Honda ► CB400F ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB400F with universal parts included that match “1”►
- Honda
6 1/2" Headlamp Unit
6 1/2" Outer Diameter Headlamp Unit. This unit can be used with various headlights requiring a 6 1/2" headlamp. Can replace OEM# 33120-333-670 / 33100-333-671 but this unit does not have any mounting clips on the rear sides of the headlamp unit. Does Not Include mounting hardware. This unit comes with a H4 60/55w bulb, all glass lens with pilot light.
Front/Rear Signal Lamp ~ 1 Wire Type
Signal Lamp - Amber - 12v - 1 wire for Front or Rear - Replaces OEM# 33600-447-000 / 33600-447-P00. Please double check you require the 1 wire type before purchasing Stem *Our Part Number 11-2167*
Cam Chain Tensioner Slipper
Cam Chain Tensioner Slipper - Replaces OEM# 14545-333-000
Carburetor Screw Kit
Carburetor Screw Kit. Get a new set of screws to clean up the look of your carbs! Kit Includes: 4X - Drain Screws with O-Rings 16X- 4x12 Screws w Lock Washers 8X - 5x16 Screws w Lock Washers 2X - 6x14 Screws w Lock Washers
Side Cover Rubber Grommet
Side Cover Rubber / Headlight Stay Grommet, Replaces OEM# 17245-369-000 Fits: Honda CB360K (1974) - 1 Used Per Side Cover, CB360G (1974) - 1 Used Per Side Cover, CB360T (1975) - Frame #2100001 + - 1 Used Per Side Cover, CB360T (1976) - 1 Used Per Side Cover, CL360K (1974-75) - 1 Used Per Side Cover CB400F (1975-77) Supersport - 1 Used Per Side Cover + 2 Also used on the Headlight Stay.
Drain Plug Crush Washer
Drain Plug Crush Washer 12mm x 18mm x 1mm
Steel Clutch Plate B
Steel Clutch Plate B, Replaces OEM# 22321-333-010 1 Used Per Bike
Front Brake Pipe
Front Brake Pipe - Replaces OEM# 45128-317-701 Aprox 8" Total Length.
Handlebar - Stock Type ~ CB400F 1975-76
Stock Type Handlebar for the CB400F (1975-76) - Chrome. The holes are pre-cut for routing the wiring from the switches to the harness. There are also holes drilled to fit the pins in the stock switches to keep them from rotating. Bar Diameter - 7/8" - 22mm Length - 27 1/4" - 692mm Pull Back - 3 1/2" - 89mm Inner Rise - 2 1/4" - 57mm End Rise - 3 1/4" - 82mm Center Width - 5 1/4" - 133mm Base Width - 7" - 178mm Knurl Width - 4 1/2" - 114mm Control Length - 8 1/2" - 216mm Drilled - YES Replaces OEM # 53100-377-000 Note: These Are Drilled For Wires
Stock Type Air Filter
Stock Type Air Filter - OEM Ref # 17210-333-610
Carb Float
Carb Float with Pin, Replaces OEM # 16013-333-004 Note: 4 Carb Floats Used Per Bike, Order Quantity you Require
Stock Style Stator
Stock Style Stator, Replaces OEM # 31102-333-004
Condenser
Condenser OEM Ref # 30250-333-004
Cam Chain
219H x 82 Cam Chain - OEM Ref. # 14401-333-003 The latest high strength cam chain from D.I.D. Japan.
Tachometer Cable
Tachometer Cable - OEM Ref # 37260-333-000 Made in Japan
Starter Motor Seal
Starter Motor Seal - 60 x 1.4 - Replaces OEM# 31206-286-158 / 31206-402-008
Oil Drain Plug
Magnetic Oil Drain Plug 12mm Diameter 1.50 Thread Pitch OEM Ref # 92800-12000 / 92066-1174 / 01107-12208
Replacement Mirror
Replacement Mirror (R.H) 4 1/2" Diameter, 10mm Thread. Replaces OEM# 88110-333-611
Replacement Mirror
Replacement Mirror (L.H) 4 1/2" Diameter, 10mm Thread. Replaces OEM# 88120-333-611
CB Black Mirror - Original Type (Left Side)
Gloss Black CB Style Left Side Mirror - 4 1/2" Diameter with 10mm. RH Thread & 7" Stems.
CB Black Mirror - Original Type (Right Side)
Gloss Black CB Style Right Side Mirror - 4 1/2" Diameter with 10mm. RH Thread & 7" Stems.
Exhaust Gasket (Each)
Exhaust Gasket - 1 Pc OEM Ref # 18291-028-000 / 18291-028-306 Sold Each, Order the Quantity you Require
Athena Engine Gasket Set
Complete Engine Gasket Set Includes all Engine Gaskets High Quality - Made In Italy by Athena Athena Product # P400210850401/1
Carb Rebuild Kit
Carb Rebuild Kit Includes Items Pictured High Quality - Made In Japan 1 Kit Needed Per Carb
Air Screw Needle O-Ring
Air Screw Needle O-Ring. 2.8mm x 1.2mm. Note: sold each, order the quantity you require
CB400F 1975 ~ Varnish Blue & Light Ruby Red Models ~ Warning and Service Label Set
Honda CB400F (1975) Supersport ~ Varnish Blue & Light Ruby Red Models ~ Warning & Service Label (Sticker) Set. This set includes several warning and service labels that were originally found on these bikes when new. You'll find the quality & accuracy of these decals second to none and accurate in every detail. These reproductions will add the finishing touch to your restoration. This 10 piece warning & service label set includes: 1 - Important Information 1 - Loading Warning 1 - Caution: Battery 2 - Honda Showa 2 - Helmet Holder 1 - Exhaust Modification 1 - Preserve Nature 1 - Honda Motor Co. These decals are no longer available from the manufacturer. All decals are "printed" on the highest quality materials from companies such as 3M and Avery. All decals have a protective coating to resist scratching and to protect colors from UV rays. These decals are adhesive backed for simple application.
