Honda ► CB360K ►
-
Here’s our hand-picked list of carburetor parts for your Honda CB360K with universal parts included►
- Honda
Carb Rebuild Kit
Carb Rebuild Kit. Note: Each Kit Rebuilds One Carb, Order the Quantity of Kits you Require
Carb Holder Set
Carb Holder Set (Set of 2 with Gaskets). Replace those old cracked or dried up carb holders with a brand new set! Replaces OEM #'s 16211-369-000 X2 and 16229-369-000 X2 NOTE-If you require band clamps, these carb holders require our 46-49mm diameter clamps part #15-0685 X2.
Carb Intake Manifold
Carb Intake Manifold - Replaces OEM# 16211-369-000 NOTE: This is for One Holder, Order the Quantity you Require. If you require band clamps, these carb holders require our clamps part #15-0685
Carb Slide Diaphragm Rubber Set
Carb Slide Diaphragm Rubbers Set - Includes 2 Diaphragms (Rubber Portion Only as Shown) and 2 O-Rings. Replaces Rubber Portion on OEM# 16022-369-004
Float Needle & Seat
Float Needle & Seat High Quality - Made In Japan OEM Ref # 16011-369-004
Float Bowl Drain Screw
Float Bowl Drain Screw w O-Ring. Note: We sell these each, order the quantity you require
Throttle Adjusting Bolt
Throttle Adjusting Bolt, Replaces OEM # 53190-300-000
Throttle Adjusting Spring
Throttle Adjusting Spring, Replaces OEM # 53191-300-000
Gear Clamp 40-60mm.
Universal Gear Clamp for Carb Holders or Air Boxes. 9mm Wide. Adjusts with a screwdriver. Fits: Diameters 40-60mm (With a width of 9mm)
Universal Band Clamp
Universal Band Clamp for Carb Holders or Air Boxes Fits: Diameters 53-56mm. (1.92" - 2.16")
Universal Band Clamp
Universal Band Clamp for Carb Holders or Air Boxes Fits: Diameters 60mm-65mm or 2.36" to 2.56"
Universal Band Clamp
Universal Band Clamp for Carb Holders or Air Boxes Fits: Diameters 41-44mm. (1.53" - 1.69")
Universal Band Clamp
Universal Band Clamp for Carb Holders or Air Boxes Fits: Diameters 46-49mm. (1.77" - 1.92")
Universal Band Clamp
Universal Band Clamp for Carb Holders or Air Boxes Fits: Diameters 66-69mm. (2.48" - 2.63")
Universal Band Clamp
Universal Band Clamp for Carb Holders or Air Boxes Fits: Diameters 69-72mm. (2.67" - 2.87")
Band Clamp 45-47mm.
Universal Band Clamp for Carb Holders or Air Boxes Fits: Diameters 45-47mm.
Band Clamp 50-52mm.
Universal Band Clamp for Carb Holders or Air Boxes Fits: Diameters 50-52mm.
Band Clamp 58-60mm.
Universal Band Clamp for Carb Holders or Air Boxes Fits: Diameters 58-60mm.
Band Clamp 43-49mm
Band Clamp for Air Filters, Airbox to Carb Joints, Custom Manifolds to Filter Joints and all purpose uses except carb holders. Fits: 43-49mm. (1.69"-1.93") Diameters
Band Clamp 67mm-73mm
Band Clamp for Air Filters, Airbox to Carb Joints, Custom Manifolds to Filter Joints and all purpose uses except carb holders. Fits: 67-73mm. (2.64"-2.87") Diameters
Band Clamp 73mm-79mm
Band Clamp for Air Filters, Airbox to Carb Joints, Custom Manifolds to Filter Joints and all purpose uses except carb holders. Fits: 73-79mm. (2.87"-3.11") Diameters
Band Clamp 79-85mm
Band Clamp for Air Filters, Airbox to Carb Joints, Custom Manifold to Filter Joints and all purpose uses except carb holders. Fits: 79-85mm. (3.11"-3.35") Diameters
Band Clamp 85-91mm
Band Clamp for Air Filters, Airbox to Carb Joints, Custom Manifolds to Filter Joints and all purpose uses except carb holders. Fits: 85-91mm. (3.35"-3.58") Diameters
Band Clamp 91-97mm
