics. The unit your purchasing has damage to some or all of the tabs used to fasten the unit to your bike. Due to where it is attached all tabs should not be needed for installation. You may or may not need to find a solution such as glue/tape etc. to install but it should not pose any problems. As there is a cover over this unit if you use a little duct tape etc. nobody will ever know.
Rear Sprocket ~ 42 Tooth
Rear Sprocket ~ 42 Tooth Replaces OEM# 41200-MZ2-890 / 41200-MG5-670 / 41200-MS2-000 / 41200-MA2-000 / 41200-MC8-670. Stock Size Please Count your sprocket teeth and check your chain length before ordering to ensure this is correct for your bike
Front Reflector
Front Reflector, Replaces OEM# 33742-HB9-641 / 33741-413-003 / 33741-413-013 Amber Reflector with Black Plastic Ring. 2 Segments in the Reflector (Instead of 6 Like the OEM).
Swingarm Dust Seal Cap Set
Swingarm Dust Seal Cap Set of 2, Replaces OEM# 52144-425-831
Handmade Christmas Stocking
HAPPY HOLIDAYS! We are thrilled to be able to offer handmade, one-of-a-kind upcycled Christmas stockings by “Rider Ragsâ€. Featuring a CB750 on the front. They include belt, chain and Honda keychain. Each stocking is individually handmade so there will be variations in denim and belts. Some toes face right and some left. If you have a preference for right/left toe facing make a note in the order comments.
Universal Glas-Pak Insert
Universal Glas-Pak Insert - Fits 1 1/2" Pipes - Glass Pak's Actual Size 1 3/8" Tone down your TT or Drag Pipes
Tire Valve Stem
Tire Valve Stem - Straight Metal Type
Tire Valve Stem
Tire Valve Stem - Straight Rubber Type
Tire Valve Stem
Tire Valve Stem - 90 Degree Metal Type
Tire Valve Stem Caps
Tire Valve Stem Caps - Pk/10 Metal Caps with Core Removal Notch Built In
Tire Valve Stem Caps
Tire Valve Stem Caps - Pk/2 Metal Caps with Core Removal Notch
Tire Fill Valve
Ninety Degree Tire Fill Valve
Rivet Link
Cam Chain Rivet Link Stepped Parallel Plate Fits BF05T Cam Chains
Rivet Link
Cam Chain Rivet Link Stepped Parallel Plate Fits 219FTSS Cam Chains
Rivet Link
Cam Chain Rivet Link Stepped Peanut Plate Fits 219T Cam Chains
Clip Link
Cam Chain Clip Link Peanut Shape Fits 25H Cam Chains
Cam Chain Rivet Link
Cam Chain Rivet Link Peanut Shape Fits BS05MH TSUBAKI
Cam Chain Rivet Link
Cam Chain Rivet Link Peanut Shape Fits BF05M TSUBAKI
Cam Chain Rivet Link
Cam Chain Rivet Link Fits 82RH2015
Custom Micro Push Button/Kill Switch
Custom Micro Push Button/Kill Switch. High quality chrome switch designed to clean up the appearance of your bike while allowing the use of a switch. Works great as a hidden start/kill or horn button. Includes a contoured washer which allows for installations on round surfaces such as handlebars or frames. Switch Size 14mm x 12mm with 2X 20" wires.
Push/Pull Style Throttle Assembly
Custom Dual Cable Style (Push/Pull) Throttle Assembly for 7/8" bars. Satin Black Die-Cast aluminum housing with a nylon throttle tube. Housing is threaded to accept Honda push/pull throttle cables. Opens carbs up to 38mm. Allen key included for assembly. Pull cable thread size is M10 x 1.25mm, Push cable thread size is M12 x 1.00mm. Throttle is 6" total in length.