Drive Chain Adjuster
Drive Chain Adjuster with Nut and Bolt, Replaces OEM# 40543-471-000 / 40543-312-010. If you require 2 adjusters purchase 2 of this part.
Starter Motor Seal
Starter Motor Seal - Size 24.4 x 3.1, Replaces OEM# 91312-MG7-003 / 91309-300-000 / 91309-425-003
Front Brake Caliper Piston
Front Brake Caliper Piston (1) - 38.15mm Diameter x 34mm Height - Replaces OEM # 45107-323-020. Please note: the side with the 2mm outer lip faces the brake pad during install.
Hydraulic Brake Light Switch
Hydraulic Brake Light Switch - OEM Ref # 35350-300-006 / 35350-300-016 / 341-83980-30-00 10mm x M1.25 thread
Clutch Center Nut Removal Tool ~ Premium
Premium Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Both ends with 1/2 drive extension bar, Diameter 20 x 24.
Engine Oil Seal Kit
Engine Oil Seal Kit Kit Contains: Crankshaft Seal 1, Crankshaft Seal 2, Tachometer Seal, Right Crankcase Cover (Clutch) Seal (CB400F), Countershaft Seal, Right Crankcase Cover Seal, Gear Shift Seal, Main Shaft Seal and Clutch Lever Seal.
Front Wheel Bearing Retainer Ring Tool
Front Wheel Bearing Retainer Ring Tool. High quality tool for removing and fitting the front wheel bearing retainer ring with 1/2 inch socket bar wrench tool hole. The perfect tool for easier removal and fitting without damaging the special retainer ring.
Steering Stem Nut
Chrome Steering Stem Nut, Hex Nut Size 30mm. Replaces OEM # 90304-415-000 Note: Sold Each, order the quantity your require
Steering Stem Washer
Chrome Steering Stem Washer, Replaces OEM # 90503-283-000 Sold Each, order the quantity you require.
Stock Type Gas/Fuel Tank
Stock Type Gas/Fuel Tank. Tank comes in primer grey ready for you to paint your color of choice. Fits: Honda CB400F (1975-76) Supersport Requires a 14mm x 1.0 threaded nut petcock (Our #20-0092 will work), does not accept stock type petcock Does not include gas cap #20-0045, petcock, emblems or any other items.
Kick Stand Stopper Rubber
Kick Stand Stopper Rubber "A" - Replaces OEM# 95011-61000.
Rear Wheel Bearing Retainer
Rear Wheel Bearing Retainer - Brake Disc Side - Replaces OEM# 41231-286-000
Side Cover Rubber
Side Cover Rubber, Replaces OEM# 83621-333-000 2 Used Per Side Cover, Order The Quantity You Require
Front Sprocket ~ 17 Tooth
Front Sprocket ~ 17 Tooth Replaces OEM# 23801-333-000 / 23801-300-315 Please Count your sprocket teeth and check your chain length before ordering to ensure this is correct for your bike. Please note: for the CB450K (1968-69) - some bikes used 15 tooth sprockets, for the CB750K (1969-70) use this sprocket upto engine #SN1003527 only, for the CL450 (1967/1969) some bikes used 15 or 16 tooth sprockets.
Custom Performance Magnetic Oil Drain Plug ~ Joker Machine
Joker Machine Brand ~ Custom Performance Magnetic Oil Drain Plug - 12mm. Dia x M1.5 - OEM Ref # 92800-12000 Plug features an extended length HIGH POWER "rare earth" Neodymium-Iron-Boron Magnet pressed into the body which grabs steel debris from your tank and motor exceptionally well! High Quality CNC machined part made in the U.S.A. Works on the oil tank drain (right side of bike) and on the oil pan drain (beneath the engine) - use two for the ultimate engine oil debris collection set-up.
Custom Black Gas/Fuel Tank Cap ~ Joker Machine
Joker Machine Brand ~ Custom Black Gas/Fuel Tank Flip Up Billet Cap. Includes Cap with a spring loaded alloy flange, replaceable rubber gasket and alloy screw attachment. Replaces OEM # 17510-323-310 Installs easily onto the tank hinges with an alloy screw (not rivets found on the stock set-up) in minutes. Lightweight design is made from a solid block of 1" thick Billet aluminum. Works with stock style latching mechanisms (Sold Separately). High quality CNC machined cap made in the U.S.A.
Fork Dust Boot Set
Fork Seal Dust Boots (Set/2). 33mm Size, Replaces OEM # 91254-413-881
Black Steering Stem Nut ~ Joker Machine
Joker Machine Brand ~ Black Steering Stem Nut, Hex Nut Size 30mm. Replaces OEM # 90304-415-000 High quality CNC machined part made in the U.S.A.
Front Brake Caliper Bleed Screw
Front Brake Caliper Bleed Screw. Replaces OEM # 45224-579-013
Cylinder Head Gasket
Cylinder Head Gasket, Replaces OEM# 12909-428-003 / 12909-283-000 / 12909-333-000.
Oil Filter Washer - Each
Oil Filter Washer - Each 30mm OD - 20.5mm ID - .5mm Thickness Replaces OEM# 15414-300-000 Sold Each, Order the Quantity you Require
Fork Seals
Fork Seals Set/2 33 X 46 X 11
Oil Pressure Switch
Oil Pressure Switch, Replaces OEM # 37240-P13-013
Headlight Setting Collar
Headlight Setting Collar, Replaces OEM# 61304-292-000 Sold Each, order the quantity you require