Honda ► CB360G ►
-
Here’s our hand-picked list of electrical parts for your Honda CB360G with universal parts included that match “honda sl125”►
- Honda
Stock Type Reflector
Stock Type Screw on Reflector, 6mm thread. Replaces OEM # 33741-340-670
Stop Light Switch
Rear Stop Light Switch OEM Ref # 35350-292-003 / 35350-KJ9-405
Rectifier
Rectifier with female connector, Replaces OEM# 31700-455-671 / 31700-358-305 / 31700-358-013
Headlight Setting Collar
Headlight Setting Collar, Replaces OEM# 61304-292-000 Sold Each, order the quantity you require
Front Stop Switch Sub Harness
Front Stop/Brake Switch Sub Harness, Replaces OEM # 35345-319-000
Seat Lock Bar Assembly
Seat Lock Bar Assembly, Replaces OEM# 77220-340-003 / 77220-340-011
Performance Starter Motor
Rick's Electrics Brand Performance Hot Shot Starter Motor Unit, Replaces OEM# # 31200-286-405 / 31200-286-168 / 31200-286-158. It is an upgraded 4 brush permanent magnet starter; it includes a new cable that is longer than the stock piece for easy installation.
Rear Signal Lamp Stay
Rear Signal Lamp Stay - Chrome Rear type - OEM Ref # 33441-369-000 125mm Long.
Hot Shot Rectifier / Regulator
Rick's Electric Brand Hot Shot Rectifier / Regulator. Replaces OEM# 31400-292-670 / 31700-455-671 / 31700-292-008. This combination unit works with the stock stator to provide an upgraded charging system; it allows the stator to charge at full capacity 100% of the time! This is a direct plug-in combination rectifier-regulator that looks the same as the OE version & will mount in the same location as the OE rectifier for easy install. This unit is NOT compatible with lithium-ion batteries. If you have a Lithium Ion battery installed we sell a lithium ion version of this item.
Contact Point ~ Left Side
Contact Point ~ Left Side - Replaces OEM# 30204-286-004 / 30202-369-154
Tail Light Lens Gasket
Tail Light Lens Gasket - Replaces OEM# 33709-341-671
Front Signal Lamp Stay
Front Signal Lamp Stay - Chrome. Body Length 40mm, Thread 30mm, Total Length 70mm. Note: We sell these in Various Lengths, Confirm this is the Size you would Like Before Purchase
Turn Signal Replacement Lens
Turn Signal Replacement Lens (Amber) - Front or Rear OEM Ref # 33402-268-671
Contact Point ~ Right Side
Contact Point ~ Right Side - Replaces OEM# 30203-286-004 / 30203-369-154
6 1/2" Headlamp Unit
6 1/2" Outer Diameter Headlamp Unit. This unit can be used with various headlights requiring a 6 1/2" headlamp. Can replace OEM# 33120-333-670 / 33100-333-671 but this unit does not have any mounting clips on the rear sides of the headlamp unit. Does Not Include mounting hardware. This unit comes with a H4 60/55w bulb, all glass lens with pilot light.
Front/Rear Signal Lamp ~ 1 Wire Type
Signal Lamp - Amber - 12v - 1 wire for Front or Rear - Replaces OEM# 33600-447-000 / 33600-447-P00. Please double check you require the 1 wire type before purchasing Stem *Our Part Number 11-2167*
Turn Signal Lamp ~ 2 Wire Type
Signal Lamp - Amber - 12v - 2 wire for Front or Rear - Replaces OEM# 33400-341-702 / 33400-413-671. Please double check you require the 2 wire type before purchasing Stem *Our Part Number 11-2167*
Hydraulic Brake Light Switch
Hydraulic Brake Light Switch - OEM Ref # 35350-300-006 / 35350-300-016 / 341-83980-30-00 10mm x M1.25 thread
Turn Signal Lamp Gasket
Turn Signal Lamp Gasket, Replaces OEM # 33443-268-671
Starter Solenoid Relay
Starter Solenoid Relay OEM Ref # 35850-375-000 / 35850-286-027
Starter Motor Seal
Starter Motor Seal - 60 x 1.4 - Replaces OEM# 31206-286-158 / 31206-402-008
Condenser
Condenser - Replaces OEM# 30250-369-004 / 30280-292-672 / 30280-292-671 / 30280-371-000
Starter Motor Terminal Rubber Boot
Starter Motor Terminal (Cover) Rubber Boot. Replaces OEM # 32411-230-000
Hydraulic Brake Light Switch
Hydraulic Brake Light Switch Banjo Bolt Type - 10mm x M1.25 Can Be Used Front/Rear At Single Banjo Brake Line Fitting Correct Thread For Most Honda/Kawasaki/Yamaha Stock Fittings
Universal 1 Ohm Dual Output 6V Ignition Coil
Universal 1 Ohm Dual Output 6V Ignition Coil. Will work on a number of Honda, Kawasaki, Suzuki, Yamaha, Norton, BSA, Triumph and other motorcycles with 6 volt dual output ignition coils. Check the coil mount spacing on your bike before you order. Mounting holes are 90mm (3.5") apart center to center. Low tension wires 390mm (15") long. Female spade connectors at the coil and male and female bullet connectors at the other ends. Spark plug wires (high tension leads) 570mm (24") long with 300mm (12") protective sheath.