Honda ► CB450K ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB450K with universal parts included that match “screws nuts bolts tools”►
- Honda
![Honda CB450K Spring Puller](/images/parts/100/35-0113.jpg)
Spring Puller
Spring Puller, Made from Heat Treated Alloy Steel. Great for Removing and Installing Those Hard to Reach Springs.
![Honda CB450K Bearing Packer](/images/parts/100/35-9122.jpg)
Bearing Packer
Wheel Bearing Grease Packer. To pack a bearing, place the bearing on the piston, press down on the cap until the old grease is forced out and the new grease shows on top of the bearing. Grease stays in the tool cavity, not on your hands. Transparent, impact resistant cup allows easy grease level checks. Works on bearings up to 3-1/2" OD or 89mm.
![Honda CB450K Flywheel Puller](/images/parts/100/35-0023.jpg)
Flywheel Puller
Flywheel Puller 27mm x 1.0 Left Hand Thread Internal Thread Flywheels & Rotors Honda - CR80R, CR125R, CR250R, CR450R, CR500R. Many Kaw/Suz/Yam
![Honda CB450K Flywheel Puller](/images/parts/100/35-0030.jpg)
Flywheel Puller
Flywheel Puller 20mm x 1.5 Right Hand Thread Internal Thread Flywheels & Rotors Honda - CB750 Four 69-78 SOHC Models, Suzuki - GSX-R600V, GSX-R750 T/V
![Honda CB450K Flywheel Puller](/images/parts/100/35-0031.jpg)
Flywheel Puller
Flywheel Puller 22mm x 1.5 Right Hand Thread Internal Thread Flywheels & Rotors Honda - XL250, XL350, XL600, XR600R, XR250, XR350, XR500
![Honda CB450K Flywheel Puller](/images/parts/100/35-0035.jpg)
Flywheel Puller
Flywheel Puller 18mm x 1.5 Right Hand Thread ( Hollow Center) Internal Thread Flywheels & Rotors Honda - 4 Cyl. Street 4-Valve Per Cylinder Engines CB750K, CB900C, CB1000 78 & Later
![Honda CB450K Flywheel Puller](/images/parts/100/35-0062.jpg)
Flywheel Puller
Flywheel Puller 35mm x 1.5 Right Hand Thread External Thread Flywheels & Rotors
![Honda CB450K Tire Lever - 16.5" Spoon Type w Handle](/images/parts/100/35-0063.jpg)
Tire Lever - 16.5" Spoon Type w Handle
Tire Lever - 16.5" Spoon Type, Forged Steel with Plastic Handle.
![Honda CB450K Brake Bleeder Hose Kit](/images/parts/100/35-0072.jpg)
Brake Bleeder Hose Kit
Brake Bleeder Hose Kit. Kit includes 1-way valve, hose and clamps. This tool helps bleed motorcycle brakes quickly and easily. The 1-way valve prevents air from flowing back into the brake lines. Easy to use, simply connect and pump.
![Honda CB450K Combination Flywheel Puller Driver Set](/images/parts/100/35-0074.jpg)
Combination Flywheel Puller Driver Set
10 Piece Combination Flywheel Puller Driver Set. Used to separate flywheel from the crankshaft taper. Supplied in a labelled plastic storage case. This 10 pieces set provides 15 different applications, sizes as follows: M14x1.5, M16x1.5, M18x1.5, M19x1.0, M20x1.0, M27x1.25, M22x1.0, M25x1.5, M22x1.5, M26x1.5, M24x1.0, M27x1.0, M26x1.0, M28x1.0, M28x1.5 Except for M27X1.0, all applications have right hand threads.
![Honda CB450K Digital Tire Gauge](/images/parts/100/35-0089.jpg)
Digital Tire Gauge
Digital Tire Pressure Gauge Measures 1-100 PSI (0.1 - 7.0 Bar)
![Honda CB450K Wheel Bearing Remover Set](/images/parts/100/35-0092.jpg)
Wheel Bearing Remover Set
8 Piece Metric Wheel Bearing Remover Set in a Plastic Case. Includes a large and small driver with 10mm, 12mm, 15mm, 17mm, 20mm and 25mm removers. Dependable split collet design.
