Honda ► CB500K ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB500K with universal parts included►
- Honda
Fuel Petcock
Fuel Petcock OEM Ref # 16950-300-020
Fuel Petcock Screen
Replacement Fuel Petcock Screen for the stock type fuel petcock. Replaces OEM# 16957-268-010
Steel Front Sprocket - 17 Tooth X 530
Steel Front Sprocket - 17 Tooth - Replaces OEM # 23801-300-010 For 530 Chain Setup as came stock with the bikes below. Fits: FRONT on Honda CB750K (1969-70) - Use from Engine # 1003528 or Higher, CB750F (1975-76) Supersport, CB750A (1976) Hondamatic Please Count your sprocket teeth and check your chain length before ordering to ensure this is correct for your bike
Rectifier/Regulator ~ Lithium Ion Battery Compatible
Rick's Electric Brand Lithium Ion Battery Compatible Rectifier-Regulator. Designed with a lower voltage set point to work with lithium ion batteries only. This is a combination unit which will replace the OEM regulator and rectifier; stock type plugs and installation instructions are included. Dimensions 70mm Length, 94mm Width, 27mm Height, Hole Distance 80mm Center to Center. Note: May require a custom mounting job. High quality Part. This is Not for use with standard lead acid batteries. The voltage set point is 14V +/- .2. Please ensure this set point is correct for your battery before attempting installation.
Starter Brush Set
Starter Brush Set/2 1Pc Insulated Leads 1Pc Non-Insulated Leads 12mm x 14mm x 6mm For Misuba 2 Brush Starter. OEM Ref # 31201-292-158 / 31201-MG9-004
Rectifier/Regulator
Rick's Electric Brand OEM Style Honda Rectifier-Regulator: This is a combination unit which will replace the OEM regulator and rectifier; stock type plugs and installation instructions are included. Dimensions 68mm Length, 94mm Width, 26mm Height, Hole Distance 80.0mm Center to Center. High quality Part. Note: May require a custom mounting job. Works great if attached with one bolt and nut where the safety starter switch was originally located (can bypass that switch).
Condenser
Condenser OEM Ref # 30250-300-154 / 30250-300-005
Fork Seals
Fork Seals Set/2 35 X 48 X 10.5/11
Stock Type Fork Gaitors
Black Stock Type Fork Gaitors (Set/2) OEM Ref. # 51611-300-000
Fork Gaiters
Fork Gaiters OEM Ref # 51611-300-000 Note: These are about 1.75" shorter then the stock type but will work fine
Swing Arm Bushing Set
Swing Arm Bushing Set/2. OEM Ref # 52108-300-300 Note: These Replace the factory plastic OEM Type Bushings.
Front Wheel Bearing Retainer
Front Wheel Bearing Retainer - Replaces OEM# 44643-300-000
Rear Wheel Bearing
Rear Wheel Bearing with 2 Synthetic Shields - 6305-2RS Size Replaces OEM# 96140-63050-10 High Quality Made in Japan
Billet Aluminum Upper Triple Tree Clamp
Custom Billet Aluminum Machined Upper Triple Tree Clamp. This billet triple has 2X 6mm mounting bosses 50mm apart on the underside of the top triple to accommodate various aftermarket and custom designed instrument mounts for your aftermarket gauges. Designed so the top triple has a rounded top edge with a stylish inset and makes an excellent replacement for the stock cast item when using clip-on bars! This piece was designed to make it very easy for the average Cafe builder to modify their motorcycle. Very High quality, machined in North America. Clip on bars not included and your stock bars will NOT mount to this piece.
Rear Shock Swingarm Bushing
Rear Shock Swingarm Bushing, Replaces OEM# 40548-268-000 19mm Long, 22mm OD, 10mm ID. Sold Each, Order the Quantity you Require
Engine Cover Bolt Set
High Quality Premium Stainless Steel Engine Cover Bolt Set Set includes: 57 Bolts, 11 Washers and 2 Allen keys for a total of 70 pieces. These bolts are all smooth head Allen bolts and are for the cylinder head cover, the left and right engine covers - points, clutch, alternator, sprocket and starter motor covers. The washers go under 8 of the cylinder head cover screws with washers from the factory, and one of the alternator cover screws, and the two starter motor cover screws.
Master Cylinder Reservoir Cap
Master Cylinder Cap with Plastic O-Ring. Replaces OEM # 45513-341-771 This style of master cylinder cap was discontinued long ago by Honda. We have had these produced again to keep your bike looking sharp. Spruce up your Master Cylinder with one of these great looking master cylinder caps!
