Honda ► CB350 ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB350 with universal parts included that match “screws nuts bolts tools”►
- Honda
Clutch Center Nut Removal Tool ~ Premium
Premium Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Both ends with 1/2 drive extension bar, Diameter 20 x 24.
Side Stand Pivot Bolt & Nut Set
Side Stand Pivot Bolt & Nut Set, This is the Set Used to Fasten the Side Stand in Place. Replaces OEM # 90108-283-000 (Bolt) and 94002-10000-0S (Nut).
Turn Signal Pinch Bolt Set
Turn Signal Pinch Bolt Set. Includes 2X Chrome Bolts, 2X Hex Nuts and 4X Flat Washers. This set is used to clamp the turn signal onto the stem. Some models originally had a 25mm long bolt but these will interchange. This set includes hardware for 2 turn signals. If you need enough for all 4 signals please purchase 2 sets.
Drive Chain Adjuster
Drive Chain Adjuster with Nut and Bolt, Replaces OEM# 95014-17000 / 40543-286-000. If you require 2 adjusters purchase 2 of this part.
Float Bowl Drain Screw
Float Bowl Drain Screw w O-Ring. Note: We sell these each, order the quantity you require
Side Cover Emblem Fixing Nut Pk/2
Side Cover Emblem Fixing Nut (3mm) Pk/2, Used to Attach the Side Cover Emblems. Replaces OEM # 90313-567-000 Check your bike to see the quantity you require
Air Screw Needle O-Ring
Air Screw Needle O-Ring. 2.8mm x 1.2mm. Note: sold each, order the quantity you require
Tail Light Assembly
Tail Light Assembly. Includes Brake Light Lens, Back Plate, Screws, Gasket, Wires, Connector and Dual Filament Bulb. Replaces OEM # 33700-292-671 / 33700-235-673 / 33701-300-671 / 33701-307-670 Two Bolt Back Mounting Bolt Pattern (Approx 96mm Center to Center), 2 Wires, Ready to Mount to your Bike!
Joker Machine Magnetic Oil Drain Plug
Joker Machine Magnetic Oil Drain Plug with O-Ring, Replaces OEM# 90013-312-000. High quality made from 6061 billet aluminum. High power rare earth neodymium-iron boron magnet pressed into the body that exceptionally grabs steel debris from your tank and motor. M33.7 - 1.5mm thread pitch. Installs with a 19mm socket. - 45mm outside diameter and 19mm off the case.
Special Oil Filter Rotor Washer
Special Angled Oil Filter Rotor Washer (16mm), Replaces OEM# 90481-292-000
Front Sprocket Lock Plate Set
Front Sprocket Lock Plate with 2 Lock Plate Bolts. It's Always good to replace these when installing a new front sprocket. Replaces OEM # 23811-292-000 (Plate) and OEM # 92101-06016-0A (Bolts) X2.
Carburetor Adjusting Tool
Carburetor Adjusting Tool. Works with Mikuni or Keihin carbs. 11" long tool with a 8mm hex nut and screwdriver slot adjusting bolt. This combo design allows unlocking of the locknut, adjustments to the balancing screw and re-locking the lock nut in one step.
Screw Extractor Set
Screw Extractor Set 5 Pc Set 1/8", 3/16", 15/64", 5/16", 3/8" Used to remove broken off studs, bolts & screws.
Safety Wire Nut & Metric Bolt Drill Jig Kit
Safety Wire Nut & Metric Bolt Drill Jig Kit. Contains one nut drill jig and one metric bolt jig. Jig set designed for accurate drilling of nuts and bolts for use with safety lock wire. Both jigs can be mounted in a vice for drilling. The nut drill jig allows the safety wire holes to be drilled through the head of bolts or through nuts, across the diagonal easily. Accepts up to a 3.5mm diameter. Metric bolt drill jig provides 6 drill holes for metric sizes 6 X 1.0, 8 X 1.0, 8 X 1.25, 10 X 1.25, 10 X 1.5 and 12 X 1.5 bolts.
