Honda ► CB350K ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB350K with universal parts included►
- Honda
Exhaust Gasket (Each)
Exhaust Gasket - 1 Pc OEM Ref # 18291-286-000 / 18291-286-306 Sold Each, Order the Quantity you Require
Exhaust Gasket Pk/10
Exhaust Gasket Pk/10 OEM Ref # 18291-286-000 / 18291-286-306
Ignition Coil
Ignition Coil, Replaces OEM # 30500-292-672 / 30500-312-000 / 30500-286-004 / 30500-286-007 / 30500-310-670 12 Volt Single Output Ignition Coil with spark plug wire. Primary resistance 5 Ohms. Spark plug wire is 19" long, Mounting holes are approximately 80mm (3.15") apart center to center, 6.5" blue wire with dual female bullet connector, 5.25" black/white line wire with male bullet connector. Note: If you are replacing a beige Honda coil, you will need to mount it backwards as the wires come out of it differently. Other than mounting, functionality will be the same.
Gas Cap Rubber Seal
Gas Cap Rubber Seal, Replaces OEM # 17534-323-300
Gas/Fuel Tank Chrome Cap
Gas/Fuel Tank Chrome Cap with Gasket and Hinge Pin (with E-Clip which Allows for easy installation). Replaces OEM # 17510-323-310
Gas/Fuel Tank Cap Latch Assembly
Gas/Fuel Tank Cap Latch Assembly, Includes Chrome Latch, Return Spring, Latch Mounting Pin and C-Clip.
Gas Cap Rubber Seal
Gas Cap Rubber Seal, Replaces OEM # 17631-329-003
Float Bowl Gasket
Float Bowl Gasket OEM Ref # 16019-024, 16010-323-315, 16010-323-004
Carb Float
Brass Carb Float with Pin - Replaces OEM# 16013-286-014 Fits VM29/33 Smoothbores & most OEM CV/VM Mikuni carbs Used on Yamaha & Kawasaki up to 1980 and some Honda's
Starter Solenoid Relay
Starter Solenoid Relay OEM Ref # 35850-375-000 / 35850-286-027
Hot Shot Rectifier/Regulator ~ Lithium Ion Battery Compatible
Rick's Electric Brand Hot Shot Lithium Ion Battery Compatible Rectifier-Regulator. Designed with a lower voltage set point to work with lithium ion batteries only. This combination unit works with the stock stator to provide an upgraded charging system; it allows the stator to charge at full capacity 100% of the time! This is a direct plug-in combination rectifier-regulator that looks the same as the OE version & will mount in the same location as the OE rectifier for easy install. Dimensions 54mm Length, 57mm Width, 35mm Height. High quality Part. This is Not for use with standard lead acid batteries. The voltage set point is 14V +/- .2. Please ensure this set point is correct for your battery before attempting installation.
Performance Rotor
Rick's Electrics Performance Hot Shot Series Rotor, Replaces OEM# 31100-286-309 / 31100-286-004. This rotor features an upgraded design and is stronger & more powerful than the OE version.
Rectifier
Rectifier with female connector, Replaces OEM# 31700-455-671 / 31700-358-305 / 31700-358-013
Hot Shot Rectifier / Regulator
Rick's Electric Brand Hot Shot Rectifier / Regulator. Replaces OEM# 31400-292-670 / 31700-455-671 / 31700-292-008. This combination unit works with the stock stator to provide an upgraded charging system; it allows the stator to charge at full capacity 100% of the time! This is a direct plug-in combination rectifier-regulator that looks the same as the OE version & will mount in the same location as the OE rectifier for easy install. This unit is NOT compatible with lithium-ion batteries. If you have a Lithium Ion battery installed we sell a lithium ion version of this item.
