Honda ► CB450K ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB450K with universal parts included►
- Honda
![Honda CB450K Front Brake Caliper Adjuster Set](/images/parts/100/29-7016.jpg)
Front Brake Caliper Adjuster Set
Front Brake Caliper Adjuster Set. Includes Adjusting Bolt, Spring, Washer and Nut.
![Honda CB450K Front Brake Caliper Bleed Screw](/images/parts/100/29-7017.jpg)
Front Brake Caliper Bleed Screw
Front Brake Caliper Bleed Screw. Replaces OEM # 45109-300-003
![Honda CB450K Brake Caliper Bleed Screw Rubber Cap (Stock Type)](/images/parts/100/29-7018.jpg)
Brake Caliper Bleed Screw Rubber Cap (Stock Type)
Stock Type Brake Caliper Bleed Screw Rubber Cap. These are the Same Design Rubber Caps as the Originals from the Factory. Replaces OEM # 45110-300-003 / 45224-579-013
![Honda CB450K Hydraulic Brake Light Switch](/images/parts/100/29-7021.jpg)
Hydraulic Brake Light Switch
Hydraulic Brake Light Switch - OEM Ref # 35350-300-006 / 35350-300-016 / 341-83980-30-00 10mm x M1.25 thread
![Honda CB450K Swingarm Pivot Bolt Locknut with Washer](/images/parts/100/29-7022.jpg)
Swingarm Pivot Bolt Locknut with Washer
Swingarm Pivot Bolt Locknut with Locknut Washer. Replaces OEM # 90354-268-000 (Locknut) and OEM # 90526-268-000 (Washer).
![Honda CB450K Swingarm Dust Seal Cap (Set/2)](/images/parts/100/29-7024.jpg)
Swingarm Dust Seal Cap (Set/2)
Swingarm Dust Seal Metal Cap (Set/2). These Metal Caps go on the Ends of the Swingarm Pivot. Replaces OEM # 52144-283-010 X2
![Honda CB450K Special Oil Filter Rotor Washer](/images/parts/100/29-7034A.jpg)
Special Oil Filter Rotor Washer
Special Angled Oil Filter Rotor Washer (16mm), Replaces OEM# 90481-292-000
![Honda CB450K Front Brake Rotor](/images/parts/100/30-3066.jpg)
Front Brake Rotor
Front Brake Rotor. Replaces OEM# 45120-392-000 / 45120-300-040 / 45120-341-000
![Honda CB450K Master Cylinder Rubber Boot](/images/parts/100/33-0003.jpg)
Master Cylinder Rubber Boot
Master Cylinder Rubber Boot. This Boot Attaches to where the Brake Hose Joins to the Master Cylinder. Replaces OEM # 45522-300-010
![Honda CB450K Ignition Switch Nut Tool](/images/parts/100/35-9119.jpg)
Ignition Switch Nut Tool
Ignition Switch Nut Tool, used to loosen and tighten the igntion switch nut properly without causing any damage to the switch.
![Honda CB450K Clutch Plate](/images/parts/100/39-1046B.jpg)
Clutch Plate
Clutch Plate 7 Piece Required OEM Ref # 22201-283-000 / 22201-MA7-000
![Honda CB450K Steel Clutch Plate](/images/parts/100/39-1409.jpg)
Steel Clutch Plate
Steel Clutch Plate 6 Pieces Required OEM Ref # 22321-283-000 / 22321-MG8-000
![Honda CB450K Carb Rebuild Kit](/images/parts/100/48-1395.jpg)
Carb Rebuild Kit
Carb Rebuild Kit for carburetor models 14H and 14L which were used on 5 speed 450's. There are several different carb models for the CB450 and CL450 so please make sure to check your carb model number before ordering. The main jet sizes in the later model carbs are larger. (#145 or #150) Note: Each Kit Rebuilds One Carb, Order the Quantity of Kits you Require
![Honda CB450K Carb Holder](/images/parts/100/48-1475.jpg)
Carb Holder
Carb Holder with Gasket - Replaces OEM# 16211-283-000 NOTE: This is for One Holder, These Bikes Use 2 Of These So Purchase 2 If Replacing Both Holders. If you require band clamps, this carb holder requires our carb holder clamp #15-0685
![Honda CB450K Float Needle & Seat](/images/parts/100/48-5009.jpg)
Float Needle & Seat
Float Needle & Seat High Quality - Made In Japan OEM Ref # 16011-302-004 / 16011-375-004
![Honda CB450K Float Bowl Drain Screw](/images/parts/100/48-5041.jpg)
Float Bowl Drain Screw
Float Bowl Drain Screw w O-Ring. Note: We sell these each, order the quantity you require
![Honda CB450K Seat Cover](/images/parts/100/48-9209.jpg)
Seat Cover
Replacement Seat Cover with Reinforced Passenger Strap (No trim or hardware included just re-use existing hardware). There is not a "Honda" stencil on the rear of the cover due to copyright. Each seat cover is made entirely by hand in North America, it is crafted slowly with great care by a gifted master upholster, using only the top grade materials available. Comes with complete installation instructions as well as step by step instructions on how to repair damaged seat foam. This is for the SEAT COVER, Not the Full Seat, Photo Shows Seat Cover Installed for reference
![Honda CB450K Side Cover Emblem](/images/parts/100/48-9508.jpg)
Side Cover Emblem
Cast Metal Side Cover Emblem with the 3 Attachment Clips for the rear of the emblem (You must use your old bolt and washers that attach at the front of the emblem). Replaces OEM # 87130-294-010 / 87130-319-671 / 87125-346-670 Note: There are a few different styles of side cover emblems used on these bikes. Be sure to verify this design is the type you need before purchasing. Note: 2 Emblems Used Per Bike, Order the Quantity you Require
![Honda CB450K Lens Screw](/images/parts/100/49-0144.jpg)
Lens Screw
Tail Light Lens Screws, Pack of 10. Replaces OEM # 93500-04050-4J ISO Std. Pitch - Steel Plated Size: 4 x 50mm
![Honda CB450K Shock Absorber Washer](/images/parts/100/49-0778.jpg)
Shock Absorber Washer
Shock Absorber Washer, Used when Installing Shocks. Replaces OEM # 90521-292-000 Note: Washers sold Each, order the quantity you require
![Honda CB450K Front Sprocket Lock Plate Set](/images/parts/100/49-0782.jpg)
Front Sprocket Lock Plate Set
Front Sprocket Lock Plate with 2 Lock Plate Bolts. It's Always good to replace these when installing a new front sprocket. Replaces OEM # 23811-292-000 (Plate) and OEM # 92101-06016-0A (Bolts) X2.
![Honda CB450K Steering Stem Nut](/images/parts/100/49-0786.jpg)
Steering Stem Nut
Chrome Steering Stem Nut, Hex Nut Size 30mm. Replaces OEM # 90304-415-000 Note: Sold Each, order the quantity your require
![Honda CB450K Steering Stem Washer](/images/parts/100/49-0787.jpg)
Steering Stem Washer
Chrome Steering Stem Washer, Replaces OEM # 90503-283-000 Sold Each, order the quantity you require.
![Honda CB450K Side Stand Spring](/images/parts/100/49-0788.jpg)
Side Stand Spring
Side Stand Spring, Replaces OEM # 95014-72402