Safety Wire Nut & Metric+Imperial Bolt Drill Jig Kit
Safety Wire Nut & Metric+Imperial Bolt Drill Jig Kit. Contains one nut drill jig, one metric bolt jig and one imperial bolt jig. Jig set designed for accurate drilling of nuts and bolts for use with safety lock wire. Both jigs can be mounted in a vice for drilling. The nut drill jig allows the safety wire holes to be drilled through the head of bolts or through nuts, across the diagonal easily. Accepts up to a 3.5mm diameter. Metric bolt drill jig provides 6 drill holes for metric sizes 6 X 1.0, 8 X 1.0, 8 X 1.25, 10 X 1.25, 10 X 1.5 and 12 X 1.5 bolts. Imperial bolt drill jig provides 6 drill holes for imperial sizes 1/4"-20, 5/16"-18, 5/16"-24, 3/8"-16, 3/8"-24 and 7/16"-14 bolts.
Tappet Adjusting Tool Set
Tappet Adjusting Tool Set 4 Piece Set For both 9mm & 10mm valve adjuster screw locknuts. Screwdriver tip & 4mm square tip for valve adjuster screws. For Honda/Yamaha/Suzuki
Fork Cap Socket Tool
19mm Fork Cap Socket Tool, This Tool Is Needed To Loosen Or Remove The Front Fork Cap Bolts On Many Bikes
Tappet Adjusting Tool Set
Tappet Adjusting Tool Set 6 Piece Set Includes T-Socket Wrenches - 8mm, 9mm, 10mm Sizes 3 Adjusters - Slotted Screw, 3mm Square, 4mm Square
Gold Bullet Shaped License Plate Bolt
Gold Colored Bullet Shaped Bolt with Nut and Washer. These bullet shaped bolts are made from cast aluminum. The Bullet is 3/4" tall with a 3/4" round base. The 3/4" long x 1/4"-20 threaded stud is removable. There are many uses for these bolts including license plate holder bolts and more! They can be mounted to about anything using 1/4"-20 bolts or screws to hold the bullets in place. Note: Sold Each, Order the Quantity you Require
Chrome Bullet Shaped License Plate Bolt
Chrome Bullet Shaped Bolt with Nut and Washer. These bullet shaped bolts are made from cast aluminum. The Bullet is 3/4" tall with a 3/4" round base. The 3/4" long x 1/4"-20 threaded stud is removable. There are many uses for these bolts including license plate holder bolts and more! They can be mounted to about anything using 1/4"-20 bolts or screws to hold the bullets in place. Note: Sold Each, Order the Quantity you Require
Extractor & Drill Set
10 Piece Extractor & Drill Set in a Plastic Case. Set contains 5X extractors (#1 through #5) and 5X mechanic's length cobalt drills. Removes bolts and screws up to 5/8". Cobalt Drill and Screw Extractor Sizes: 5/64", 7/64", 5/32", 1/4", 19/64"
JIS Screw Bit Set
JIS Type 6 Pc. Screw Bit Set with Caribiner Holder. Includes 25mm Bits - PH1, PH2, PH3 and 25mm Torsion Bits (designed to stand up to the rigors of heavy duty impact driving) PH1, PH2, PH3. Most screws used on Japanese motorcycles are NOT phillips but JIS type (Japanese Industry Standard). JIS screws look like a phillips end but have a tiny dot stamped onto the face. It is important to use these correct JIS type bits when working on your motorcycle as phillips bits ARE different and using them are more likely to result in stripping/slipping screws. Get this correct set of JIS bits for your motorcycle today!
3/8" Drive Click Type Torque Wrench Tool
3/8" Drive Window Click Type Torque Wrench Tool with Black Plastic Storage Case. 10-100Ft. Lbs. This click-style torque wrench easily tightens various automotive bolts, from lugs and crankshaft bolts to cylinder heads and engine-mountings. Measures from 10 to 100 foot/pounds in .5 increments.