Condenser
Condenser - Replaces OEM# 30250-369-004 / 30280-292-672 / 30280-292-671 / 30280-371-000
Side Cover Emblem
Side Cover Emblem with 2 Attachment Clips. This Emblem Came in Many Different Color Combos. This is the Black Number/White Background Version. It Will Replace Any of the Other Versions. Replaces OEM# 87128-287-010 Note: 2 Emblems Used Per Bike, Order the Quantity you Require
Fork Seals
Fork Seal Set - 33 x 44 x 8.9. Made In Japan by OEM supplier.
Fork Seals
Fork Seals Set/2 33 X 46 X 11
Steering Bearing Kit
Tapered Roller Steering Bearing Conversion Kit. Superior to OEM quality, 10X the contact area and less flex. Designed as a drop in replacement for the original bearing. Kit is complete with upper and lower tapered bearing races. High quality made in Japan.
Rear Shock Swingarm Bushing
Rear Shock Swingarm Bushing, Replaces OEM# 40548-268-000 19mm Long, 22mm OD, 10mm ID. Sold Each, Order the Quantity you Require
Engine Cover Bolt Set
High Quality Premium Stainless Steel Engine Cover Bolt Set Set includes: 34 bolts and 3 Allen keys for a total of 37 pieces. These bolts are all smooth head Allen bolts and are for the cylinder head cover, cam end covers and left and right crankcase covers.
Fuel Petcock
Fuel Petcock - Replaces OEM # 16950-292-000 - Fits M16 x 1.5 Note: Please Check that the Size Listed Above is Correct for your Bike before ordering
Rear Brake Shoes
Rear Brake Shoes Pk/2 Diameter: 159mm Width: 30mm OEM Ref # 43120-KG4-006
Brake Rod Spring
Brake Rod Spring. Replaces OEM # 95014-73100
Special Oil Filter Rotor Washer
Special Angled Oil Filter Rotor Washer (16mm), Replaces OEM# 90481-292-000
Clutch Center Nut Removal Tool
Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Inside diameter 24mm, use with 3/8" driver.
Clutch Center Nut Removal Tool ~ Premium
Premium Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Both ends with 1/2 drive extension bar, Diameter 20 x 24.
Ignition Switch Nut Tool
Ignition Switch Nut Tool, used to loosen and tighten the igntion switch nut properly without causing any damage to the switch.
Clutch Plate
Clutch Plate 8 Pieces Required OEM Ref # 22201-286-010 / 22201-415-000 / 22201-ME2-000
Steel Clutch Plate
Steel Clutch Plate B OEM Ref # 22321-KA4-700 Order the Quantity you require
Steel Clutch Plate "A"
Steel Clutch Plate "A", Replaces OEM# 22311-286-000. 1 Plate Used Per Bike
Carburetor Screw Kit
Carburetor Screw Kit (Enough For 2 Carbs) Get a new set of screws to clean up the look of your carbs! Kit Includes: 2X - Drain Screws with O-Rings 8X - 4x10 Screws w Lock Washers 8X - 4x8 Screws w Lock Washer 2X - 5x12 Screws w Lock Washers
Carb Rebuild Kit
Carb Rebuild Kit for carbs with ROUND CARB BOWLS. Note: Each Kit Rebuilds One Carb, Order the Quantity of Kits you Require
Carb Holder with Gasket
Carb Holder with Gasket - Replaces OEM# 16211-286-040 (Holder) and 16229-369-000 (Gasket). NOTE: This is for One Holder and One Gasket, Order the Quantity you Require. If you require band clamps, this carb holder requires our carb holder clamp #15-0684
Float Needle & Seat
Float Needle & Seat High Quality - Made In Japan OEM Ref # 16011-287-004
Carb Diaphragm Rubber
Carburetor Top Diaphragm Rubber. Outer dimension 72mm - Inner dimension 25mm. Replaces the diaphragm rubber on Honda OEM# 16022-287-004 / 16022-287-014 / 16022-287-024. Note: When installing be sure to line up the rubber tab on the diaphragm so the slide is in it's proper orientation. Sold Each, order the quantity you require.
