Honda ► CB450K ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB450K that match “screws nuts bolts tools”►
- Honda
Ignition Switch Nut Tool
Ignition Switch Nut Tool, used to loosen and tighten the igntion switch nut properly without causing any damage to the switch.
Side Stand Pivot Bolt & Nut Set
Side Stand Pivot Bolt & Nut Set, This is the Set Used to Fasten the Side Stand in Place. Replaces OEM # 90108-283-000 (Bolt) and 94002-10000-0S (Nut).
Handlebar Clutch Lever Pivot Bolt & Nut Set
Handlebar Clutch Lever Pivot Bolt & Nut Set. This is the Set that Fastens the Clutch Lever in Place. Includes One Bolt with One Nut. Replaces OEM # 90114-310-000 (Bolt) and OEM # 94001-06200-0S (Nut).
Custom Drive Chain Adjuster Screws ~ Black ~ Joker Machine
Joker Machine Brand ~ Black Custom Type Drive Chain Adjuster Screws (Set of 2) with Gold Cadium Plated Nuts. Replace OEM # 90119-283-000 Features a CNC Machined Knob Section with 3 methods of Adjusting (By Hand with the Knurled Section, With an Open or Box Wrench on the Hex or with an Allen Wrench through the End of the Knob to the Screw). These Adjuster Screws Look Very Sharp and Improve the Look of your Bike. High Quality Made in the U.S.A.
Ignition Switch Assembly
Ignition Switch Assembly With round wire harness to switch connector. Round plug 6 Hole, 4 Wire Type. OEM Ref # 35100-303-007 / 35100-292-003 / 35100-292-013 Note: We offer an ignition switch nut tool on our site to easily loosen or tighten the ignition switch nut without causing damage to the switch
Float Bowl Drain Screw
Float Bowl Drain Screw w O-Ring. Note: We sell these each, order the quantity you require
Drive Chain Adjuster
Drive Chain Adjuster with Nut and Bolt, Replaces OEM# 95014-18000 / 40543-390-000 / 40532-283-010. If you require 2 adjusters purchase 2 of this part.
Side Cover Emblem Fixing Nut Pk/2
Side Cover Emblem Fixing Nut (3mm) Pk/2, Used to Attach the Side Cover Emblems. Replaces OEM # 90313-567-000 Check your bike to see the quantity you require
Tail Light Assembly
Tail Light Assembly. Includes Brake Light Lens, Back Plate, Screws, Gasket, Wires, Connector and Dual Filament Bulb. Replaces OEM # 33700-292-671 / 33700-235-673 / 33701-300-671 / 33701-307-670 Two Bolt Back Mounting Bolt Pattern (Approx 96mm Center to Center), 2 Wires, Ready to Mount to your Bike!
Swingarm Pivot Bolt Locknut with Washer
Swingarm Pivot Bolt Locknut with Locknut Washer. Replaces OEM # 90354-268-000 (Locknut) and OEM # 90526-268-000 (Washer).
Signal Lamp Lens w Gasket & Screws - Red
Red Front/Rear Turn Signal Lamp Lens with Gasket and 2 Screws. OEM Ref # 33402-268-671
Joker Machine Magnetic Oil Drain Plug
Joker Machine Magnetic Oil Drain Plug with O-Ring, Replaces OEM# 90013-312-000. High quality made from 6061 billet aluminum. High power rare earth neodymium-iron boron magnet pressed into the body that exceptionally grabs steel debris from your tank and motor. M33.7 - 1.5mm thread pitch. Installs with a 19mm socket. - 45mm outside diameter and 19mm off the case.
Special Oil Filter Rotor Washer
Special Angled Oil Filter Rotor Washer (16mm), Replaces OEM# 90481-292-000
Front Sprocket Lock Plate Set
Front Sprocket Lock Plate with 2 Lock Plate Bolts. It's Always good to replace these when installing a new front sprocket. Replaces OEM # 23811-292-000 (Plate) and OEM # 92101-06016-0A (Bolts) X2.
Custom Brake Rod Adjuster Knob ~ Joker Machine
Joker Machine Brand ~ Custom Brake Rod Adjuster Knob, Replaces OEM # 95015-42000 Gives your bike a great custom look while refining the quality of your brake adjuster knob! Makes for super easy brake adjustments due to the choice of a knurled outside knob and a hex nut feature all in one. High quality CNC machined part, made in the U.S.A.