Honda ► CB350K ►
-
Here’s our hand-picked list of electrical parts for your Honda CB350K with universal parts included►
- Honda
Starter Motor Seal
Starter Motor Seal - 60 x 1.4 - Replaces OEM# 31206-286-158 / 31206-402-008
Headlight Setting Collar
Headlight Setting Collar, Replaces OEM# 61304-292-000 Sold Each, order the quantity you require
Turn Signal Lamp Gasket
Turn Signal Lamp Gasket, Replaces OEM # 33443-268-671
Turn Signal Replacement Lens
Turn Signal Replacement Lens (Amber) - Front or Rear OEM Ref # 33402-268-671
Tail Light Assembly
Tail Light Assembly. Includes Brake Light Lens, Back Plate, Screws, Gasket, Wires, Connector and Dual Filament Bulb. Replaces OEM # 33700-292-671 / 33700-235-673 / 33701-300-671 / 33701-307-670 Two Bolt Back Mounting Bolt Pattern (Approx 96mm Center to Center), 2 Wires, Ready to Mount to your Bike!
Tail Light Assembly
Tail Light Assembly with Gasket, Replaces OEM# 33700-292-013 / 33700-237-670 / 33700-041-671
Tail Light Lens Gasket
Tail Light Lens Gasket - Replaces OEM# 33709-341-671
Turn Signal Stem
Front Signal Lamp Stay - Chrome. Body Length 65mm, Thread 25mm, Total Length 90mm. Note: We sell these in Various Lengths, Confirm this is the Size you would Like Before Purchase
Tail Light Lens Gasket
Tail Light Lens Gasket - Replaces OEM# 33709-077-671
Front/Rear Signal Lamp ~ 1 Wire Type
Signal Lamp - Amber - 12v - 1 wire for Front or Rear - Replaces OEM# 33600-447-000 / 33600-447-P00. Please double check you require the 1 wire type before purchasing Stem *Our Part Number 11-2167*
Tail Light Lens
Red Tail Light Lens with Amber Side Reflectors. OEM Ref # 33702-077-671
Tail Light Lens
Tail Light Lens OEM Ref # 33702-341-671
Stock Type Front Reflector Rubber Base
Stock Type Front Reflector Rubber Base - Replaces OEM# 33743-341-670
Stop Light Switch
Rear Stop Light Switch OEM Ref # 35350-292-003 / 35350-KJ9-405
Starter / Horn Button
Starter / Horn Button
Ignition Switch Assembly
Ignition Switch Assembly With round wire harness to switch connector. Round plug 6 Hole, 4 Wire Type. OEM Ref # 35100-303-007 / 35100-292-003 / 35100-292-013 Note: We offer an ignition switch nut tool on our site to easily loosen or tighten the ignition switch nut without causing damage to the switch
Bar Switch Assembly ~ Left (Clutch) Side
Bar Switch Assembly ~ Left (Clutch) Side - Black. Replaces OEM # 35250-300-033
Contact Point ~ Right Side
Contact Point ~ Right Side - Replaces OEM# 30203-286-004 / 30203-369-154
Contact Point ~ Left Side
Contact Point ~ Left Side - Replaces OEM# 30204-286-004 / 30202-369-154
Ignition Coil
Ignition Coil, Replaces OEM # 30500-292-672 / 30500-312-000 / 30500-286-004 / 30500-286-007 / 30500-310-670 12 Volt Single Output Ignition Coil with spark plug wire. Primary resistance 5 Ohms. Spark plug wire is 19" long, Mounting holes are approximately 80mm (3.15") apart center to center, 6.5" blue wire with dual female bullet connector, 5.25" black/white line wire with male bullet connector. Note: If you are replacing a beige Honda coil, you will need to mount it backwards as the wires come out of it differently. Other than mounting, functionality will be the same.
Starter Solenoid Relay
Starter Solenoid Relay OEM Ref # 35850-375-000 / 35850-286-027
Hot Shot Rectifier/Regulator ~ Lithium Ion Battery Compatible
Rick's Electric Brand Hot Shot Lithium Ion Battery Compatible Rectifier-Regulator. Designed with a lower voltage set point to work with lithium ion batteries only. This combination unit works with the stock stator to provide an upgraded charging system; it allows the stator to charge at full capacity 100% of the time! This is a direct plug-in combination rectifier-regulator that looks the same as the OE version & will mount in the same location as the OE rectifier for easy install. Dimensions 54mm Length, 57mm Width, 35mm Height. High quality Part. This is Not for use with standard lead acid batteries. The voltage set point is 14V +/- .2. Please ensure this set point is correct for your battery before attempting installation.
