Honda ► CB450K ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB450K with universal parts included that match “1”►
- Honda
Front/Rear Signal Lamp ~ 1 Wire Type
Signal Lamp - Amber - 12v - 1 wire for Front or Rear - Replaces OEM# 33600-447-000 / 33600-447-P00. Please double check you require the 1 wire type before purchasing Stem *Our Part Number 11-2167*
Wheel Seal Kit
Rear Wheel Seal Kit 1 Seal 34 x 55 x 9
Starter Motor Seal
Starter Motor Seal - 60 x 1.4 - Replaces OEM# 31206-286-158 / 31206-402-008
Replacement Mirror
Replacement Mirror (R.H) 4 1/2" Diameter, 10mm Thread. Replaces OEM# 88110-333-611
Replacement Mirror
Replacement Mirror (L.H) 4 1/2" Diameter, 10mm Thread. Replaces OEM# 88120-333-611
Gear Change Lever
Gear Change Lever Universal Fit Spline Diameter 11.5mm Total Length 6 1/2" Offset 4"
Fork Gaiters
Fork Gaiters OEM Ref # 51611-300-000 Note: These are about 1.75" shorter then the stock type but will work fine
Exhaust Gasket (Each)
Exhaust Gasket - 1 Pc OEM Ref # 18291-283-010 / 18291-ME9-000 / 18291-MM8-880 Sold Each, Order the Quantity you Require
Front Brake Caliper Piston
Front Brake Caliper Piston (1) - 38.15mm Diameter x 34mm Height - Replaces OEM # 45107-323-020. Please note: the side with the 2mm outer lip faces the brake pad during install.
Fuel Petcock
Fuel Petcock - Replaces OEM # 16950-292-000 - Fits M16 x 1.5 Note: Please Check that the Size Listed Above is Correct for your Bike before ordering
Hydraulic Brake Light Switch
Hydraulic Brake Light Switch - OEM Ref # 35350-300-006 / 35350-300-016 / 341-83980-30-00 10mm x M1.25 thread
Stock Type Front Reflector Rubber Base
Stock Type Front Reflector Rubber Base - Replaces OEM# 33743-341-670
Front Wheel Bearing Retainer Ring Tool
Front Wheel Bearing Retainer Ring Tool. High quality tool for removing and fitting the front wheel bearing retainer ring with 1/2 inch socket bar wrench tool hole. The perfect tool for easier removal and fitting without damaging the special retainer ring.
Steering Stem Nut
Chrome Steering Stem Nut, Hex Nut Size 30mm. Replaces OEM # 90304-415-000 Note: Sold Each, order the quantity your require
Steering Stem Washer
Chrome Steering Stem Washer, Replaces OEM # 90503-283-000 Sold Each, order the quantity you require.
Joker Machine Magnetic Oil Drain Plug
Joker Machine Magnetic Oil Drain Plug with O-Ring, Replaces OEM# 90013-312-000. High quality made from 6061 billet aluminum. High power rare earth neodymium-iron boron magnet pressed into the body that exceptionally grabs steel debris from your tank and motor. M33.7 - 1.5mm thread pitch. Installs with a 19mm socket. - 45mm outside diameter and 19mm off the case.
Custom Black Gas/Fuel Tank Cap ~ Joker Machine
Joker Machine Brand ~ Custom Black Gas/Fuel Tank Flip Up Billet Cap. Includes Cap with a spring loaded alloy flange, replaceable rubber gasket and alloy screw attachment. Replaces OEM # 17510-323-310 Installs easily onto the tank hinges with an alloy screw (not rivets found on the stock set-up) in minutes. Lightweight design is made from a solid block of 1" thick Billet aluminum. Works with stock style latching mechanisms (Sold Separately). High quality CNC machined cap made in the U.S.A.
Black Steering Stem Nut ~ Joker Machine
Joker Machine Brand ~ Black Steering Stem Nut, Hex Nut Size 30mm. Replaces OEM # 90304-415-000 High quality CNC machined part made in the U.S.A.
Bar Switch Assembly ~ Left (Clutch) Side
Bar Switch Assembly ~ Left (Clutch) Side - Black. Replaces OEM # 35250-300-033
Front Brake Caliper Bleed Screw
Front Brake Caliper Bleed Screw. Replaces OEM # 45224-579-013
Cylinder Head Gasket
Cylinder Head Gasket, Replaces OEM# 12909-428-003 / 12909-283-000 / 12909-333-000.
Headlight Setting Collar
Headlight Setting Collar, Replaces OEM# 61304-292-000 Sold Each, order the quantity you require
Honda OEM Type Grips
Honda OEM Type Rubber Grip Set - Black - Closed end type for 7/8" bars. These are replica's of the original type grips from the factory. 135mm Length. Replaces OEM #' 53165-342-670 / 53166-342-670
Brake Lever ~ GP Style
Brake Lever - Custom GP Style in Silver, This Has More of a Bend/Kickback then the stock lever. Replaces OEM # 53175-369-003
Starter / Horn Button
Starter / Horn Button
High Performance Kibblewhite Bronze Swingarm Bushing Set
High Performance Kibblewhite Bronze Swingarm Bushing Set/2. Replaces OEM# 52108-457-300, 52108-422-300. Made in the USA by Kibblewhite who have been making High Quality Performance parts for 75+ years. Kibblewhite bronze bushings offers increased durability and better fitment then the OEM type bushings.
