Honda ► CB450K ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB450K with universal parts included►
- Honda
Contact Point ~ Left Side
Contact Point ~ Left Side - Replaces OEM# 30204-292-003 / 30204-292-154
Replacement Mirror
Replacement Mirror (R.H) 4 1/2" Diameter, 10mm Thread. Replaces OEM# 88110-333-611
Replacement Mirror
Replacement Mirror (L.H) 4 1/2" Diameter, 10mm Thread. Replaces OEM# 88120-333-611
Stock Type Mirror Set
Stock Type Mirror Set/2, Replaces OEM# 88110-329-730 / 88110-074-000 / 88120-329-730 / 88120-074-000 Chrome Mirrors, 8" Stem Length
Exhaust Gasket (Each)
Exhaust Gasket - 1 Pc OEM Ref # 18291-283-010 / 18291-ME9-000 / 18291-MM8-880 Sold Each, Order the Quantity you Require
Exhaust Gasket Pk/10
Exhaust Gasket Pk/10 OEM Ref # 18291-283-010 / 18291-ME9-000 / 18291-MM8-880
Ignition Coil
Ignition Coil, Replaces OEM # 30500-292-672 / 30500-312-000 / 30500-286-004 / 30500-286-007 / 30500-310-670 12 Volt Single Output Ignition Coil with spark plug wire. Primary resistance 5 Ohms. Spark plug wire is 19" long, Mounting holes are approximately 80mm (3.15") apart center to center, 6.5" blue wire with dual female bullet connector, 5.25" black/white line wire with male bullet connector. Note: If you are replacing a beige Honda coil, you will need to mount it backwards as the wires come out of it differently. Other than mounting, functionality will be the same.
Overhaul Gasket Set
Engine Overhaul Gasket Set Fits: Honda CB450K (1965-74) - 5 Speed Models Only, CL450K (1968-74), CB500T (1975-76)
Engine Gasket Set
Complete Engine Gasket Set Includes all Engine Gaskets High Quality - Made In Italy by Athena Athena Product #P400210850450
Gear Change Lever
Gear Change Lever Universal Fit Spline Diameter 11.5mm Total Length 6 1/2" Offset 4"
Front Spoke & Nipple Set
Front Spoke & Nipple Set (19") Front Disc Brake Wheel OEM Ref # 97451-69246 / 97B11-69245
Gas Cap Rubber Seal
Gas Cap Rubber Seal, Replaces OEM # 17525-300-000
Gas/Fuel Tank Chrome Cap
Gas/Fuel Tank Chrome Cap with Gasket and Hinge Pin (with E-Clip which Allows for easy installation). Replaces OEM # 17510-323-310
Gas/Fuel Tank Cap Latch Assembly
Gas/Fuel Tank Cap Latch Assembly, Includes Chrome Latch, Return Spring, Latch Mounting Pin and C-Clip.
Gas Cap Rubber Seal
Gas Cap Rubber Seal, Replaces OEM # 17631-329-003
Carb Float
Carb Float with Pin, Replaces OEM # 16013-283-004 Note: Sold Each, Order Quantity of Floats your Bike Requires.
Starter Solenoid Relay
Starter Solenoid Relay OEM Ref # 35850-375-000 / 35850-286-027
Hot Shot Rectifier/Regulator ~ Lithium Ion Battery Compatible
Rick's Electric Brand Hot Shot Lithium Ion Battery Compatible Rectifier-Regulator. Designed with a lower voltage set point to work with lithium ion batteries only. This combination unit works with the stock stator to provide an upgraded charging system; it allows the stator to charge at full capacity 100% of the time! This is a direct plug-in combination rectifier-regulator that looks the same as the OE version & will mount in the same location as the OE rectifier for easy install. Dimensions 54mm Length, 57mm Width, 35mm Height. High quality Part. This is Not for use with standard lead acid batteries. The voltage set point is 14V +/- .2. Please ensure this set point is correct for your battery before attempting installation.
Performance Charging Kit ~ Lithium Ion Version
Rick's Electrics High Performance Hot Shot Lithium Ion Battery Compatible Charging Kit. This high performance Hot Shot charging kit includes both a new rotor and a lithium-ion battery compatible combination rectifier / regulator which looks like the stock unit and mounts in the same location. The kit will put out approximately 150 watts: 50% over stock. You do NOT need to replace your OE stator unless it tests bad, this kit works with the OE stator. This kit is Not for use with standard lead acid batteries. The voltage set point is 14V +/- .2. Please contact the manufacturer of your Lithium Ion Battery to ensure our product has the correct set point for their product.
Performance Charging Kit
Rick's Electrics High Performance Hot Shot Standard Lead Acid Battery Compatible Charging Kit. This high performance Hot Shot charging kit includes both a new rotor and a standard lead acid battery compatible combination rectifier / regulator which looks like the stock unit and mounts in the same location. The kit will put out approximately 150 watts: 50% over stock. You do NOT need to replace your OE stator unless it tests bad, this kit works with the OE stator. This kit is NOT for use with lithium ion batteries. We sell a charging kit for lithium ion batteries as well.