Performance Rotor
Rick's Electrics Performance Hot Shot Series Rotor, Replaces OEM# 31100-286-309 / 31100-286-004. This rotor features an upgraded design and is stronger & more powerful than the OE version.
Rectifier
Rectifier with female connector, Replaces OEM# 31700-455-671 / 31700-358-305 / 31700-358-013
Hot Shot Rectifier / Regulator
Rick's Electric Brand Hot Shot Rectifier / Regulator. Replaces OEM# 31400-292-670 / 31700-455-671 / 31700-292-008. This combination unit works with the stock stator to provide an upgraded charging system; it allows the stator to charge at full capacity 100% of the time! This is a direct plug-in combination rectifier-regulator that looks the same as the OE version & will mount in the same location as the OE rectifier for easy install. This unit is NOT compatible with lithium-ion batteries. If you have a Lithium Ion battery installed we sell a lithium ion version of this item.
Condenser
Condenser - Replaces OEM# 30250-369-004 / 30280-292-672 / 30280-292-671 / 30280-371-000
Ignition Switch Nut Tool
Ignition Switch Nut Tool, used to loosen and tighten the igntion switch nut properly without causing any damage to the switch.
Starter Motor Terminal Rubber Boot
Starter Motor Terminal (Cover) Rubber Boot. Replaces OEM # 32411-230-000
Seat Lock Bar Assembly
Seat Lock Bar Assembly, Replaces OEM# 77220-340-003 / 77220-340-011
Front Signal Lamp Stay
Front Signal Lamp Stay - Chrome. Body Length 40mm, Thread 30mm, Total Length 70mm. Note: We sell these in Various Lengths, Confirm this is the Size you would Like Before Purchase
Front Cable/ Stop Switch Clip
Front Cable Clip, This Clip Holds the Stop Switch Wires to the Cable to Keep Things Tidy. Replaces OEM # 45465-270-000
Rear Turn Signal Stay
Rear Turn Signal Stay, Replaces OEM# 33607-286-871 / 33607-286-871B Can be used on the left or right side. Sold Each, Order the Quantity you Require.
Alternator Rotor Ruller
Alternator Rotor Puller
Charging Kit ~ Lithium Ion Version
Rick's Electrics Charging Kit. Kit includes both a high quality stator and lithium-ion friendly rectifier / regulator. The kit will put out approximately 150 watts and power a 55 watt headlight. This kit is Not for use with standard lead acid batteries. The voltage set point is 14V +/- .2. Please contact the manufacturer of your Lithium Ion Battery to ensure our product has the correct set point for their product.
Charging Kit
Rick's Electrics Charging Kit for use with Standard Lead Acid Batteries. Kit includes both a high quality stator and a rectifier / regulator. The kit will put out approximately 150 watts and power a 55 watt headlight. This kit is NOT for use with lithium ion batteries. We sell a charging kit for lithium ion batteries as well.
Performance Starter Motor
Rick's Electrics Brand Performance Hot Shot Starter Motor Unit, Replaces OEM# # 31200-286-405 / 31200-286-168 / 31200-286-158. It is an upgraded 4 brush permanent magnet starter; it includes a new cable that is longer than the stock piece for easy installation.
Custom Micro Push Button/Kill Switch
Custom Micro Push Button/Kill Switch. High quality chrome switch designed to clean up the appearance of your bike while allowing the use of a switch. Works great as a hidden start/kill or horn button. Includes a contoured washer which allows for installations on round surfaces such as handlebars or frames. Switch Size 14mm x 12mm with 2X 20" wires.
Ignition Coil ~ 5 Ohm
Dual Tower Performance High Output Ignition Coil 5.2 OHM Primary resistance ignition coil, 17K OHM Secondary Resistance. Can be used with all contact point ignitions and aftermarket electronic ignitions (non CDI) requiring a 5 OHM Coil. Fits most CB's, KZ/Z1 900/1000, KZ650 etc
Dynatek Performance High Output 3 Ohm Ignition Coil Set/2 With Plug Wires
Dynatek Performance Dual Output 3 Ohm Ignition Coil Set/2 with Dynatek Performance Spark Plug Wire Set, 7mm Black Silicone Copper Core. Includes Hardware and Instructions. Comes with a one year warranty through Dynatek. Wires are 4' Length (cut to your needed length). 2 wires in this set which can be cut into 4. All wires are supplied with finished spark plug boot ends and loose coil terminals to allow the final length to be determined by the user. Wires feature a solid copper core for use on older vehicles where electrical interference is not an issue. High quality made in the USA. These high tech, top quality coils are made in the USA and are designed for maximum performance. They produce spark voltages in excess of 30,000 volts and spark energies second to none. Dyna Coils work with point ignitions, aftermarket electronic ignitions and factory electronic ignitions. Before selecting a coil check the coil primary resistance requirements as specified by the manufacturer of the ignition being used before purchasing. When choosing the right coil for your bike, never select a coil with a lower resistance than your ignition system.