![Honda CB450K Tire Inflator](/images/parts/100/35-9042.jpg)
Tire Inflator
Tire Inflator 3 Function Inflator 2" Dial Guage 0-160PSI / 0-11KPA 12" Hose With Chuck
![Honda CB450K Hose Remover Pliers](/images/parts/100/35-0049.jpg)
Hose Remover Pliers
Hose Remover Pliers. For easy removal of 5/32" to 1/2" hoses. The jaw digs into the tube to grip it, squeeze and the hose is easily pushed off by the jaw.
![Honda CB450K Blind Hole Bearing Puller Set](/images/parts/100/35-8010.jpg)
Blind Hole Bearing Puller Set
Blind Hole Bearing Puller Set Includes 2.15LB Slide Hammer With Shaft & 8 Pc Of Bearing Collets. Pulls The Following Size Bearings: 8-10mm, 10-12mm, 12-14mm, 15-17mm, 17-20mm, 20-24mm, 25-29mm, 30-32mm
![Honda CB450K 382pc O-Rings Kit with Plastic Case](/images/parts/100/35-0066.jpg)
382pc O-Rings Kit with Plastic Case
382pc O-Rings Kit with Plastic Case. 30 different sizes included in mm's. QTY---Width----Inside Dia.---------QTY---Width-----Inside Dia. 20X---1.78mm--2.90mm------------13X---2.62mm--9.19mm 20X---1.78mm--3.69mm------------13X---2.62mm--10.77mm 20X---1.78mm--4.47mm------------13X---2.62mm--12.37mm 20X---1.78mm--5.29mm------------13X---2.62mm--13.95mm 20X---1.78mm--6.07mm------------13X---2.62mm--15.54mm 20X---1.78mm--7.65mm------------13X---2.62mm--17.12mm 20X---1.78mm--9.25mm------------13X---2.62mm--18.72mm 10X---3.53mm--18.64mm----------10X---3.53mm--31.34mm 10X---3.53mm--20.22mm----------10X---3.53mm--32.92mm 10X---3.53mm--21.82mm----------10X---3.53mm--34.52mm 10X---3.53mm--23.39mm----------10X---3.53mm--36.10mm 10X---3.53mm--25.00mm----------10X---3.53mm--37.70mm 10X---3.53mm--26.57mm------------7X---5.34mm--37.47mm 10X---3.53mm--28.17mm------------7X---5.34mm--40.65mm 10X---3.53mm--29.75mm------------7X---5.34mm--43.82mm
![Honda CB450K 419pc O-Rings Kit with Plastic Case](/images/parts/100/35-0067.jpg)
419pc O-Rings Kit with Plastic Case
419pc O-Rings Kit with Plastic Case. 32 different sizes included metric sizes. QTY---Width----Inside Dia.---------QTY---Width-----Inside Dia. 20X---1.50mm--3.00mm------------13X---2.50mm--11.00mm 23X---1.50mm--7.00mm------------14X---2.50mm--13.00mm 23X---1.50mm--10.0mm------------13X---2.50mm--14.00mm 23X---1.50mm--13.0mm------------14X---2.50mm--16.00mm 20X---2.00mm--4.40mm------------14X---2.50mm--18.00mm 18X---2.00mm--5.00mm------------13X---2.50mm--19.00mm 14X---2.50mm--10.0mm------------14X---2.50mm--21.00mm 13X---2.50mm--22.00mm----------10X---3.50mm--31.00mm 10X---3.50mm--18.00mm----------10X---3.50mm--33.00mm 10X---3.50mm--20.00mm----------10X---3.50mm--34.50mm 10X---3.50mm--22.00mm----------10X---3.50mm--36.00mm 10X---3.50mm--23.50mm----------10X---3.50mm--38.00mm 10X---3.50mm--25.00mm----------10X---3.50mm--41.00mm 10X---3.50mm--26.50mm----------10X---3.50mm--44.00mm 10X---3.50mm--28.00mm----------10X---3.50mm--47.00mm 10X---3.50mm--30.00mm----------10X---3.50mm--50.00mm
![Honda CB450K Carb Float Level Gauge](/images/parts/100/35-0043.jpg)
Carb Float Level Gauge
Carburetor Float Level Gauge. Used to measure the float height between the float and carburetor gasket surface. It is important to make sure the float height is correct to factory spec when tuning your engine. Too little or too much fuel in the float bowl will negatively affect tuning results. Adjustable to fit most carburetors. Adjustable Width: 16-78mm and Adjustable Height 0-40mm
![Honda CB450K Permatex Valve Lapping Paste](/images/parts/100/35-0124.jpg)
Permatex Valve Lapping Paste
Valve Lapping Paste - Permatex Aids valve grinding and seating operations to remove burrs, surface defects, carbon and corrosion. Mixes with water to form an easy to use paste.