Band Clamp for Air Filters, Airbox to Carb Joints, Custom Manifolds to Filter Joints and all purpose uses except carb holders. Fits: 91-97mm (3.58"-3.82") Diameters
Band Clamp 97mm-103mm
Band Clamp for Air Filters, Airbox to Carb Joints, Custom Manifolds to Filter Joints and all purpose uses except carb holders. Fits: 97-103mm (3.82"-4.00") Diameters
Band Clamp 103mm-109mm
Band Clamp for Air Filters, Airbox to Carb Joints, Custom Manifolds to Filter Joints and all purpose uses except carb holders. Fits: 103-109mm (4.00"-4.29") Diameters
Band Clamp 109mm-115mm
Band Clamp for Air Filters, Airbox to Carb Joints, Custom Manifolds to Filter Joints and all purpose uses except carb holders. Fits: 109-115mm (4.29"-4.53") Diameters
Band Clamp 115mm-121mm
Band Clamp for Air Filters, Airbox to Carb Joints, Custom Manifolds to Filter Joints and all purpose uses except carb holders. Fits: 115-121mm. (4.53"-4.76") Diameters
Band Clamp 121mm-127mm
Band Clamp for Air Filters, Airbox to Carb Joints, Custom Manifolds to Filter Joints and all purpose uses except carb holders. Fits: 121-127mm. (4.76"-5.00") Diameters
Band Clamp 37-43mm
Band Clamp for Air Filters, Airbox to Carb Joints, Custom Manifold to Filter Joints and all purpose uses except carb holders. Fits: 37-43mm. (1.45"-1.69") Diameters
Band Clamp 78-80mm
Universal Band Clamp for Carb Holders or Air Boxes Fits: Diameters 78-80mm.
Professional Carb Rebuild Shop Kit - 4mm x 400 JIS Phillips Pan-Head Assortment
401 Piece JIS Phillips Pan-Head Bolt Set with Plastic Case. All the screws you typically need when rebuild carbs that require 4mm machine screws. This includes the carbs found on many early Kawasaki KZ and Suzuki GS models. Includes Sizes 4X8, 4X10, 4X12, 4X14, 4X16, 4X18 and 4X20.
Professional Carb Rebuild Shop Kit - 5mm x 600 JIS Phillips Pan-Head Assortment
601 Piece JIS Phillips Pan-Head Bolt Set with Plastic Case. All the screws you typically need when rebuild carbs that require 5mm machine screws. This includes the carbs found on many Kawasaki KZ, Suzuki GS, Yamaha XS models with CV carbs. Includes Sizes 5X8, 5X10, 5X12, 5X14, 5X16, 5X18
Carb Rebuild Shop Kit - 4mm x 800 Bolt/Washer Assortment
802 Piece Stainless Steel Socket Head Bolt Set with Plastic Case. All the screws you typically need when rebuilding carbs that require 4mm machine screws. This includes the carbs found on many early Kawasaki KZ and Suzuki GS models. Includes Sizes 4x8, 4x10, 4x12, 4x14, 4x16, 4x18, 4x20
Carb Rebuild Shop Kit - 5mm x 1,200 Bolt/Washer Assortment
1202 Piece Stainless Steel Socket Head Bolt Set with Plastic Case. All the screws you typically need when rebuilding carbs that require 5mm machine screws. This includes the carbs found on many Kawasaki KZ, Suzuki GS, Yamaha XS models with CV carbs. Includes Sizes 5X8, 5X10, 5X12, 5X14, 5X16, 5X18
Carb Float Level Gauge
Carburetor Float Level Gauge. Used to measure the float height between the float and carburetor gasket surface. It is important to make sure the float height is correct to factory spec when tuning your engine. Too little or too much fuel in the float bowl will negatively affect tuning results. Adjustable to fit most carburetors. Adjustable Width: 16-78mm and Adjustable Height 0-40mm
Hose Remover Pliers
Hose Remover Pliers. For easy removal of 5/32" to 1/2" hoses. The jaw digs into the tube to grip it, squeeze and the hose is easily pushed off by the jaw.