Dynatek Charge Monitor
Dynatek Charge Monitor. Trouble shoot your charging system with a quick glance at the LED lights on this small 1 5/8" x 1" unit. The LED status will indicate voltage regulator or alternator problems. The Dyna Charge Monitor is a valuable addition to vehicles with a battery ignition and a charge system as found on nearly all stock vehicles. The Charge Monitor allows easy determination of the operational state of the charging system with a quick glance at the indicator LED's. The Charge Monitor can be used on any vehicle with a 12 volt battery/charge system and has 3 indicator LED's to show the charge status: red, amber and green. When the right most red LED is on the battery is being overcharged due to a faulty voltage regulator. When the green LED is on, the battery is being charged at a normal voltage. When the left most red LED is on, the battery voltage is getting very low and the charge circuit or battery is failing. High quality made in the USA. Comes with a one year warranty through the manufacturer.
Performance Tool Spark Plug Crimper Tool
Performance Tool Spark Plug Crimp Tool. Perfect crimping tool for any spark plug wires. Incorporates wire cutter, terminal crimper tool and stripper in one handy tool. Black anodized finish with insulated hand grips. Crimp slot on the end of the tool secures most ignition terminals including "W" type, right angle and "High Tower" terminals. Crimps 7mm to 8.5mm ignition wire. Works with 10 to 22 gauge solderless terminals. High quality made in the USA. Comes with a lifetime warranty through the manufacturer!
Dynatek Performance Spark Plug Wire Set
Dynatek Performance Spark Plug Wire Set, 7mm Black Silicone Copper Core. 4' Length (cut to your needed length). 2 wires in this set which can be cut into 4. All wires are supplied with finished spark plug boot ends and loose coil terminals to allow the final length to be determined by the user. Wires feature a solid copper core for use on older vehicles where electrical interference is not an issue. High quality made in the USA. Will work with Dyna Style Coils only # 07-9979, 07-9980 or 17-6810.
Dynatek Performance High Output 5 Ohm Ignition Coil Set/2
Dynatek Performance Dual Output 5 Ohm Ignition Coil Set/2. Includes Hardware and Instructions. Comes with a one year warranty through Dynatek. These high tech, top quality coils are made in the USA and are designed for maximum performance. They produce spark voltages in excess of 30,000 volts and spark energies second to none. Dyna Coils work with point ignitions, aftermarket electronic ignitions and factory electronic ignitions. Before selecting a coil check the coil primary resistance requirements as specified by the manufacturer of the ignition being used before purchasing. When choosing the right coil for your bike, never select a coil with a lower resistance than your ignition system.
Dynatek Performance High Output 3 Ohm Ignition Coil Set/2
Dynatek Performance Dual Output 3 Ohm Ignition Coil Set/2. Includes Hardware and Instructions. Comes with a one year warranty through Dynatek. These high tech, top quality coils are made in the USA and are designed for maximum performance. They produce spark voltages in excess of 30,000 volts and spark energies second to none. Dyna Coils work with point ignitions, aftermarket electronic ignitions and factory electronic ignitions. Before selecting a coil check the coil primary resistance requirements as specified by the manufacturer of the ignition being used before purchasing. When choosing the right coil for your bike, never select a coil with a lower resistance than your ignition system.
Black Universal Adjustable Headlight Brackets
Universal Adjustable Headlight Bracket Set/2 - Black Finish. Fits: 35-41mm Forks
Headlamp Visor (7")
Headlamp Visor With Eagle Emblem Fits 7" Headlight
Tommaselli Type Headlight Brackets (35mm-36mm)
Tommaselli Type Headlight Brackets 35-36mm
Headlight Bracket Set
Headlight Bracket Set - Chrome 3-Hole Type Universal Adjustable Fit - 32mm-38mm
Tommaselli Type Headlight Brackets (32mm-34mm)
Tommaselli Type Headlight Brackets 32-34mm
Headlight Bracket Set (35mm)
Aluminum Custom Headlight Brackets 35mm Headlight Mounting Holes 7/16"