Honda ► CB400F ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB400F that match “wiring harness”►
- Honda
Alternator Stator Wire Harness
Alternator Stator Wire Harness. Connects to the Stator and Field Coil. Replaces OEM # 31110-333-000
USA/Canadian Version Wire Harness
USA/Canadian Version Main Wire Harness Loom - OEM # 32100-377-030 Fits: Honda CB400F (1975-77) Supersport NOTE: These fit model years and type listed, other years and bikes use a different OEM part number (there is a difference!).
Starter Clutch Diode
Starter Clutch Diode OEM Ref # 31700-124-003 / 31700-166-008
Bar Switch Assembly ~ Left (Clutch) Side
European Version (8 Wire) Bar Switch Assembly ~ Left (Clutch) Side - Black. Please be sure to double check your harness requires this 8 wire type switch Before ordering. Replaces OEM # 35200-377-671 Note: Wiring to be run Inside the handlebar.
Turn Signal Lamp ~ 2 Wire Type
Signal Lamp - Amber - 12v - 2 wire for Front or Rear - Replaces OEM# 33400-341-702 / 33400-413-671. Please double check you require the 2 wire type before purchasing Stem *Our Part Number 11-2167*
Front/Rear Signal Lamp ~ 1 Wire Type
Signal Lamp - Amber - 12v - 1 wire for Front or Rear - Replaces OEM# 33600-447-000 / 33600-447-P00. Please double check you require the 1 wire type before purchasing Stem *Our Part Number 11-2167*
Pilot Indicator Light Cover
Pilot Indicator Light Cover, Replaces OEM# 37600-377-018 This includes the front and rear cover with fastening screws.
Handlebar - Stock Type ~ CB400F 1975-76
Stock Type Handlebar for the CB400F (1975-76) - Chrome. The holes are pre-cut for routing the wiring from the switches to the harness. There are also holes drilled to fit the pins in the stock switches to keep them from rotating. Bar Diameter - 7/8" - 22mm Length - 27 1/4" - 692mm Pull Back - 3 1/2" - 89mm Inner Rise - 2 1/4" - 57mm End Rise - 3 1/4" - 82mm Center Width - 5 1/4" - 133mm Base Width - 7" - 178mm Knurl Width - 4 1/2" - 114mm Control Length - 8 1/2" - 216mm Drilled - YES Replaces OEM # 53100-377-000 Note: These Are Drilled For Wires
Turn Signal Lamp
Turn Signal Lamp - Glossy Black 3 Wire - Dual Filament Left Front / Right Rear * For Single Filament, Use 2 of 3 Wire *
Turn Signal Lamp
Turn Signal Lamp - Glossy Black 3 Wire - Dual Filament Right Front / Left Rear * For Single Filament, Use 2 of 3 Wire *
Turn Signal Lamp
Turn Signal Lamp - Front 2-Wire OEM Ref # 33400-377-671 / 33400-460-671 / 33400-460-679
Dynatek Dyna S Ignition System (Ultimate Kit)
Dynatek Dyna S Ignition System (Ultimate Kit) with Dynatek Brand 5 Ohm Dual Output Coils and Dynatek Brand High Performance Spark Plug Wires. The Dyna S is a complete self-contained electronic ignition system built with the latest state-of-the-art engineering. This is the same ignition used by top racers over the past 2 decades. The Dyna S is completely housed behind the ignition cover and uses a magnetic rotor with the original spark advancer, so the factory advance curve is maintained. Increases power and reduces vibration, backfiring and intake reversion, especially on engines with radical cam timing. Front and rear cylinder timing may be set individually. Perfect for hot dual-plugged engines. The Dyna S ignition is a time proven solution to the basic ignition and trigger needs of the modern motorcycle. The Dyna S is the standard of performance and reliability. Very high quality made in the USA. Includes instructions and comes with a one year warranty through Dynatek.
Dynatek Dyna S Ignition System
Dynatek Dyna S Ignition System. The Dyna S is a complete self-contained electronic ignition system built with the latest state-of-the-art engineering. This is the same ignition used by top racers over the past 2 decades. The Dyna S is completely housed behind the ignition cover and uses a magnetic rotor with the original spark advancer, so the factory advance curve is maintained. Increases power and reduces vibration, backfiring and intake reversion, especially on engines with radical cam timing. Front and rear cylinder timing may be set individually. Perfect for hot dual-plugged engines. The Dyna S ignition is a time proven solution to the basic ignition and trigger needs of the modern motorcycle. The Dyna S is the standard of performance and reliability. Very high quality made in the USA. This ignition can be used with coils 3 ohms or higher. Includes instructions and comes with a one year warranty through Dynatek.
Rectifier/Regulator
Rectifier-Regulator: This is a combination unit which will replace the OEM regulator and rectifier. This has the OEM type ground wiring and Stock Type Plugs. Dimensions 80mm Length, 94mm Width, 27mm Height, Hole Distance 70.0mm Center to Center. Instructions not included.
High Performance Kibblewhite Valve Spring Set
High Performance Kibblewhite Valve Spring Set of 8. Made in the USA by Kibblewhite who have been making High Quality Performance parts for 75+ years. The springs in these kits are wound from super clean chrome silicon wire that has been heat treated and shot peened. These components offer optimal fitment, keeping lateral movement to a minimum. They work together as a system, providing long life, and maximum performance.
Round Pod Air Filter ~ Black/Red
39mm Round Pod Air Filter ~ Black Body with Red Foam Filter - Circular style with Black end cap. Provides for greater air flow, especially when using an aftermarket exhaust and has improved flow characteristics compared to the plain wire type mesh Pod filters. Filter is supplied dry but washable filtration material may be oiled for improved dust filtration.