Float Bowl Drain Screw
Float Bowl Drain Screw w O-Ring. Note: We sell these each, order the quantity you require
Air Screw Needle O-Ring
Air Screw Needle O-Ring. 2.8mm x 1.2mm. Note: sold each, order the quantity you require
Seat Cover
Replacement Seat Cover with Reinforced Passenger Strap (No trim or hardware included just re-use existing hardware). There is not a "Honda" stencil on the rear of the cover due to copyright. Each seat cover is made entirely by hand in North America, it is crafted slowly with great care by a gifted master upholster, using only the top grade materials available. Comes with complete installation instructions as well as step by step instructions on how to repair damaged seat foam. This is for the SEAT COVER, Not the Full Seat, Photo Shows Seat Cover Installed for reference
Seat Cover
Replacement Seat Cover with Reinforced Passenger Strap (No trim or hardware included just re-use existing hardware). There is not a "Honda" stencil on the rear of the cover due to copyright. There is a layer of foam sewn into the top of the seat cover to improve ride comfort and smooth out any defects in your original seat foam. Each seat cover is made entirely by hand in North America, it is crafted slowly with great care by a gifted master upholster, using only the top grade materials available. Comes with complete installation instructions as well as step by step instructions on how to repair damaged seat foam. This is for the SEAT COVER, Not the Full Seat, Photo Shows Seat Cover Installed for reference
Side Cover Emblem ~ Left Side
Side Cover Emblem with 2 Attachment Clips ~ For the Left Side Cover These are great quality made of a solid cast metal. Note: This is for the Left side emblem, double check the direction the Honda wing is facing to be sure this is the side you require (other side sold separately).
Side Cover Emblem ~ Right Side
Side Cover Emblem with 2 Attachment Clips ~ For the Right Side Cover - Replaces OEM# 87128-317-670 / 87129-317-670 These are great quality made of a solid cast metal. Note: This is for the Right side emblem, double check the direction the Honda wing is facing to be sure this is the side you require (other side sold separately).
Side Cover Emblem ~ Left Side
Side Cover Emblem with 2 Attachment Clips ~ For the Left Side Cover - Replaces OEM# 87126-344-671 These are great quality made of a solid cast metal. Note: This is for the Left side emblem, double check the direction the Honda wing is facing to be sure this is the side you require (other side sold separately).
Side Cover Emblem ~ Right Side
Side Cover Emblem with 2 Attachment Clips ~ For the Right Side Cover - Replaces OEM# 87125-344-671 These are great quality made of a solid cast metal. Note: This is for the Right side emblem, double check the direction the Honda wing is facing to be sure this is the side you require (other side sold separately).
Side Cover Emblem
Side Cover Emblem with 2 Attachment Clips. This Emblem Came in Many Different Color Combos. This is the White Number/Burgundy Background Version. It Will Replace Any of the Other Versions. Replaces OEM# 87128-287-010 Note: 2 Emblems Used Per Bike, Order the Quantity you Require
Shock Absorber Nut
Shock Absorber Nut, Used when Installing Shocks. Replaces OEM # 90309-315-000 Note: Nuts sold Each, order the quantity you require
Front Sprocket Lock Plate Set
Front Sprocket Lock Plate with 2 Lock Plate Bolts. It's Always good to replace these when installing a new front sprocket. Replaces OEM # 23811-292-000 (Plate) and OEM # 92101-06016-0A (Bolts) X2.
Steering Stem Nut
Chrome Steering Stem Nut, Hex Nut Size 30mm. Replaces OEM # 90304-415-000 Note: Sold Each, order the quantity your require
Steering Stem Washer
Chrome Steering Stem Washer, Replaces OEM # 90503-283-000 Sold Each, order the quantity you require.
Side Stand Spring
Side Stand Spring, Replaces OEM # 95014-72402