Honda ► CB350F ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB350F with universal parts included►
- Honda
Fork Seals
Fork Seals Set/2 33 X 46 X 10.5/11
Fork Seals
Fork Seals Set/2 33 X 46 X 11
Master Cylinder Reservoir Cap
Master Cylinder Cap with Plastic O-Ring. Replaces OEM # 45513-341-771 This style of master cylinder cap was discontinued long ago by Honda. We have had these produced again to keep your bike looking sharp. Spruce up your Master Cylinder with one of these great looking master cylinder caps!
Front Brake Caliper Piston
Front Brake Caliper Piston (1) - 38.15mm Diameter x 34mm Height - Replaces OEM # 45107-323-020. Please note: the side with the 2mm outer lip faces the brake pad during install.
Master Cylinder Reservoir Cap Plastic O-Ring
Master Cylinder Reservoir Cap Plastic O-Ring, Replaces OEM # 45521-MJ6-006
Reservoir Cap & Diaphragm
Reservoir Cap & Diaphragm Round Thread On Type OEM Ref # 43515-MJ6-006 / 45520-300-000
Speedo Gear Plug
Speedo Gear Plug - Plug 15mm Outer Diameter, 22mm Long. This Plug is Great for Keeping your Original Speedo Drive Gear Clean.
Rear Brake Shoes
Rear Brake Shoes Pk/2 Diameter: 159mm Width: 30mm OEM Ref # 43120-KG4-006
Front Brake Pads
Front Brake Pads Pk/2 OEM Ref # 45105-390-006A
Brake Caliper Bleed Screw Rubber Cap (Stock Type)
Stock Type Brake Caliper Bleed Screw Rubber Cap. These are the Same Design Rubber Caps as the Originals from the Factory. Replaces OEM # 45110-300-003 / 45224-579-013
Clutch Spring Set
Clutch Spring Set, 4 Pc. Set.
Clutch Plate
Clutch Plate 6 Pieces Required OEM Ref # 22201-333-010 / 22201-377-000 / 22201-ML4-610
Carb Holder Set
Carb Holder Set (Set of 4) with O-Rings to Seal the Manifolds to the Cylinder Block - Replaces OEM# 16212-333-030 X2 and 16213-333-030 X2
Float Needle & Seat
Float Needle & Seat High Quality - Made In Japan OEM Ref # 16011-329-004
Carb Rebuild Kit
Carb Rebuild Kit Includes Items Pictured High Quality - Made In Japan 1 Kit Needed Per Carb
Carb Diaphragm Rubber
Carburetor Top Diaphragm Rubber. Outer dimension 72mm - Inner dimension 25mm. Replaces the diaphragm rubber on Honda OEM# 16022-287-004 / 16022-287-014 / 16022-287-024. Note: When installing be sure to line up the rubber tab on the diaphragm so the slide is in it's proper orientation. Sold Each, order the quantity you require.
Float Bowl Drain Screw
Float Bowl Drain Screw w O-Ring. Note: We sell these each, order the quantity you require
Side Cover Emblem
Side Cover Emblem with Attachment Clips, Replaces OEM# 87128-333-000 Sold Each, Order the Quantity you Require
Trip Meter Knob Rubber Grommet
Day Trip Meter Knob Rubber Grommet. These grommets are often dried out and ripped, get a new one today!
