Honda ► CB400F ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB400F that match “screws nuts bolts tools”►
- Honda
Signal Lamp Lens w Gasket & Screws - Red
Red Front/Rear Turn Signal Lamp Lens with Gasket and 2 Screws. OEM Ref # 33402-268-671
Brake Caliper Bleed Screw Rubber Cap (Stock Type)
Stock Type Brake Caliper Bleed Screw Rubber Cap. These are the Same Design Rubber Caps as the Originals from the Factory. Replaces OEM # 45110-300-003 / 45224-579-013
Rectifier/Regulator
Rick's Electric Brand OEM Style Honda Rectifier-Regulator: This is a combination unit which will replace the OEM regulator and rectifier; stock type plugs and installation instructions are included. Dimensions 68mm Length, 94mm Width, 26mm Height, Hole Distance 80.0mm Center to Center. High quality Part. Note: May require a custom mounting job. Works great if attached with one bolt and nut where the safety starter switch was originally located (can bypass that switch).
Drain Plug Crush Washer
Drain Plug Crush Washer 12mm x 18mm x 1mm
Oil Drain Plug
Magnetic Oil Drain Plug 12mm Diameter 1.50 Thread Pitch OEM Ref # 92800-12000 / 92066-1174 / 01107-12208
Custom Performance Magnetic Oil Drain Plug ~ Joker Machine
Joker Machine Brand ~ Custom Performance Magnetic Oil Drain Plug - 12mm. Dia x M1.5 - OEM Ref # 92800-12000 Plug features an extended length HIGH POWER "rare earth" Neodymium-Iron-Boron Magnet pressed into the body which grabs steel debris from your tank and motor exceptionally well! High Quality CNC machined part made in the U.S.A. Works on the oil tank drain (right side of bike) and on the oil pan drain (beneath the engine) - use two for the ultimate engine oil debris collection set-up.
Exhaust Stud Set
Exhaust Stud Set. Includes 8 Exhaust Studs, 8 Washers and 8 Nuts.
Tach Drive Plug Block Off ~ Black ~ Joker Machine
Joker Machine Brand ~ Black Tach Drive Plug (Block Off). This plug is generally used when the tachometer cable drive is removed and still needs to be blocked off to prevent oil leakage. This plug has an o-ring groove machined in it for better sealing. Several bike builders just cut the stock cable off and left the Honda cable drive end installed in the valve cover. This plug is a much cleaner option in both functionality and looks. These plugs are a real nice touch when you are not using the stock tachometer, and need to eliminate the cable, or are using an electronic tach. Installs in about a minute, no need to remove the valve cover to remove the tach drive gear assy. High quality CNC machined part, made in the U.S.A.
Side Stand Rubber Hardware Set
Side Stand Rubber Hardware Set, Includes Metal Collar, Bolt and Washer.
Stock Type Reflector
Stock Type Screw on Reflector, 6mm thread. Replaces OEM # 33741-340-670
Front Sprocket Lock Plate Set
Front Sprocket Lock Plate with 2 Lock Plate Bolts. It's Always good to replace these when installing a new front sprocket. Replaces OEM # 23811-292-000 (Plate) and OEM # 92101-06016-0A (Bolts) X2.
Pilot Indicator Light Cover
Pilot Indicator Light Cover, Replaces OEM# 37600-377-018 This includes the front and rear cover with fastening screws.
Velocity Stack Set
Velocity Stack Set. These Velocity Stacks are a High Quality, 39mm ID, Taper Tipped Build. Set Comes Complete with 4 Velocity Stacks with Debris Screens, Set Screws and Set Screw Allen Wrench. These install easily and look amazing once installed!
Custom Brake Rod Adjuster Knob ~ Joker Machine
Joker Machine Brand ~ Custom Brake Rod Adjuster Knob, Replaces OEM # 95015-42000 Gives your bike a great custom look while refining the quality of your brake adjuster knob! Makes for super easy brake adjustments due to the choice of a knurled outside knob and a hex nut feature all in one. High quality CNC machined part, made in the U.S.A.