Honda ► CB350G ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB350G with universal parts included►
- Honda
Reservoir Cap & Diaphragm
Reservoir Cap & Diaphragm Round Thread On Type OEM Ref # 43515-MJ6-006 / 45520-300-000
Front Brake Caliper Piston Sealing Ring
Front Brake Caliper Piston Sealing Ring, Replaces OEM # 45108-300-003
Speedo Gear Plug
Speedo Gear Plug - Plug 15mm Outer Diameter, 22mm Long. This Plug is Great for Keeping your Original Speedo Drive Gear Clean.
Fuel Petcock
Fuel Petcock - Replaces OEM # 16950-292-000 - Fits M16 x 1.5 Note: Please Check that the Size Listed Above is Correct for your Bike before ordering
Rear Brake Shoes
Rear Brake Shoes Pk/2 Diameter: 159mm Width: 30mm OEM Ref # 43120-KG4-006
Brake Rod Spring
Brake Rod Spring. Replaces OEM # 95014-73100
Brake Caliper Bleed Screw Rubber Cap (Stock Type)
Stock Type Brake Caliper Bleed Screw Rubber Cap. These are the Same Design Rubber Caps as the Originals from the Factory. Replaces OEM # 45110-300-003 / 45224-579-013
Hydraulic Brake Light Switch
Hydraulic Brake Light Switch - OEM Ref # 35350-300-006 / 35350-300-016 / 341-83980-30-00 10mm x M1.25 thread
Special Oil Filter Rotor Washer
Special Angled Oil Filter Rotor Washer (16mm), Replaces OEM# 90481-292-000
Master Cylinder Rubber Boot
Master Cylinder Rubber Boot. This Boot Attaches to where the Brake Hose Joins to the Master Cylinder. Replaces OEM # 45522-300-010
Clutch Center Nut Removal Tool
Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Inside diameter 24mm, use with 3/8" driver.
Clutch Center Nut Removal Tool ~ Premium
Premium Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Both ends with 1/2 drive extension bar, Diameter 20 x 24.
Clutch Plate
Clutch Plate 8 Pieces Required OEM Ref # 22201-286-010 / 22201-415-000 / 22201-ME2-000
Steel Clutch Plate
Steel Clutch Plate B OEM Ref # 22321-KA4-700 Order the Quantity you require
Steel Clutch Plate "A"
Steel Clutch Plate "A", Replaces OEM# 22311-286-000. 1 Plate Used Per Bike
Carburetor Screw Kit
Carburetor Screw Kit (Enough For 2 Carbs) Get a new set of screws to clean up the look of your carbs! Kit Includes: 2X - Drain Screws with O-Rings 8X - 4x10 Screws w Lock Washers 8X - 4x8 Screws w Lock Washer 2X - 5x12 Screws w Lock Washers
Carb Holder with Gasket
Carb Holder with Gasket - Replaces OEM# 16211-286-040 (Holder) and 16229-369-000 (Gasket). NOTE: This is for One Holder and One Gasket, Order the Quantity you Require. If you require band clamps, this carb holder requires our carb holder clamp #15-0684
Float Needle & Seat
Float Needle & Seat High Quality - Made In Japan OEM Ref # 16011-287-004
Carb Diaphragm Rubber
Carburetor Top Diaphragm Rubber. Outer dimension 72mm - Inner dimension 25mm. Replaces the diaphragm rubber on Honda OEM# 16022-287-004 / 16022-287-014 / 16022-287-024. Note: When installing be sure to line up the rubber tab on the diaphragm so the slide is in it's proper orientation. Sold Each, order the quantity you require.
Float Bowl Drain Screw
Float Bowl Drain Screw w O-Ring. Note: We sell these each, order the quantity you require
Air Screw Needle O-Ring
Air Screw Needle O-Ring. 2.8mm x 1.2mm. Note: sold each, order the quantity you require
Seat Cover
Replacement Seat Cover with Reinforced Passenger Strap (No trim or hardware included just re-use existing hardware). There is not a "Honda" stencil on the rear of the cover due to copyright. There is a layer of foam sewn into the top of the seat cover to improve ride comfort and smooth out any defects in your original seat foam. Each seat cover is made entirely by hand in North America, it is crafted slowly with great care by a gifted master upholster, using only the top grade materials available. Comes with complete installation instructions as well as step by step instructions on how to repair damaged seat foam. This is for the SEAT COVER, Not the Full Seat, Photo Shows Seat Cover Installed for reference
Side Cover Emblem ~ Left Side
Side Cover Emblem with 2 Attachment Clips ~ For the Left Side Cover - Replaces OEM# 87126-455-000 These are great quality made of a solid cast metal. Note: This is for the Left side emblem, double check the direction the Honda wing is facing to be sure this is the side you require (other side sold separately).
Side Cover Emblem ~ Right Side
Side Cover Emblem with 2 Attachment Clips ~ For the Right Side Cover - Replaces OEM# 87125-455-000 These are great quality made of a solid cast metal. Note: This is for the Right side emblem, double check the direction the Honda wing is facing to be sure this is the side you require (other side sold separately).
