Honda ► CB500 ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB500 with universal parts included that match “1”►
- Honda
Oil Filter
Oil Filter OEM Ref # 15412-413-005 / 154A1-413-005 / 154A1-MA6-000
Gear Change Lever
Gear Change Lever Universal Fit Spline Diameter 11.5mm Total Length 5 1/8" Offset 1 3/8"
Turn Signal Lamp
Turn Signal Lamp 1-Wire - Rear OEM Ref # 33400-377-671 / 33400-460-671 / 33400-460-679
Carb Rebuild Kit
Carb Rebuild Kit Includes Items Pictured High Quality - Made In Japan 1 Kit Needed Per Carb
Starter Brush Set
Starter Brush Set/2 1Pc Insulated Leads 1Pc Non-Insulated Leads 12mm x 14mm x 6mm For Misuba 2 Brush Starter. OEM Ref # 31201-292-158 / 31201-MG9-004
Front Brake Caliper Piston
Front Brake Caliper Piston (1) - 38.15mm Diameter x 34mm Height - Replaces OEM # 45107-323-020. Please note: the side with the 2mm outer lip faces the brake pad during install.
Hydraulic Brake Light Switch
Hydraulic Brake Light Switch - OEM Ref # 35350-300-006 / 35350-300-016 / 341-83980-30-00 10mm x M1.25 thread
Steering Stem Nut
Chrome Steering Stem Nut, Hex Nut Size 30mm. Replaces OEM # 90304-415-000 Note: Sold Each, order the quantity your require
Steering Stem Washer
Chrome Steering Stem Washer, Replaces OEM # 90503-283-000 Sold Each, order the quantity you require.
Fuel Petcock Screen
Replacement Fuel Petcock Screen for the stock type fuel petcock. Replaces OEM# 16957-268-010
Swingarm Dust Seal Cap (Set/2)
Swingarm Dust Seal Metal Cap (Set/2). These Metal Caps go on the Ends of the Swingarm Pivot. Replaces OEM # 52144-283-010 X2
Fuel Petcock Gasket
Fuel Petcock Gasket. Replaces OEM # 16955-268-020
Bar Switch Assembly ~ Left (Clutch) Side
Bar Switch Assembly ~ Left (Clutch) Side - Black. Replaces OEM # 35250-300-033
Front Brake Caliper Bleed Screw
Front Brake Caliper Bleed Screw. Replaces OEM # 45224-579-013
Master Cylinder Rubber Boot
Master Cylinder Rubber Boot. This Boot Attaches to where the Brake Hose Joins to the Master Cylinder. Replaces OEM # 45522-300-010
Oil Passage Cap with O-Ring
Oil Passage Cap with O-Ring. Replaces OEM # 15331-300-000 (Oil Passage Cap) and OEM # 94608-40000 (O-Ring). Note: Sold Each, Order the Quantity of Caps you Require
Rear Shock Swingarm Bushing
Rear Shock Swingarm Bushing, Replaces OEM# 40548-268-000 19mm Long, 22mm OD, 10mm ID. Sold Each, Order the Quantity you Require
Tail Light Lens
Tail Light Lens OEM Ref # 33702-341-671
Handlebar Clutch Lever Pivot Bolt & Nut Set
Handlebar Clutch Lever Pivot Bolt & Nut Set. This is the Set that Fastens the Clutch Lever in Place. Includes One Bolt with One Nut. Replaces OEM # 90114-310-000 (Bolt) and OEM # 94001-06200-0S (Nut).
Throttle Sleeve
Nylon Throttle Sleeve - Replaces OEM # 53141-300-010
Center Stand Spring
Center Stand Spring. Replaces OEM # 95014-71702
Neutral Switch
Neutral Switch, Replaces OEM # 35600-KE8-003
Flange Knock Bolt (Set/2)
Flange Knock Bolt (Set/2). These Bolts Fasten to the Cam Sprocket. Replaces OEM # 90082-HA0-000
Brake Rod Spring
Brake Rod Spring. Replaces OEM # 95014-73100
Rim Lock 1.60"
Rim Lock 1.60" Rim, All Strong Rubber Type. Rim Lock / Bead Lock fits to 1.60" rims (for most tire sizes 250-300). Are you popping tubes quickly? A rim lock, or "bead lock" may be exactly what you need. A rim lock secures the tire, to reduce the chance of tire slippage on the rim, ultimately protecting the inner tube. Eliminates tube pinching and casing damage!
Rim Lock 1.85"
Rim Lock 1.85" Rim, All Strong Rubber Type. Rim Lock / Bead Lock fits to 1.85" rims (for most tire sizes 325-350). Are you popping tubes quickly? A rim lock, or "bead lock" may be exactly what you need. A rim lock secures the tire, to reduce the chance of tire slippage on the rim, ultimately protecting the inner tube. Eliminates tube pinching and casing damage!
Mounting Clamp ~ Chrome ~ 1" Bars
Chrome Speedo/Tach/Mirror Mounting Clamp 2 Piece Die-Cast Alloy Clamp With 10mm RH Thread Fits 1" Bars
Heavy Duty Rim Lock 1.85"
Rim Lock 1.85" Rim Type, Heavy Duty Metal Base Covered with Strong Rubber. Rim Lock / Bead Lock fits to 1.85" rims (for most tire sizes 325-350). Are you popping tubes quickly? A rim lock, or "bead lock" may be exactly what you need. A rim lock secures the tire, to reduce the chance of tire slippage on the rim, ultimately protecting the inner tube. Eliminates tube pinching and casing damage!
