Honda ► CB350F ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB350F with universal parts included►
- Honda
Engine Oil Seal Kit
Engine Oil Seal Kit Kit Contains: Crankshaft Seal 1, Crankshaft Seal 2, Tachometer Seal, Right Crankcase Cover (Clutch) Seal (CB400F), Countershaft Seal, Right Crankcase Cover Seal, Gear Shift Seal, Main Shaft Seal and Clutch Lever Seal.
Gas/Fuel Tank Cap Latch Assembly ~ Black
Gas/Fuel Tank Cap Latch Assembly, Includes Black Latch with Return Spring, Latch Mounting Pin and C-Clip.
Tappet Covers
Finned Tappet Cover - Sold Each Comes With O-Ring gasket High Quality Chrome Finish
Throttle Sleeve
Nylon Throttle Sleeve - Replaces OEM # 53141-300-010
Starter Motor Seal
Starter Motor Seal - Size 24.4 x 3.1, Replaces OEM# 91312-MG7-003 / 91309-300-000 / 91309-425-003
Chrome Stock Type Front Fender
Chrome Stock Type Front Fender, Replaces OEM # 61100-333-000XW / 61100-377-000 Includes the chrome support struts, bracket for the speedo cable and the bracket to hold the brake hose in place. It does not come with hardware to secure the fender to the forks.
Headlight Setting Collar
Headlight Setting Collar, Replaces OEM# 61304-292-000 Sold Each, order the quantity you require
Cam Chain Tensioner Slipper
Cam Chain Tensioner Slipper - Replaces OEM# 14545-333-000
Matte Black ~ OEM Type Gas/Fuel Tank Cap With Latch Assembly
Matte Black OEM Type Gas/Fuel Tank Cap with Gasket, Hinge Pin (with E-Clip which Allows for easy installation) and Gas/Fuel Tank Cap Latch Assembly, Includes Latch, Return Spring, Latch Mounting Pin and C-Clip. Replaces OEM # 17510-323-310
Front Brake Pipe
Front Brake Pipe - Replaces OEM# 45128-317-701 Aprox 8" Total Length.
Dynatek Dyna S Ignition System (Ultimate Kit)
Dynatek Dyna S Ignition System (Ultimate Kit) with Dynatek Brand 5 Ohm Dual Output Coils and Dynatek Brand High Performance Spark Plug Wires. The Dyna S is a complete self-contained electronic ignition system built with the latest state-of-the-art engineering. This is the same ignition used by top racers over the past 2 decades. The Dyna S is completely housed behind the ignition cover and uses a magnetic rotor with the original spark advancer, so the factory advance curve is maintained. Increases power and reduces vibration, backfiring and intake reversion, especially on engines with radical cam timing. Front and rear cylinder timing may be set individually. Perfect for hot dual-plugged engines. The Dyna S ignition is a time proven solution to the basic ignition and trigger needs of the modern motorcycle. The Dyna S is the standard of performance and reliability. Very high quality made in the USA. Includes instructions and comes with a one year warranty through Dynatek.
Dynatek Dyna S Ignition System
Dynatek Dyna S Ignition System. The Dyna S is a complete self-contained electronic ignition system built with the latest state-of-the-art engineering. This is the same ignition used by top racers over the past 2 decades. The Dyna S is completely housed behind the ignition cover and uses a magnetic rotor with the original spark advancer, so the factory advance curve is maintained. Increases power and reduces vibration, backfiring and intake reversion, especially on engines with radical cam timing. Front and rear cylinder timing may be set individually. Perfect for hot dual-plugged engines. The Dyna S ignition is a time proven solution to the basic ignition and trigger needs of the modern motorcycle. The Dyna S is the standard of performance and reliability. Very high quality made in the USA. This ignition can be used with coils 3 ohms or higher. Includes instructions and comes with a one year warranty through Dynatek.
Clutch Lever
Clutch Lever OEM Ref # 53178-369-700 / 53190-329-010 / 53190-286-670
Brake Lever
Brake Lever OEM Ref # 53175-369-003 / 53175-300-020 / 53170-333-000
Clutch Lever ~ GP Style
Clutch Lever - Custom GP Style in Silver, This Has More of a Bend/Kickback then the stock lever. Replaces OEM # 53178-369-700
Front Brake Master Cylinder Repair Kit
Front Brake Master Cylinder Repair Kit OEM Ref # 45530-377-305
Front Master Cylinder Reservoir Diaphragm
Front Master Cylinder Reservoir Diaphragm. Replaces OEM # 45520-300-000
Turn Signal Replacement Lens
Turn Signal Replacement Lens (Amber) - Front or Rear OEM Ref # 33402-268-671
Turn Signal Lamp ~ 2 Wire Type
Signal Lamp - Amber - 12v - 2 wire for Front or Rear - Replaces OEM# 33400-341-702 / 33400-413-671. Please double check you require the 2 wire type before purchasing Stem *Our Part Number 11-2167*
Signal Lamp Lens w Gasket & Screws - Red
Red Front/Rear Turn Signal Lamp Lens with Gasket and 2 Screws. OEM Ref # 33402-268-671
Tail Light Lens Gasket
Tail Light Lens Gasket - Replaces OEM# 33709-341-671
Front/Rear Signal Lamp ~ 1 Wire Type
Signal Lamp - Amber - 12v - 1 wire for Front or Rear - Replaces OEM# 33600-447-000 / 33600-447-P00. Please double check you require the 1 wire type before purchasing Stem *Our Part Number 11-2167*
Tail Light Lens
Tail Light Lens OEM Ref # 33702-341-671
Stock Type Reflector
Stock Type Screw on Reflector, 6mm thread. Replaces OEM # 33741-340-670
Stock Type Front Reflector Rubber Base
Stock Type Front Reflector Rubber Base - Replaces OEM# 33743-341-670
Stop Light Switch
Rear Stop Light Switch OEM Ref # 35350-292-003 / 35350-KJ9-405
Ignition Switch Assembly
Ignition Switch Assembly Square End Plug Type - 4 Prong OEM Ref # 35100-341-700 / 35100-374-007 / 35100-369-740 Note: We offer an ignition switch nut tool to easily loosen or tighten the ignition switch nut without causing damage to the switch.