Heated Grips
Heated Grip Set/2 for 7/8" HANDLEBARS ONLY. Warms up when the engine is running. Features a high/low/off switch. Easy to use relay protected sealed controls. Rubber resistant to low temperatures and resists cracking. Easy install with no gluing needed. 130mm Length
Classic Coke Bottle Grips
Classic Coke Bottle Grip Set - Black - 130mm Length - Closed End - for 7/8" bars.
Grips
Rubber Cushion Grip Set Gran Tourismo - Dual Wall - Black With Closed Ends For 1" Bars, 130mm Length
Grips
Roadhawk Grip Set Chrome Plate Ends With Roadhawk Design 5" Inside Length x 7/8"
Grips
Cushion Grip Set Straight Design With Chrome Ends 5 3/4" Inside Length x 7/8" 150mm Length
Grips
Sportbike Gel Grip Set Closed End Type 5" Inside Length x 7/8" 135mm Length
Grips
Cushion Grip Set Straight Design With Chrome Ends 5 3/8" Inside Length x 7/8" 140mm Length
Grips
Foam Grip Set Black Plastic End Inserts 5" Inside Length x 7/8" 130mm Length
Grips
Superbike Grip Set Short Style With End Caps Black - 125mm Length
Grips
Superbike Grip Set Short Style With End Caps Red - 125mm Length
Grips
Superbike Grip Set Short Style With End Caps ***Blue*** - 125mm Length
Grips
Ribbed Grip Set Yamaha OEM Type - Black With Closed Ends 5" Inside Length x 7/8" 120mm Length
Amal Barrel Style Grips
Glossy Black Amal Barrel Style Grip Set - 115mm Long - Closed Ends - for 7/8" bars
Grips
Superbike Grip Set Touring Style With End Caps Black - 135mm Length
Retro Grips ~ Dark Brown
Retro Grips - Dark Brown - Closed end type for 7/8" bars. 124mm Length
Grips
Black Moto Cross Performance Grip Set 115mm Length
Grips
Red Moto Cross Performance Grip Set 115mm Length
Grips
Blue Moto Cross Performance Grip Set 115mm Length
Amal Barrel Style Grips
Glossy Black Amal Barrel Style Grip Set - 115mm Long - Closed Ends - for 1" bars
Grips
Yellow Moto Cross Performance Grip Set 115mm Length
Classic Coke Bottle Grips
Classic Coke Bottle Grip Set - Black - 130mm Length - Closed End - for 1" bars.
Grips
Rubber Cushion Grip Set Gran Tourisimo - Black With Closed Ends 5" Inside Length x 7/8" 130mm Length
Universal Grips w Throttle Sleeve ~ Black
Universal Grips with Throttle Sleeve Attached (Includes 3 Different Throttle Sleeve Ends) ~ Black Set - for 7/8" bars. 120mm Length
Universal Grips w Throttle Sleeve ~ Silver
Universal Grips with Throttle Sleeve Attached (Includes 3 Different Throttle Sleeve Ends) ~ Silver Set - for 7/8" bars. 120mm Length
Black Single Cable Pull Throttle Assembly 1"
Black Single Cable Pull Throttle Assembly For 1" Bars Jackhammer Style 140mm Length Grips Features Tension Adjuster and Built in Cable Adjustment High Quality Black Powder Coated Aluminum Housing and Aluminum Throttle Tube
Black Dual Pull Cable Throttle Assembly 7/8"
Black Dual Pull Cable Throttle Assembly For 7/8" Bars Jackhammer Style 140mm Length Grips Features Tension Adjuster and Built in Cable Adjustment High Quality Black Powder Coated Aluminum Housing and Aluminum Throttle Tube
Black Aluminum Handlebar End Plug Set
Black Anodized Aluminum Handlebar End Plug Set with Allen Key for Install. These Reduce handlebar vibration, while adding a nice touch. Can be installed in seconds. Just pop them in to the open end of your grips and tighten the bolt with the included allen key. These will fit into any 7/8" handlebars with open ends