Honda ► CB1100F ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB1100F with universal parts included that match “petcock adapter plates”►
- Honda
Fuel Petcock
Fuel Petcock - OEM Ref. # 16950-461-751 Fits M20 x 1.0 Note: Please Check that the Size Listed Above is Correct for your Bike before ordering
DOHC Screw Set
71PC DOHC Screw Set, Includes Front Stay Plate Screws (8), CV Cap Screws (8), Throttle Cable Bracket Screw (1), Rear Stay Plate Screws (8), Vacuum Petcock Screws (6), Bowl Screws (12), Accelerator Pump Cover Screws (3), Air Cutoff Screws (8), Choke Cable Clamp Screw (1), Throttle Plate Screws (8) and Choke Plate Screws (8).
Clutch Plate
Clutch Plate 1 Piece Required OEM Ref # 22202-425-000 / 22202-MT8-000
Clutch Plate
Clutch Plate 7 Pieces Required OEM Ref # 22201-425-000 / 22201-MN5-020 / 22201-MT8-000 / 13088-030
Steel Clutch Plate "B" ~ Riveted Plate
Steel Clutch Drive Plate "B" - OEM Ref # 22322-425-000 This is the thick double steel plate with rivets in it. It is an essential part of any clutch rebuild as the rivets are known to wear over time. 1PC Required per Bike
Steel Clutch Plate
Steel Clutch Plate 6 Pieces Required
Rotor Brush Plate Holder
Rotor Brush Plate Holder for Alternators, Replaces OEM# 31126-422-015 / 31126-422-005.
Center Stand Spring Plate
Center Stand Spring Plate, This is the Plate the Center Stand Spring Attaches to. Replaces OEM # 50523-425-000
Clutch Tab Washer
Clutch Tab Washer, 16mm Size, Replaces OEM # 90431-292-000
Clutch Damper Repair Kit
Clutch Damper Repair Kit. Includes 7 Clutch Dampers and 7 Screws. The original dampers are often dried and hardened, preventing them from working properly often resulting in a rattling noise. This problem is especially noticeable in neutral at idle and goes away when the clutch cable is pulled in. This lack of proper dampers is hard on your bike internals, replace the old dried up dampers with a new fresh set and keep your bike running smoothly for years to come!
Special Clutch Washer
Special Angled Clutch Washer (16mm), Replaces OEM# 90481-292-000
Clutch Spring Bolt Set
Clutch Spring Bolt Set of 6. Replaces OEM # 95725-06025-00 X6.
Dynatek Dyna 2000 Digital Perfomance Ignition
Dynatek Dyna 2000 Digital Performance CDI Ignition. The Dyna 2000 Digital Performance Ignition represents a breakthrough in motorcycle ignition flexibility. The Dyna 2000 system consists of a state of the art microprocessor controlled ignition module along with an adjustable Dyna dual sensor crank trigger. For the first time you can actually set the ignition timing to what you want to maximize engine performance. A number of different advance curve modes and a broad range rev limiter lets you tailor the ignition to your needs. Up to a 7 horsepower increase! This is a very high quality kit that will increase the performance of your bike! Made in the USA. Features - 5 Different adjustable timing curves, 4 Different retard modes, Fully static time-able with built in LED light (Set the timing accurately without having the engine running), Broad range rev limiter (8,500 to 16,000), Increased horsepower & torque, Digital tach output (smooth & accurate), Increased spark energy, Improved throttle response & easier starting, Easy mounting. Includes the Dyna 2000 unit, complete wiring harness, ignition plate unit with rotor and full instructions. Comes with a one year warranty from Dynatek. Note: You must reuse your old factory resistor spark plug caps with this kit, or purchase our #23-3115 X2 and 23-3119 X2 on our site
Dynatek Dyna 2000 Digital Perfomance Ignition (Ultimate Kit)