Carburetor Screw Kit
Carburetor Screw Kit. Get a new set of screws to clean up the look of your carbs! Kit Includes: 4X - Drain Screws with O-Rings 16X- 4x12 Screws w Lock Washers 8X - 5x16 Screws w Lock Washers 2X - 6x14 Screws w Lock Washers
Brake Hose Rubber Grommet
Brake Hose Rubber Grommet, This is the Rubber Grommet that Attaches to the Brake Hose. Replaces OEM # 45146-300-000
Starter Motor Terminal Rubber Boot
Starter Motor Terminal (Cover) Rubber Boot. Replaces OEM # 32411-230-000
Shock Absorber Joint Rubber Set/2
Shock Absorber Joint Rubber Set/2. Replaces OEM # 52484-292-000
Primary Chain
OEM Quality Primary Chain, 50 Link. Replaces OEM # 92057-1011 / 23131-426-003 / 23131-323-003
Front Wheel Spoke Set
Front Spoke Set with Nipples - 36 Spokes with 36 Nipples. Note: Spokes are Silver in Color and Nipples are Gold in Color. For Stock 18" Front Type Rims Only
Rear Wheel Spoke Set
Rear Spoke Set with Nipples - 36 Spokes with 36 Nipples. Note: Spokes are Silver in Color and Nipples are Gold in Color. For Stock 18" Rear Type Rims Only
CB350F 1973 Speedo & Tach Face Decal Set ~ MPH
Speedometer & Tachometer Face Decal (Sticker) Set ~ MPH Type. These decals must be applied over the original gauge face to illuminate. Disassembly of speedometer and tachometer is required. Mounting holes are pre cut to simplify application. Openings for odometer & tripmeter must be cut out after application. Removal of original information printed on OEM plastic face is required prior to application of these decals. All decals are "printed" in North America on the highest quality materials.
CB350F 1972-73 Gas Tank Decal Set ~ Candy Bacchus Olive
Honda CB350F (1972-73) Supersport Gas Tank Decal (Sticker) Set for the Candy Bacchus Olive Model. These reproductions will add the finishing touch to your restoration. These decals are no longer available from the manufacturer. All decals are "printed" on the highest quality materials from companies such as 3M and Avery. All decals have a protective coating to resist scratching and to protect colors from UV rays. These decals are adhesive backed for simple application.
CB350F 1972-73 Gas Tank Decal Set ~ Flake Matador Red
Honda CB350F (1972-73) Supersport Gas Tank Decal (Sticker) Set for the Flake Matador Red Model. These reproductions will add the finishing touch to your restoration. These decals are no longer available from the manufacturer. All decals are "printed" on the highest quality materials from companies such as 3M and Avery. All decals have a protective coating to resist scratching and to protect colors from UV rays. These decals are adhesive backed for simple application.
Master Cylinder Damper Set
Master Cylinder Damper Set. Includes Brake Master Cylinder Rubber Damper, Plate and Washer. This Set is often missing and is used to reduce vibration to the master cylinder lever.
Brake Rod Joint Pin w Cotter Pin
Brake Rod Joint Pin with Cotter Pin, Replaces OEM # 95015-52000 (Joint Pin) and OEM # 94201-16250 (Cotter Pin).
Brake Rod Adjusting Nut
Brake Rod Adjusting Nut, Replaces OEM # 95015-42000
Grease Fitting Nipple (Pk/2)
Grease Fitting Nipple A .45 (Pk/2). Replaces OEM # 96201-30001
Side Cover Emblem Fixing Nut Pk/2
Side Cover Emblem Fixing Nut (3mm) Pk/2, Used to Attach the Side Cover Emblems. Replaces OEM # 90313-567-000 Check your bike to see the quantity you require
Shift Shaft Seal
Shift Shaft Seal - 14 x 28 x 7 - Replaces OEM # 91206-286-013
Front Brake Caliper Bolt & Washer Set
Front Brake Caliper Bolt & Washer Set. Set includes 2 Bolts and 2 Washers. Replaces OEM # 90165-323-000
Handlebar Brake Lever Pivot Bolt & Nut Set
Brake Lever Pivot Bolt & Nut. This is the Set that Fastens the Brake Lever in Place. Includes One Bolt with One Nut. Replaces OEM # 90114-300-000
Carb Bolt Kit
Carburetor Bolt and Washer 40 Piece Kit. This is a Complete Bolt Kit for All 4 Carburetors.
Engine Cover Hardware Set
Engine Cover 34 Piece Hardware Set, Includes the Bolts/Screws for the Engine Case Side Covers, Alternator Cover, Points Cover and Tach Cover.