Stud Extractor 1-6mm
Stud Extractor 1/4" Drive, used to remove seized or broken studs and bolts. Designed to fit into small areas, where studs may be hard to reach. Use with an impact wrench. Fits studs from (1-6mm)
Black Single Cable Pull Throttle Assembly 1"
Black Single Cable Pull Throttle Assembly For 1" Bars Jackhammer Style 140mm Length Grips Features Tension Adjuster and Built in Cable Adjustment High Quality Black Powder Coated Aluminum Housing and Aluminum Throttle Tube
Standard Double Banjo Bolt ~ M10 X 1.0
M10 X 1.0 (Fine Thread) Standard Double Banjo Bolt with Washers ~ used when stacking 2 lines. 32mm length to bottom of bolts head. High Quality Stainless Steel
Standard Double Banjo Bolt ~ M10 X 1.25
M10 X 1.25 - Standard Double Banjo Bolt with Washers ~ used when stacking 2 lines. 32mm length to bottom of bolts head. High Quality Stainless Steel
Custom Bates Style 4 1/2" Black Bottom Mount Headlight
Custom Bates Style 4 1/2" Satin Black Bottom Mount Headlight. Glass sealed beam with a P15D base, 12 volt 35/35 watt bulb, 16" wire leads. Blue dot high/low beam indicator on top of light housing.
Fuel Hose Quick Disconnect - 1/4" 6mm Fuel Line
Fuel Hose Quick Disconnect - For 1/4" or 6mm fuel line. Fuel line cut off for a quick and easy way to cut off fuel supply while working on your bike.
Universal 1 Ohm Dual Output 6V Ignition Coil
Universal 1 Ohm Dual Output 6V Ignition Coil. Will work on a number of Honda, Kawasaki, Suzuki, Yamaha, Norton, BSA, Triumph and other motorcycles with 6 volt dual output ignition coils. Check the coil mount spacing on your bike before you order. Mounting holes are 90mm (3.5") apart center to center. Low tension wires 390mm (15") long. Female spade connectors at the coil and male and female bullet connectors at the other ends. Spark plug wires (high tension leads) 570mm (24") long with 300mm (12") protective sheath.
Universal 1" Push/Pull Harley Style Chrome Twist Grip Throttle
Universal 1" Push/Pull Harley Style Chrome Twist Grip Throttle Assembly. Chromed aluminum housing with plastic throttle tube, pre-installed throttle assembly grip. Throttle is 5 1/4" long over all. Throttle tube is 4" long. Housing is 2" in diameter. Fits: 1" handle bars. For use with dual cable set ups.
CNC Machined Black Anodized 1/4" Fuel Filter w Clips
CNC Machined Aluminum Fuel Filter with 2 Clips, Black Anodized Type with Cleanable and Reuseable Brass Filter Element. 3" Long, 1/4" Fitting.
90 Degree Bronze Inline Fuel Filter ~ 1/4"
90 Degree Inline Fuel Filter with 1/4" Fitting. Features a premium bronze porous cleanable filter.
Chrome Bungee Nut Set/2 ~ 6mm x 1.00mm
New chrome pair of grooved Bungee Nuts 6mm x 1.00mm. Can work as a tie down knob, spring anchor or a simple way to attach bungee cords or cargo nets.
Chrome Bungee Nut Set/2 ~ 8mm x 1.25mm
New chrome pair of grooved Bungee Nuts 8mm x 1.25mm. Can work as a tie down knob, spring anchor or a simple way to attach bungee cords or cargo nets.
Chrome Bungee Nut Set/2 ~ 10mm x 1.25mm
New chrome pair of grooved Bungee Nuts 10mm x 1.25mm. Can work as a tie down knob, spring anchor or a simple way to attach bungee cords or cargo nets.
Carb Rebuild Shop Kit - 5mm x 1,200 Bolt/Washer Assortment
1202 Piece Stainless Steel Socket Head Bolt Set with Plastic Case. All the screws you typically need when rebuilding carbs that require 5mm machine screws. This includes the carbs found on many Kawasaki KZ, Suzuki GS, Yamaha XS models with CV carbs. Includes Sizes 5X8, 5X10, 5X12, 5X14, 5X16, 5X18
Valve Lapping Stick
Valve Lapping Stick 1 1/8" & 1 3/8" Cups
Muffler Clamp
Muffler Clamp - Universal Fits 1 1/2"
Foot Pegs
Chromed Foot Pegs Pk/2 Rubber Inlay 1" & 1 1/4" Clamp Universal Fit
Universal Glas-Pak Insert
Universal Glas-Pak Insert - Fits 1 1/2" Pipes - Glass Pak's Actual Size 1 3/8" Tone down your TT or Drag Pipes
Custom Ribbed Chrome Crash Bar Highway Footpeg Set
Custom Ribbed Chrome Crash Bar Highway Footpeg Set/2. 1" & 1 1/4" Clamp.
Custom Pebble Chrome Crash Bar Highway Footpeg Set
Custom Pebble Chrome Crash Bar Highway Footpeg Set/2. 1" & 1 1/4" Clamp.
Custom Honda Chrome Crash Bar Highway Footpeg Set
Custom Honda Chrome Crash Bar Highway Footpeg Set/2. 1" & 1 1/4" Clamp.
Custom Striped Rubbed Chrome Crash Bar Highway Footpeg Set
Custom Striped Rubbed Chrome Crash Bar Highway Footpeg Set/2 with Striped Rubber Inlay. 1" & 1 1/4" Clamp.