Dynatek Dyna 2000 Digital Performance CDI Ignition Ultimate Kit with 2X Dynatek Brand Dual Output Coils and Dynatek Brand High Performance Spark Plug Wires. The Dyna 2000 Digital Performance Ignition represents a breakthrough in motorcycle ignition flexibility. The Dyna 2000 system consists of a state of the art microprocessor controlled ignition module along with an adjustable Dyna dual sensor crank trigger. For the first time you can actually set the ignition timing to what you want to maximize engine performance. A number of different advance curve modes and a broad range rev limiter lets you tailor the ignition to your needs. Up to a 7 horsepower increase! This is a very high quality kit that will increase the performance of your bike! Made in the USA. Features - 5 Different adjustable timing curves, 4 Different retard modes, Fully static time-able with built in LED light (Set the timing accurately without having the engine running), Broad range rev limiter (8,500 to 16,000), Increased horsepower & torque, Digital tach output (smooth & accurate), Increased spark energy, Improved throttle response & easier starting, Easy mounting. Includes the Dyna 2000 unit, complete wiring harness, ignition plate unit with rotor and full instructions, 2X Dynatek coils, Dynatek spark plug wire set. Ignition unit comes with a one year warranty from Dynatek. Note: You must reuse your old factory resistor spark plug caps with this kit, or purchase our #23-3115 X2 and 23-3119 X2 on our site
Dynatek Dyna 2000 Digital Perfomance Ignition (Premium Kit)
Dynatek Dyna 2000 Digital Performance CDI Ignition Premium Kit with 2X Aftermarket Generic 2.5-2.8 Ohm Stock Type Coils and Dynatek Brand High Performance Spark Plug Wires. The Dyna 2000 Digital Performance Ignition represents a breakthrough in motorcycle ignition flexibility. The Dyna 2000 system consists of a state of the art microprocessor controlled ignition module along with an adjustable Dyna dual sensor crank trigger. For the first time you can actually set the ignition timing to what you want to maximize engine performance. A number of different advance curve modes and a broad range rev limiter lets you tailor the ignition to your needs. Up to a 7 horsepower increase! This is a very high quality kit that will increase the performance of your bike! Made in the USA. Features - 5 Different adjustable timing curves, 4 Different retard modes, Fully static time-able with built in LED light (Set the timing accurately without having the engine running), Broad range rev limiter (8,500 to 16,000), Increased horsepower & torque, Digital tach output (smooth & accurate), Increased spark energy, Improved throttle response & easier starting, Easy mounting. Includes the Dyna 2000 unit, complete wiring harness, ignition plate unit with rotor and full instructions, 2X coils, Dynatek spark plug wire set. Ignition unit comes with a one year warranty from Dynatek. Note: You must reuse your old factory resistor spark plug caps with this kit, or purchase our #23-3115 X2 and 23-3119 X2 on our site
Universal Fuel Petcock Adaptor Plate
Universal Fuel Petcock Adaptor Plate (34mm) 3/8" NPT Adaptor Plate With 34mm Center-Center Holes
Universal Fuel Petcock Adaptor Plate
Universal Fuel Petcock Adaptor Plate (44mm) 3/8" NPT Adaptor Plate With 44mm Center-Center Holes
Universal Fuel Petcock Adaptor Plate
Universal Fuel Petcock Adaptor Plate (46mm) 3/8" NPT Adaptor Plate With 46mm Center-Center Holes
Universal Fuel Petcock
Universal Fuel Petcock On/Off/Reserve Positions One straight Outlet Fitting, Two ninety degree outlet fittings & One outlet blockoff plug included. Direct fit to 3/8" NPT (Female Thread) in tank or choose adaptor plate or Nut as required.
Petcock Outlet Fitting
Replacement Outlet Fitting Fits Our Universal Petcock 20-0100
Universal Fuel Petcock Adaptor Nut
Universal Fuel Petcock Adaptor Nut (22mm) - Fits M22 x 1.0 7/8" or 22mm Dia Thread Male Tank Bung to 3/8" NPT
Universal Fuel Petcock Adaptor Nut
Universal Fuel Petcock Adaptor Nut (24mm) - Fits M24 x 1.0 15/16" or 24mm Dia Thread Male Tank Bung to 3/8" NPT
Cast Aluminum Black Headlight Bracket Set
Cast Aluminum Black Headlamp Mounting Bracket Set. Sold with adapters to fit 35mm, 39mm and 41mm fork tube outer diameters.
Valve Spring Compressor
Valve Spring Compressor Kit in a Plastic Storage Case. Includes adapter sizes 16mm, 19mm, 23mm, 25mm and 30mm.
Steering Bearing Installation Tool
Steering Bearing Installation Tool. Includes one driver and three aluminum adapters. Unique system utilizes specially designed aluminum adaptors to quickly and accurately install nearly any lower bearing. Use with a soft faced hammer.