Rear Wheel Bearing Retainer
Rear Wheel Bearing Retainer - Brake Disc Side - Replaces OEM# 41231-286-000
Seat Lock Bar Assembly
Seat Lock Bar Assembly, Replaces OEM# 77220-340-003 / 77220-340-011
Custom Brake Rod Adjuster Knob ~ Joker Machine
Joker Machine Brand ~ Custom Brake Rod Adjuster Knob, Replaces OEM # 95015-42000 Gives your bike a great custom look while refining the quality of your brake adjuster knob! Makes for super easy brake adjustments due to the choice of a knurled outside knob and a hex nut feature all in one. High quality CNC machined part, made in the U.S.A.
Custom Rear Brake Stopper Arm Strap ~ Joker Machine
Joker Machine Brand ~ Custom Rear Brake Stopper Arm Strap, Replaces OEM # 43431-286-010 / 43431-340-000 This strap is lightweight, identical length to the stock strap and really gives your bike a great custom look! High quality part CNC machined in the U.S.A.
Custom Performance Magnetic Oil Drain Plug ~ Joker Machine
Joker Machine Brand ~ Custom Performance Magnetic Oil Drain Plug - 12mm. Dia x M1.5 - OEM Ref # 92800-12000 Plug features an extended length HIGH POWER "rare earth" Neodymium-Iron-Boron Magnet pressed into the body which grabs steel debris from your tank and motor exceptionally well! High Quality CNC machined part made in the U.S.A. Works on the oil tank drain (right side of bike) and on the oil pan drain (beneath the engine) - use two for the ultimate engine oil debris collection set-up.
Tach Drive Plug Block Off ~ Black ~ Joker Machine
Joker Machine Brand ~ Black Tach Drive Plug (Block Off). This plug is generally used when the tachometer cable drive is removed and still needs to be blocked off to prevent oil leakage. This plug has an o-ring groove machined in it for better sealing. Several bike builders just cut the stock cable off and left the Honda cable drive end installed in the valve cover. This plug is a much cleaner option in both functionality and looks. These plugs are a real nice touch when you are not using the stock tachometer, and need to eliminate the cable, or are using an electronic tach. Installs in about a minute, no need to remove the valve cover to remove the tach drive gear assy. High quality CNC machined part, made in the U.S.A.
Velocity Stack Set
Velocity Stack Set. These Velocity Stacks are a High Quality, 39mm ID, Taper Tipped Build. Set Comes Complete with 4 Velocity Stacks with Debris Screens, Set Screws and Set Screw Allen Wrench. These install easily and look amazing once installed!
Custom Black Gas/Fuel Tank Cap ~ Joker Machine
Joker Machine Brand ~ Custom Black Gas/Fuel Tank Flip Up Billet Cap. Includes Cap with a spring loaded alloy flange, replaceable rubber gasket and alloy screw attachment. Replaces OEM # 17510-323-310 Installs easily onto the tank hinges with an alloy screw (not rivets found on the stock set-up) in minutes. Lightweight design is made from a solid block of 1" thick Billet aluminum. Works with stock style latching mechanisms (Sold Separately). High quality CNC machined cap made in the U.S.A.
Custom Black Gas/Fuel Tank Cap Latch Assembly ~ Joker Machine
Joker Machine Brand ~ Custom Black Gas/Fuel Tank Cap Latch Assembly, Includes Black Latch, Return Spring and Alloy Screw attachment with nut. A fully CNC machined, billet aluminum alternative to the discontinued cast thumb latches. Install is easily made with the provided alloy screw attachment with nut. Much more durable and stronger than the original die-cast piece. High quality CNC machined part made in the U.S.A. Ties in great with our Custom Black Gas/Fuel Tank Cap (#73-1156)
Handmade Christmas Stocking
HAPPY HOLIDAYS! We are thrilled to be able to offer handmade, one-of-a-kind upcycled Christmas stockings by “Rider Ragsâ€. Featuring a CB750 on the front. They include belt, chain and Honda keychain. Each stocking is individually handmade so there will be variations in denim and belts. Some toes face right and some left. If you have a preference for right/left toe facing make a note in the order comments.
Universal Glas-Pak Insert
Universal Glas-Pak Insert - Fits 1 1/2" Pipes - Glass Pak's Actual Size 1 3/8" Tone down your TT or Drag Pipes