Black Steering Stem Nut ~ Joker Machine
Joker Machine Brand ~ Black Steering Stem Nut, Hex Nut Size 30mm. Replaces OEM # 90304-415-000 High quality CNC machined part made in the U.S.A.
High Performance Kibblewhite Valve Spring Set
High Performance Kibblewhite Valve Spring Set of 8. Made in the USA by Kibblewhite who have been making High Quality Performance parts for 75+ years. The springs in these kits are wound from super clean chrome silicon wire that has been heat treated and shot peened. These components offer optimal fitment, keeping lateral movement to a minimum. They work together as a system, providing long life, and maximum performance.
Bar Switch Assembly ~ Left (Clutch) Side
Bar Switch Assembly ~ Left (Clutch) Side - Black. Replaces OEM # 35250-300-033
Oil Filter
Oil Filter OEM Ref # 15410-426-010 / 15410-422-004 / 16099-003 / 36Y-13441-00 Note: If you require new oil filter o-rings, springs or washers we sell these on our site as well
Drain Plug Crush Washer
Drain Plug Crush Washer 12mm x 18mm x 1mm
Oil Drain Plug
Magnetic Oil Drain Plug 12mm Diameter 1.50 Thread Pitch OEM Ref # 92800-12000 / 92066-1174 / 01107-12208
Round Pod Air Filter ~ Black/Red
39mm Round Pod Air Filter ~ Black Body with Red Foam Filter - Circular style with Black end cap. Provides for greater air flow, especially when using an aftermarket exhaust and has improved flow characteristics compared to the plain wire type mesh Pod filters. Filter is supplied dry but washable filtration material may be oiled for improved dust filtration.
Oil Filter Washer - Each
Oil Filter Washer - Each 30mm OD - 20.5mm ID - .5mm Thickness Replaces OEM# 15414-300-000 Sold Each, Order the Quantity you Require
Oil Filter O-Ring Set
Oil Filter O-Ring Set Fits Oil Filter - 15410-426-005 / 15410-426-010
Foam Round Pod Air Filter
39mm Round Foam Pod Air Filter With Chrome End Caps and Rubber Mouth - Circular style.
Replacement Mirror
Replacement Mirror (R.H) 4 1/2" Diameter, 10mm Thread. Replaces OEM# 88110-333-611
Replacement Mirror
Replacement Mirror (L.H) 4 1/2" Diameter, 10mm Thread. Replaces OEM# 88120-333-611
CB Black Mirror - Original Type (Left Side)
Gloss Black CB Style Left Side Mirror - 4 1/2" Diameter with 10mm. RH Thread & 7" Stems.
CB Black Mirror - Original Type (Right Side)
Gloss Black CB Style Right Side Mirror - 4 1/2" Diameter with 10mm. RH Thread & 7" Stems.
Seat Cover
Replacement Seat Cover with Reinforced Passenger Strap (No hardware included just re-use existing hardware). There is not a "Honda" stencil on the rear of the cover due to copyright. There is a layer of foam sewn into the top of the seat cover to improve ride comfort and smooth out any defects in your seat foam. Each seat cover is made entirely by hand in North America, it is crafted slowly with great care by a gifted master upholster, using only the top grade materials available. Comes with complete installation instructions. Fits: the Original Stock Honda CB350F (1972-74) Supersport Seat Only This is for the SEAT COVER, Not the Full Seat, Photo Shows Seat Cover Installed for reference
Engine Gasket Set
Complete Engine Gasket Set Includes all Engine Gaskets High Quality - Made In Italy by Athena Athena Product # P400210850352
Gear Change Lever
Gear Change Lever Universal Fit
Gas/Fuel Tank Cap Latch Assembly
Gas/Fuel Tank Cap Latch Assembly, Includes Chrome Latch, Return Spring, Latch Mounting Pin and C-Clip.
Float Bowl Gasket
Float Bowl Gasket OEM Ref # 16019-024, 16010-323-315, 16010-323-004
Float Bowl Gasket
Float Bowl Gasket
Starter Solenoid Relay
Starter Solenoid Relay OEM Ref # 35850-375-000 / 35850-286-027
Rectifier/Regulator ~ Lithium Ion Battery Compatible
Rick's Electric Brand Lithium Ion Battery Compatible Rectifier-Regulator. Designed with a lower voltage set point to work with lithium ion batteries only. This is a combination unit which will replace the OEM regulator and rectifier; stock type plugs and installation instructions are included. Dimensions 70mm Length, 94mm Width, 27mm Height, Hole Distance 80mm Center to Center. Note: May require a custom mounting job. High quality Part. This is Not for use with standard lead acid batteries. The voltage set point is 14V +/- .2. Please ensure this set point is correct for your battery before attempting installation.
Rectifier/Regulator
Rick's Electric Brand OEM Style Honda Rectifier-Regulator: This is a combination unit which will replace the OEM regulator and rectifier; stock type plugs and installation instructions are included. Dimensions 68mm Length, 94mm Width, 26mm Height, Hole Distance 80.0mm Center to Center. High quality Part. Note: May require a custom mounting job. Works great if attached with one bolt and nut where the safety starter switch was originally located (can bypass that switch).