Rectifier
Rectifier with female connector, Replaces OEM# 31700-455-671 / 31700-358-305 / 31700-358-013
Hot Shot Rectifier / Regulator
Rick's Electric Brand Hot Shot Rectifier / Regulator. Replaces OEM# 31400-292-670 / 31700-455-671 / 31700-292-008. This combination unit works with the stock stator to provide an upgraded charging system; it allows the stator to charge at full capacity 100% of the time! This is a direct plug-in combination rectifier-regulator that looks the same as the OE version & will mount in the same location as the OE rectifier for easy install. This unit is NOT compatible with lithium-ion batteries. If you have a Lithium Ion battery installed we sell a lithium ion version of this item.
Condenser
Condenser - Replaces OEM# 30250-369-004 / 30280-292-672 / 30280-292-671 / 30280-371-000
Fork Seals
Fork Seals Set/2 35 X 48 X 10.5/11
Stock Type Fork Gaitors
Black Stock Type Fork Gaitors (Set/2) OEM Ref. # 51611-300-000
Fork Seals
Fork Seal Set - 35 x 46 x 11. Made In Japan by OEM supplier. Replaces OEM # 91255-292-003
Fork Gaiters
Fork Gaiters OEM Ref # 51611-300-000 Note: These are about 1.75" shorter then the stock type but will work fine
Fork Spacer Trim Set
Chrome Front Fork Spacer Trim Set/2. These are the Chrome Ribs that Cover the Top of the Fork Boots. Replaces OEM # 51608-300-000
Wheel Seal Kit
Rear Wheel Seal Kit 1 Seal 34 x 55 x 9
High Performance Kibblewhite Bronze Swingarm Bushing Set
High Performance Kibblewhite Bronze Swingarm Bushing Set/2. Replaces OEM# 52108-457-300, 52108-422-300. Made in the USA by Kibblewhite who have been making High Quality Performance parts for 75+ years. Kibblewhite bronze bushings offers increased durability and better fitment then the OEM type bushings.
Steering Bearing Kit
Tapered Roller Steering Bearing Conversion Kit. Superior to OEM quality, 10X the contact area and less flex. Designed as a drop in replacement for the original bearing. Kit is complete with upper and lower tapered bearing races. High quality made in Japan.
Rear Wheel Bearing Retainer
Rear Wheel Bearing Retainer - Sprocket Side - Replaces OEM# 41231-283-000 This retainer is used on the (sprocket side) of the bike.
Front Wheel Bearing Retainer
Front Wheel Bearing Retainer - Replaces OEM# 44643-300-000
Rear Shock Swingarm Bushing
Rear Shock Swingarm Bushing, Replaces OEM# 40548-268-000 19mm Long, 22mm OD, 10mm ID. Sold Each, Order the Quantity you Require
Engine Cover Bolt Set
High Quality Premium Stainless Steel Engine Cover Bolt Set Set includes: 23 bolts and 2 Allen keys for a total of 25 pieces. These bolts are all smooth head Allen bolts and are for the visible covers only.
Master Cylinder Reservoir Cap
Master Cylinder Cap with Plastic O-Ring. Replaces OEM # 45513-341-771 This style of master cylinder cap was discontinued long ago by Honda. We have had these produced again to keep your bike looking sharp. Spruce up your Master Cylinder with one of these great looking master cylinder caps!
Front Brake Caliper Piston
Front Brake Caliper Piston (1) - 38.15mm Diameter x 34mm Height - Replaces OEM # 45107-323-020. Please note: the side with the 2mm outer lip faces the brake pad during install.
Master Cylinder Reservoir Cap Plastic O-Ring
Master Cylinder Reservoir Cap Plastic O-Ring, Replaces OEM # 45521-MJ6-006
Reservoir Cap & Diaphragm
Reservoir Cap & Diaphragm Round Thread On Type OEM Ref # 43515-MJ6-006 / 45520-300-000
Front Brake Caliper Piston
Front Brake Caliper Piston. Replaces OEM # 45107-300-003
Front Brake Caliper Piston Sealing Ring
Front Brake Caliper Piston Sealing Ring, Replaces OEM # 45108-300-003
Speedo Gear Plug
Speedo Gear Plug - Plug 15mm Outer Diameter, 22mm Long. This Plug is Great for Keeping your Original Speedo Drive Gear Clean.
Fuel Petcock
Fuel Petcock - Replaces OEM # 16950-292-000 - Fits M16 x 1.5 Note: Please Check that the Size Listed Above is Correct for your Bike before ordering
Front Brake Pads
Front Brake Pads Pk/2 OEM Ref # 45105-390-006A
Front Brake Pads
Front Brake Pads Pk/2 OEM Ref # 45105-341-000A
Brake Rod Spring
Brake Rod Spring. Replaces OEM # 95014-73100
Headlight Adjusting Screw & Spring Set
Headlight Adjusting Screw & Spring Set. Each Set Includes One Screw and One Spring. Replaces OEM # 33103-346-670 (Screw) and OEM # 33107-300-003 (Spring)
Front Brake Caliper Adjuster Set
Front Brake Caliper Adjuster Set. Includes Adjusting Bolt, Spring, Washer and Nut.
Front Brake Caliper Bleed Screw
Front Brake Caliper Bleed Screw. Replaces OEM # 45109-300-003
Brake Caliper Bleed Screw Rubber Cap (Stock Type)
Stock Type Brake Caliper Bleed Screw Rubber Cap. These are the Same Design Rubber Caps as the Originals from the Factory. Replaces OEM # 45110-300-003 / 45224-579-013