Master Cylinder Rubber Boot
Master Cylinder Rubber Boot. This Boot Attaches to where the Brake Hose Joins to the Master Cylinder. Replaces OEM # 45522-300-010
Speedometer Cable
Speedometer Cable - Black - OEM Ref. # 44830-425-870 End to End Length 38.5" Made in Japan
Rear Shock Swingarm Bushing
Rear Shock Swingarm Bushing, Replaces OEM# 40548-268-000 19mm Long, 22mm OD, 10mm ID. Sold Each, Order the Quantity you Require
Speedo Gear Plug
Speedo Gear Plug - Plug 15mm Outer Diameter, 22mm Long. This Plug is Great for Keeping your Original Speedo Drive Gear Clean.
Tail Light Lens
Tail Light Lens OEM Ref # 33702-341-671
Handlebar Clutch Lever Pivot Bolt & Nut Set
Handlebar Clutch Lever Pivot Bolt & Nut Set. This is the Set that Fastens the Clutch Lever in Place. Includes One Bolt with One Nut. Replaces OEM # 90114-310-000 (Bolt) and OEM # 94001-06200-0S (Nut).
Brake Rod Joint
Brake Rod/Arm Joint, Replaces OEM # 95015-32001
Front Wheel Bearing Retainer
Front Wheel Bearing Retainer - Replaces OEM# 44643-300-000
Seat Lock with Keys
Seat Lock with Keys, Replaces OEM # 77230-399-007 / 77230-107-711 This seat lock works perfect for the bikes listed but the locking mechanism sticks out a bit farther then the OEM type. If you have lost your old key you have to remove the seat lock bracket and assembly. This can be done with a short 10mm wrench or socket, once that's done the rest is easy.
Turn Signal Lamp Gasket
Turn Signal Lamp Gasket, Replaces OEM # 33443-268-671
Stop Light Switch
Rear Stop Light Switch OEM Ref # 35350-292-003 / 35350-KJ9-405
Handlebar Clamp Set /2
Black Handlebar Clamp Set/2. These clamp the stock 7/8" handlebars to the upper triple clamp. Replaces OEM # 95014-22200
Seat Rubber "B"
Seat Setting Rubber "B". This is one of the Rubber Settings Under the Seat. Replace those old worn Rubbers with a brand new one! Replaces OEM # 77205-286-000 Order the Quantity of Seat Rubber "B" your Bike Requires
Brake Rod Spring
Brake Rod Spring. Replaces OEM # 95014-73100
Rim Lock 1.60"
Rim Lock 1.60" Rim, All Strong Rubber Type. Rim Lock / Bead Lock fits to 1.60" rims (for most tire sizes 250-300). Are you popping tubes quickly? A rim lock, or "bead lock" may be exactly what you need. A rim lock secures the tire, to reduce the chance of tire slippage on the rim, ultimately protecting the inner tube. Eliminates tube pinching and casing damage!
Rim Lock 1.85"
Rim Lock 1.85" Rim, All Strong Rubber Type. Rim Lock / Bead Lock fits to 1.85" rims (for most tire sizes 325-350). Are you popping tubes quickly? A rim lock, or "bead lock" may be exactly what you need. A rim lock secures the tire, to reduce the chance of tire slippage on the rim, ultimately protecting the inner tube. Eliminates tube pinching and casing damage!
Mounting Clamp ~ Chrome ~ 1" Bars
Chrome Speedo/Tach/Mirror Mounting Clamp 2 Piece Die-Cast Alloy Clamp With 10mm RH Thread Fits 1" Bars
Heavy Duty Rim Lock 1.85"
Rim Lock 1.85" Rim Type, Heavy Duty Metal Base Covered with Strong Rubber. Rim Lock / Bead Lock fits to 1.85" rims (for most tire sizes 325-350). Are you popping tubes quickly? A rim lock, or "bead lock" may be exactly what you need. A rim lock secures the tire, to reduce the chance of tire slippage on the rim, ultimately protecting the inner tube. Eliminates tube pinching and casing damage!
Stud Extractor 1-6mm
Stud Extractor 1/4" Drive, used to remove seized or broken studs and bolts. Designed to fit into small areas, where studs may be hard to reach. Use with an impact wrench. Fits studs from (1-6mm)
Black Single Cable Pull Throttle Assembly 1"
Black Single Cable Pull Throttle Assembly For 1" Bars Jackhammer Style 140mm Length Grips Features Tension Adjuster and Built in Cable Adjustment High Quality Black Powder Coated Aluminum Housing and Aluminum Throttle Tube
Standard Double Banjo Bolt ~ M10 X 1.0
M10 X 1.0 (Fine Thread) Standard Double Banjo Bolt with Washers ~ used when stacking 2 lines. 32mm length to bottom of bolts head. High Quality Stainless Steel
Standard Double Banjo Bolt ~ M10 X 1.25
M10 X 1.25 - Standard Double Banjo Bolt with Washers ~ used when stacking 2 lines. 32mm length to bottom of bolts head. High Quality Stainless Steel
Custom Bates Style 4 1/2" Black Bottom Mount Headlight
Custom Bates Style 4 1/2" Satin Black Bottom Mount Headlight. Glass sealed beam with a P15D base, 12 volt 35/35 watt bulb, 16" wire leads. Blue dot high/low beam indicator on top of light housing.
Fuel Hose Quick Disconnect - 1/4" 6mm Fuel Line
Fuel Hose Quick Disconnect - For 1/4" or 6mm fuel line. Fuel line cut off for a quick and easy way to cut off fuel supply while working on your bike.