![Honda CB450K Adjustable Fork Seal Driver 35-45mm](/images/parts/100/35-3041.jpg)
Adjustable Fork Seal Driver 35-45mm
Adjustable 35-45mm Fork Seal Driver. This high quality tool can be used on many different fork sizes. Use these for easy installation of most fork seals on either conventional or inverted forks.
![Honda CB450K Front Signal Lamp Stay ~ Short Type](/images/parts/100/73-1105.jpg)
Front Signal Lamp Stay ~ Short Type
Front Signal Lamp Stay with Nut and Washer ~ Short Type - Chrome. These are M10 x 1.50 with nut - Ensure your bike requires this thread size before purchasing. Body Length 26mm, Thread 21mm, Total Length 47mm.
![Honda CB450K Bar Harness](/images/parts/100/27-5505.jpg)
Bar Harness
Bar Harness Eliminates Damage To Fairings, Grips & Body Covers Red Heavy Duty Nylon Web 1 3/4" x 37"
![Honda CB450K Black Tie Downs w/ Assist Carabiner](/images/parts/100/27-5515.jpg)
Black Tie Downs w/ Assist Carabiner
Black Heavy Duty Cam Buckle Tie Down (Set/2) w/ Assist Carabiner. Features a 3/8" diameter rubber coated hook, 1" wide straps with a length of 5.6 feet, non slip cam buckles with vinyl coating to protect chrome and paint. 1200lb Strength.
![Honda CB450K Magura Clutch Master Cylinder](/images/parts/100/08-0252.jpg)
Magura Clutch Master Cylinder
Magura Clutch Master Cylinder 16mm Piston Diameter Stroke 12mm Brake Switch (12-0002), Banjo Bolt (08-0254) and Banjo Bolt Washer (08-0258) Sold Separately.
![Honda CB450K Front Master Cylinder w Remote Reservoir - 14mm](/images/parts/100/08-0260.jpg)
Front Master Cylinder w Remote Reservoir - 14mm
Universal Front Brake Master Cylinder with a Remote Reservoir 14mm Piston Diameter Low Profile Design With 10 x 1.25 Threaded Outlet Comes With: Alloy Body, Adjustable Lever, Banjo Bolt Washers, Banjo Bolt.
![Honda CB450K Front Brake Master Cylinder](/images/parts/100/08-0262.jpg)
Front Brake Master Cylinder
Universal Front Brake Master Cylinder 13mm Piston Diameter Low Profile Design With 10 x 1.25 Threaded Outlet Comes With: Alloy Body, Alloy Lever, Brake Switch, Banjo Bolt Washers, Banjo Bolt.
