Honda ► CB450K ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB450K with universal parts included that match “screws nuts bolts tools”►
- Honda
![Honda CB450K Swingarm Pivot Bolt Locknut with Washer](/images/parts/100/29-7022.jpg)
Swingarm Pivot Bolt Locknut with Washer
Swingarm Pivot Bolt Locknut with Locknut Washer. Replaces OEM # 90354-268-000 (Locknut) and OEM # 90526-268-000 (Washer).
![Honda CB450K Front Brake Caliper Bolts (Pk/2)](/images/parts/100/73-1026.jpg)
Front Brake Caliper Bolts (Pk/2)
Front Brake Caliper Bolts (Pk/2), Replaces OEM # 90165-300-023
![Honda CB450K Front Brake Caliper Bolt & Washer Set](/images/parts/100/73-1027.jpg)
Front Brake Caliper Bolt & Washer Set
Front Brake Caliper Bolt & Washer Set. Set includes 2 Bolts and 2 Washers. Replaces OEM # 90165-323-000
![Honda CB450K Signal Lamp Lens w Gasket & Screws - Red](/images/parts/100/11-2160.jpg)
Signal Lamp Lens w Gasket & Screws - Red
Red Front/Rear Turn Signal Lamp Lens with Gasket and 2 Screws. OEM Ref # 33402-268-671
![Honda CB450K Brake Caliper Bleed Screw Rubber Cap (Stock Type)](/images/parts/100/29-7018.jpg)
Brake Caliper Bleed Screw Rubber Cap (Stock Type)
Stock Type Brake Caliper Bleed Screw Rubber Cap. These are the Same Design Rubber Caps as the Originals from the Factory. Replaces OEM # 45110-300-003 / 45224-579-013
![Honda CB450K Joker Machine Magnetic Oil Drain Plug](/images/parts/100/12-0108.jpg)
Joker Machine Magnetic Oil Drain Plug
Joker Machine Magnetic Oil Drain Plug with O-Ring, Replaces OEM# 90013-312-000. High quality made from 6061 billet aluminum. High power rare earth neodymium-iron boron magnet pressed into the body that exceptionally grabs steel debris from your tank and motor. M33.7 - 1.5mm thread pitch. Installs with a 19mm socket. - 45mm outside diameter and 19mm off the case.
![Honda CB450K Stock Type Reflector](/images/parts/100/11-2303.jpg)
Stock Type Reflector
Stock Type Screw on Reflector, 6mm thread. Replaces OEM # 33741-340-670
![Honda CB450K Special Oil Filter Rotor Washer](/images/parts/100/29-7034A.jpg)
Special Oil Filter Rotor Washer
Special Angled Oil Filter Rotor Washer (16mm), Replaces OEM# 90481-292-000
![Honda CB450K Front Sprocket Lock Plate Set](/images/parts/100/49-0782.jpg)
Front Sprocket Lock Plate Set
Front Sprocket Lock Plate with 2 Lock Plate Bolts. It's Always good to replace these when installing a new front sprocket. Replaces OEM # 23811-292-000 (Plate) and OEM # 92101-06016-0A (Bolts) X2.
![Honda CB450K Custom Brake Rod Adjuster Knob ~ Joker Machine](/images/parts/100/73-1072.jpg)
Custom Brake Rod Adjuster Knob ~ Joker Machine
Joker Machine Brand ~ Custom Brake Rod Adjuster Knob, Replaces OEM # 95015-42000 Gives your bike a great custom look while refining the quality of your brake adjuster knob! Makes for super easy brake adjustments due to the choice of a knurled outside knob and a hex nut feature all in one. High quality CNC machined part, made in the U.S.A.
![Honda CB450K Custom Black Gas/Fuel Tank Cap ~ Joker Machine](/images/parts/100/73-1156.jpg)
Custom Black Gas/Fuel Tank Cap ~ Joker Machine
Joker Machine Brand ~ Custom Black Gas/Fuel Tank Flip Up Billet Cap. Includes Cap with a spring loaded alloy flange, replaceable rubber gasket and alloy screw attachment. Replaces OEM # 17510-323-310 Installs easily onto the tank hinges with an alloy screw (not rivets found on the stock set-up) in minutes. Lightweight design is made from a solid block of 1" thick Billet aluminum. Works with stock style latching mechanisms (Sold Separately). High quality CNC machined cap made in the U.S.A.
![Honda CB450K Side Cover Emblem](/images/parts/100/99-4865.jpg)
Side Cover Emblem
Side Cover Emblem, with the Attachment Clips for the rear of the emblem (You must use your old bolt and washers that attach at the front of the emblem) Replaces OEM# 87125-457-670 Super high quality, cast metal emblem. Note: 2 Emblems Used Per Bike, Order the Quantity you Require
![Honda CB450K Custom Fork Boot Collars ~ Joker Machine](/images/parts/100/12-0072.jpg)
Custom Fork Boot Collars ~ Joker Machine
Joker Machine Brand ~ Custom Fully CNC Machined Fork Boot Collar Set/2. A great solution for giving your stock bike (with the sheet metal headlight ears), an open fork tube Cafe look, while giving you an upper attachment point in order to retain your stock accordion style O.E.M. fork Gaitors. Designed to fit easily onto 35MM fork tubes and may be adjusted up-or-down along the tube into position, then tightened into place with the recessed set screw located in the groove (totally invisible).