382pc O-Rings Kit with Plastic Case
382pc O-Rings Kit with Plastic Case. 30 different sizes included in mm's. QTY---Width----Inside Dia.---------QTY---Width-----Inside Dia. 20X---1.78mm--2.90mm------------13X---2.62mm--9.19mm 20X---1.78mm--3.69mm------------13X---2.62mm--10.77mm 20X---1.78mm--4.47mm------------13X---2.62mm--12.37mm 20X---1.78mm--5.29mm------------13X---2.62mm--13.95mm 20X---1.78mm--6.07mm------------13X---2.62mm--15.54mm 20X---1.78mm--7.65mm------------13X---2.62mm--17.12mm 20X---1.78mm--9.25mm------------13X---2.62mm--18.72mm 10X---3.53mm--18.64mm----------10X---3.53mm--31.34mm 10X---3.53mm--20.22mm----------10X---3.53mm--32.92mm 10X---3.53mm--21.82mm----------10X---3.53mm--34.52mm 10X---3.53mm--23.39mm----------10X---3.53mm--36.10mm 10X---3.53mm--25.00mm----------10X---3.53mm--37.70mm 10X---3.53mm--26.57mm------------7X---5.34mm--37.47mm 10X---3.53mm--28.17mm------------7X---5.34mm--40.65mm 10X---3.53mm--29.75mm------------7X---5.34mm--43.82mm
419pc O-Rings Kit with Plastic Case
419pc O-Rings Kit with Plastic Case. 32 different sizes included metric sizes. QTY---Width----Inside Dia.---------QTY---Width-----Inside Dia. 20X---1.50mm--3.00mm------------13X---2.50mm--11.00mm 23X---1.50mm--7.00mm------------14X---2.50mm--13.00mm 23X---1.50mm--10.0mm------------13X---2.50mm--14.00mm 23X---1.50mm--13.0mm------------14X---2.50mm--16.00mm 20X---2.00mm--4.40mm------------14X---2.50mm--18.00mm 18X---2.00mm--5.00mm------------13X---2.50mm--19.00mm 14X---2.50mm--10.0mm------------14X---2.50mm--21.00mm 13X---2.50mm--22.00mm----------10X---3.50mm--31.00mm 10X---3.50mm--18.00mm----------10X---3.50mm--33.00mm 10X---3.50mm--20.00mm----------10X---3.50mm--34.50mm 10X---3.50mm--22.00mm----------10X---3.50mm--36.00mm 10X---3.50mm--23.50mm----------10X---3.50mm--38.00mm 10X---3.50mm--25.00mm----------10X---3.50mm--41.00mm 10X---3.50mm--26.50mm----------10X---3.50mm--44.00mm 10X---3.50mm--28.00mm----------10X---3.50mm--47.00mm 10X---3.50mm--30.00mm----------10X---3.50mm--50.00mm
Carburetor Adjusting Tool
Carburetor Adjusting Tool. Works with Mikuni or Keihin carbs. 11" long tool with a 8mm hex nut and screwdriver slot adjusting bolt. This combo design allows unlocking of the locknut, adjustments to the balancing screw and re-locking the lock nut in one step.
Carburetor Synchronizer Vacuum Gauge ~ 2,3,4 Cylinders
Carburetor and throttle body synchronizer kit for bikes with 2, 3 or 4 Cylinders. Makes synching your carburetor setup fast and easy! For use with Honda, Kawasaki, and Suzuki models (which typically have 5mm connections) that use sets of 2, 3 or 4 cylinders. Includes 4 easy to read gauges, Mountable bracket, 180mm extensions - 5mm threads, 65mm extensions - 5mm threads,Necessary hoses, Dampening valves (included to help control needle jump) and instructions.
Carb Cleaning Tool Set
Carburetor Cleaning Tool Set. Includes 20 steel wire ends designed for cleaning the tiny holes found in carburetor jets. Cleaning wire sizes range from 0.45mm to 1.5mm.
Fluid Hose Clamp
Fluid Hose Clamp, all steel construction with adjustable locking collar. Completely or partially closes flexible brake, fuel, and vacuum fluid lines.
Portable Auxiliary Fuel Tank Tool
Portable Auxiliary Fuel Tank, for Non Fuel Injection Systems. Includes 4 Feet of 1/4" fuel line and an inline fuel valve with 1/4" inlet and outlet. Fuel capacity 2 Litres. For use when tuning a motorcycle with the gas tank removed. Note: This tool is not to be used for long term fuel storage, for safety and to prevent accidental spillage, immediately drain gas back to approved long term storage container after use.
Carb Cleaning Tool Set
Carburetor Cleaning Tool Set. Includes 12 steel wire ends and a small file designed for cleaning nozzles and the tiny holes found in carburetor passages and jets.
Carburetor Synchronizer Vacuum Gauge ~ 2 Carb Synchronizer
Carburetor and throttle body synchronizer kit for bikes with 2 Carbs. Makes synching your carburetor setup fast and easy! For use with Honda, Kawasaki, and Suzuki models (which typically have 5mm connections) that use sets of 2 carbs. Includes 2 easy to read gauges, Mountable bracket, 180mm extensions - 5mm threads, 65mm extensions - 5mm threads,Necessary hoses, Dampening valves (included to help control needle jump) and instructions.