![Honda CB450K Front Master Cylinder w Remote Reservoir - 16mm](/images/parts/100/08-0266.jpg)
Front Master Cylinder w Remote Reservoir - 16mm
Universal Front Brake Master Cylinder with a Remote Reservoir 16mm Piston Diameter Low Profile Design With 10 x 1.25 Threaded Outlet Comes With: Alloy Body, Adjustable Lever, Banjo Bolt Washers, Banjo Bolt.
![Honda CB450K Replacement Mirror](/images/parts/100/16-3024.jpg)
Replacement Mirror
Replacement Mirror - Fits Right or Left - Universal Fit Universal Rounded Rectangular Tinted Type 10mm Screw In Thread Chrome Plated
![Honda CB450K Replacement Mirror](/images/parts/100/16-3070.jpg)
Replacement Mirror
Replacement Mirror Kawasaki Z-1 Style 4 3/8" Round Mirror With Oval Back 10mm Screw Mount. 6" Long Stem
![Honda CB450K LED Turn Signal Set/2](/images/parts/100/12-0131.jpg)
LED Turn Signal Set/2
Custom LED Turn Signal Set/2. 3.5" Long Turn Signals with 10" Long Wires, DC 12 Volt. Will screw on to 10mm Screw holes. 2 Wire (Signal and Ground). These Require an LED relay to work. We sell these #12-0130
![Honda CB450K Custom LED Turn Signal Set/2](/images/parts/100/12-0132.jpg)
Custom LED Turn Signal Set/2
Custom LED Amber Lens Turn Signal Set/2. 2.5" Long Turn Signals with 10.5" Long Wires, DC 12 Volt. Will screw on to 8mm Screw holes. 2 Wire (Signal and Ground). These Require an LED relay to work. We sell these #12-0130
![Honda CB450K TC Bros. Universal Linkage Kit](/images/parts/100/73-1164.jpg)
TC Bros. Universal Linkage Kit
TC Bros. Brand Universal Linkage Kit for all TC Bros. Forward Control Kits. The rods/tubes will need to be cut to fit your application. Kit includes, Two 24" Long 5/16" Threaded Rods, Four 5/16" Ball Joints, Two 5/16" ID x 1/2" OD Steel Tubes* (to cover rod threads and increase rigidity), Eight 5/16" Jam Nuts, Four Nylock Nuts and Four Flat Washers. This Set is needed for all the forward control kits we carry
![Honda CB450K Universal Fuel Petcock](/images/parts/100/20-0100.jpg)
Universal Fuel Petcock
Universal Fuel Petcock On/Off/Reserve Positions One straight Outlet Fitting, Two ninety degree outlet fittings & One outlet blockoff plug included. Direct fit to 3/8" NPT (Female Thread) in tank or choose adaptor plate or Nut as required.
![Honda CB450K Magura Brake Master Cylinder (13mm)](/images/parts/100/08-0250.jpg)
Magura Brake Master Cylinder (13mm)
Magura Front Brake Master Cylinder 13mm Piston Diameter - Recommended For Single Disk System Stroke 12mm, Thread for Brake Light Switch Brake Switch (12-0002), Banjo Bolt (08-0254) and Banjo Bolt Washer (08-0258) Sold Separately.
![Honda CB450K Magura Brake Master Cylinder (16mm)](/images/parts/100/08-0251.jpg)
Magura Brake Master Cylinder (16mm)
Magura Front Brake Master Cylinder 16mm Piston Diameter - Recommended For Dual Disk System Thread for Brake Light Switch Brake Switch (12-0002), Banjo Bolt (08-0254) and Banjo Bolt Washer (08-0258) Sold Separately.
![Honda CB450K Clutch Master Cylinder Assembly](/images/parts/100/08-0261.jpg)
Clutch Master Cylinder Assembly
Clutch Master Cylinder with 12.9mm Piston Diameter - Comes With: Alloy Body, Alloy Lever, Banjo Bolt Washers, Banjo Bolt and brake/clutch switch. Quality low profile design with a 10 x 1.25 Front threaded outlet.