![Honda CB450K Side Cover Emblem](/images/parts/100/48-9508.jpg)
Side Cover Emblem
Cast Metal Side Cover Emblem with the 3 Attachment Clips for the rear of the emblem (You must use your old bolt and washers that attach at the front of the emblem). Replaces OEM # 87130-294-010 / 87130-319-671 / 87125-346-670 Note: There are a few different styles of side cover emblems used on these bikes. Be sure to verify this design is the type you need before purchasing. Note: 2 Emblems Used Per Bike, Order the Quantity you Require
![Honda CB450K Carburetor Adjusting Tool](/images/parts/100/35-0084.jpg)
Carburetor Adjusting Tool
Carburetor Adjusting Tool. Works with Mikuni or Keihin carbs. 11" long tool with a 8mm hex nut and screwdriver slot adjusting bolt. This combo design allows unlocking of the locknut, adjustments to the balancing screw and re-locking the lock nut in one step.
![Honda CB450K Screw Extractor Set](/images/parts/100/35-9048.jpg)
Screw Extractor Set
Screw Extractor Set 5 Pc Set 1/8", 3/16", 15/64", 5/16", 3/8" Used to remove broken off studs, bolts & screws.
![Honda CB450K Safety Wire Nut & Metric Bolt Drill Jig Kit](/images/parts/100/35-0064.jpg)
Safety Wire Nut & Metric Bolt Drill Jig Kit
Safety Wire Nut & Metric Bolt Drill Jig Kit. Contains one nut drill jig and one metric bolt jig. Jig set designed for accurate drilling of nuts and bolts for use with safety lock wire. Both jigs can be mounted in a vice for drilling. The nut drill jig allows the safety wire holes to be drilled through the head of bolts or through nuts, across the diagonal easily. Accepts up to a 3.5mm diameter. Metric bolt drill jig provides 6 drill holes for metric sizes 6 X 1.0, 8 X 1.0, 8 X 1.25, 10 X 1.25, 10 X 1.5 and 12 X 1.5 bolts.
![Honda CB450K Safety Wire Nut & Metric+Imperial Bolt Drill Jig Kit](/images/parts/100/35-0065.jpg)
Safety Wire Nut & Metric+Imperial Bolt Drill Jig Kit
Safety Wire Nut & Metric+Imperial Bolt Drill Jig Kit. Contains one nut drill jig, one metric bolt jig and one imperial bolt jig. Jig set designed for accurate drilling of nuts and bolts for use with safety lock wire. Both jigs can be mounted in a vice for drilling. The nut drill jig allows the safety wire holes to be drilled through the head of bolts or through nuts, across the diagonal easily. Accepts up to a 3.5mm diameter. Metric bolt drill jig provides 6 drill holes for metric sizes 6 X 1.0, 8 X 1.0, 8 X 1.25, 10 X 1.25, 10 X 1.5 and 12 X 1.5 bolts. Imperial bolt drill jig provides 6 drill holes for imperial sizes 1/4"-20, 5/16"-18, 5/16"-24, 3/8"-16, 3/8"-24 and 7/16"-14 bolts.
![Honda CB450K Tappet Adjusting Tool Set](/images/parts/100/35-0042.jpg)
Tappet Adjusting Tool Set
Tappet Adjusting Tool Set 4 Piece Set For both 9mm & 10mm valve adjuster screw locknuts. Screwdriver tip & 4mm square tip for valve adjuster screws. For Honda/Yamaha/Suzuki
![Honda CB450K Fork Cap Socket Tool](/images/parts/100/35-1082.jpg)
Fork Cap Socket Tool
19mm Fork Cap Socket Tool, This Tool Is Needed To Loosen Or Remove The Front Fork Cap Bolts On Many Bikes
![Honda CB450K Tappet Adjusting Tool Set](/images/parts/100/35-4200.jpg)
Tappet Adjusting Tool Set
Tappet Adjusting Tool Set 6 Piece Set Includes T-Socket Wrenches - 8mm, 9mm, 10mm Sizes 3 Adjusters - Slotted Screw, 3mm Square, 4mm Square
![Honda CB450K Gold Bullet Shaped License Plate Bolt](/images/parts/100/49-0105.jpg)
Gold Bullet Shaped License Plate Bolt
Gold Colored Bullet Shaped Bolt with Nut and Washer. These bullet shaped bolts are made from cast aluminum. The Bullet is 3/4" tall with a 3/4" round base. The 3/4" long x 1/4"-20 threaded stud is removable. There are many uses for these bolts including license plate holder bolts and more! They can be mounted to about anything using 1/4"-20 bolts or screws to hold the bullets in place. Note: Sold Each, Order the Quantity you Require
![Honda CB450K Chrome Bullet Shaped License Plate Bolt](/images/parts/100/73-0089.jpg)
Chrome Bullet Shaped License Plate Bolt
Chrome Bullet Shaped Bolt with Nut and Washer. These bullet shaped bolts are made from cast aluminum. The Bullet is 3/4" tall with a 3/4" round base. The 3/4" long x 1/4"-20 threaded stud is removable. There are many uses for these bolts including license plate holder bolts and more! They can be mounted to about anything using 1/4"-20 bolts or screws to hold the bullets in place. Note: Sold Each, Order the Quantity you Require