Shock Absorber Nut
Shock Absorber Nut, Used when Installing Shocks. Replaces OEM # 90309-315-000 Note: Nuts sold Each, order the quantity you require
Front Sprocket Lock Plate Set
Front Sprocket Lock Plate with 2 Lock Plate Bolts. It's Always good to replace these when installing a new front sprocket. Replaces OEM # 23811-292-000 (Plate) and OEM # 92101-06016-0A (Bolts) X2.
Steering Stem Nut
Chrome Steering Stem Nut, Hex Nut Size 30mm. Replaces OEM # 90304-415-000 Note: Sold Each, order the quantity your require
Steering Stem Washer
Chrome Steering Stem Washer, Replaces OEM # 90503-283-000 Sold Each, order the quantity you require.
Side Stand Spring
Side Stand Spring, Replaces OEM # 95014-72402
Speedometer Cable
Speedometer Cable - Black - OEM Ref. # 44830-425-870 End to End Length 38.5" Made in Japan
Tachometer Cable
Tachometer Cable - Black - OEM Ref. # 37260-300-000 / 37260-449-840 Made in Japan
Front Brake Hose "A"
Front Brake Hose "A", Attaches 3-Way Joint to Front Brake Pipe. Replaces OEM # 45125-300-003
Cam Chain
Cam Chain 219T x 94 D.I.D (Daido) Takes 01-8803 Rivet Link Pitch: .3061" Side Plate: Peanut Average Tensile Strength: 1800lbs OEM Ref # 14401-286-003 / 14401-410-003
Shock Absorber Joint Rubber Set/2
Shock Absorber Joint Rubber Set/2. Replaces OEM # 52484-292-000
Front Stop Switch Sub Harness
Front Stop/Brake Switch Sub Harness, Replaces OEM # 35345-319-000
Seat Lock with Keys
Seat Lock with Keys, Replaces OEM # 77230-399-007 / 77230-107-711 This seat lock works perfect for the bikes listed but the locking mechanism sticks out a bit farther then the OEM type. If you have lost your old key you have to remove the seat lock bracket and assembly. This can be done with a short 10mm wrench or socket, once that's done the rest is easy.
Front Wheel Bearing Retainer Ring Tool
Front Wheel Bearing Retainer Ring Tool. High quality tool for removing and fitting the front wheel bearing retainer ring with 1/2 inch socket bar wrench tool hole. The perfect tool for easier removal and fitting without damaging the special retainer ring.
Front Fork Top Bridge / Triple Tree Washer Kit
Front Fork Top Bridge / Triple Tree Washer Kit of 2 Washers. These washers are needed in order to avoid broken top triple trees when you tighten up your fork tube clamps. Replace # OEM 53235-300-000
Clutch Tab Washer
Clutch Tab Washer, 16mm Size, Replaces OEM # 90431-292-000
Brake Rod Joint
Brake Rod/Arm Joint, Replaces OEM # 95015-32001
Side Stand Pivot Bolt & Nut Set
Side Stand Pivot Bolt & Nut Set, This is the Set Used to Fasten the Side Stand in Place. Replaces OEM # 90108-283-000 (Bolt) and 94002-10000-0S (Nut).
Grease Fitting Nipple (Pk/2)
Grease Fitting Nipple A .45 (Pk/2). Replaces OEM # 96201-30001
Fork Tube Set
Fork Tube Set/2, Length (555mm or 21.85"), 33mm OD. Replaces OEM# 51410-317-700 Before ordering Please Confirm 21.85" is the Length you would like
Side Cover Emblem Fixing Nut Pk/2
Side Cover Emblem Fixing Nut (3mm) Pk/2, Used to Attach the Side Cover Emblems. Replaces OEM # 90313-567-000 Check your bike to see the quantity you require
Crank Seal
Crank Seal - 30 x 42 x 8 - Replaces OEM # 91201-300-003 Note: Please Reference the OEM Number and Seal size above to make sure this is the Crank Seal you Require. Some models use 2 Different Crank Seals.
Kickstart Oil Seal
Kickstart Oil Seal - 18 x 29 x 7 - Replaces OEM # 91204-286-003
Tach Drive Oil Seal
Tach Drive Oil Seal - 4.8 x 14.5 x 4 - Replaces OEM # 91256-096-651
Front Brake Caliper Bleed Screw
Front Brake Caliper Bleed Screw. Replaces OEM # 45224-579-013
Handlebar Clutch Lever Pivot Bolt & Nut Set
Handlebar Clutch Lever Pivot Bolt & Nut Set. This is the Set that Fastens the Clutch Lever in Place. Includes One Bolt with One Nut. Replaces OEM # 90114-310-000 (Bolt) and OEM # 94001-06200-0S (Nut).
Rear Wheel Bearing Retainer
Rear Wheel Bearing Retainer - Brake Disc Side - Replaces OEM# 41231-286-000