Front Brake Caliper Piston
Front Brake Caliper Piston (1) - 38.15mm Diameter x 34mm Height - Replaces OEM # 45107-323-020. Please note: the side with the 2mm outer lip faces the brake pad during install.
Master Cylinder Reservoir Cap Plastic O-Ring
Master Cylinder Reservoir Cap Plastic O-Ring, Replaces OEM # 45521-MJ6-006
Reservoir Cap & Diaphragm
Reservoir Cap & Diaphragm Round Thread On Type OEM Ref # 43515-MJ6-006 / 45520-300-000
Cotter Valve / Valve Keeper
Cotter Valve / Valve Keeper, Replaces OEM# 14781-107-003 / 14781-107-020. 2 Used For Each Valve Spring. Sold Each, Order the Quantity you Require
Front Brake Caliper Piston Sealing Ring
Front Brake Caliper Piston Sealing Ring, Replaces OEM # 45108-300-003
Speedo Gear Plug
Speedo Gear Plug - Plug 15mm Outer Diameter, 22mm Long. This Plug is Great for Keeping your Original Speedo Drive Gear Clean.
Carburetor Stabilizer Bracket
Carburetor Stabilizer Bracket. These high quality made in Canada stainless steel brackets stabilize the carburetors when the air box is removed. A must have for pods or hard tails!
Rear Brake Shoes
Rear Brake Shoes Pk/2 Diameter: 178.5mm Width: 30mm OEM Ref # 43120-283-670
Front Brake Pads
Front Brake Pads Pk/2 OEM Ref # 45105-390-006A
Tachometer Cable Clamp
Chrome Tachometer Cable Clamp (Holder). Replace that Old Rusted, Worn Out Clamp with a Brand New Great Looking Chrome Tach Cable Clamp. Replaces OEM # 50462-323-010
Brake Rod Spring
Brake Rod Spring. Replaces OEM # 95014-73100
Headlight Adjusting Screw & Spring Set
Headlight Adjusting Screw & Spring Set. Each Set Includes One Screw and One Spring. Replaces OEM # 33103-346-670 (Screw) and OEM # 33107-300-003 (Spring)
Front Brake Caliper Adjuster Set
Front Brake Caliper Adjuster Set. Includes Adjusting Bolt, Spring, Washer and Nut.
Brake Caliper Bleed Screw Rubber Cap (Stock Type)
Stock Type Brake Caliper Bleed Screw Rubber Cap. These are the Same Design Rubber Caps as the Originals from the Factory. Replaces OEM # 45110-300-003 / 45224-579-013
Flange Knock Bolt (Set/2)
Flange Knock Bolt (Set/2). These Bolts Fasten to the Cam Sprocket. Replaces OEM # 90082-HA0-000
Hydraulic Brake Light Switch
Hydraulic Brake Light Switch - OEM Ref # 35350-300-006 / 35350-300-016 / 341-83980-30-00 10mm x M1.25 thread
Swingarm Pivot Bolt Locknut with Washer
Swingarm Pivot Bolt Locknut with Locknut Washer. Replaces OEM # 90354-268-000 (Locknut) and OEM # 90526-268-000 (Washer).
Swingarm Dust Seal Cap (Set/2)
Swingarm Dust Seal Metal Cap (Set/2). These Metal Caps go on the Ends of the Swingarm Pivot. Replaces OEM # 52144-283-010 X2
Tail Light Mounting Hardware Set
Tail Light Mounting Hardware Set. This Set is Used to Mount the Tail Light Bracket. This 12pc Set Includes 4pc Tail Light Setting Bolts, 4pc Tail Light Setting Washer and 4pc Rubber Fender Cushion.
Fuel Petcock Gasket
Fuel Petcock Gasket. Replaces OEM # 16955-268-020
Master Cylinder Rubber Boot
Master Cylinder Rubber Boot. This Boot Attaches to where the Brake Hose Joins to the Master Cylinder. Replaces OEM # 45522-300-010
Center Stand Spring
Center Stand Spring. Replaces OEM # 95014-71702
Ignition Switch Nut Tool
Ignition Switch Nut Tool, used to loosen and tighten the igntion switch nut properly without causing any damage to the switch.
Clutch Spring Set
Clutch Spring Set
Clutch Plate
Clutch Plate 7 Pieces Required OEM Ref # 22201-KY2-000 / 22201-MA6-000 / 22201-MN4-000 / 22201-MT6-601
Steel Clutch Plate
Steel Clutch Plate B OEM Ref # 22321-KA4-700 Order the Quantity you require
Carb Fuel Line O-Ring Kit
Carb Fuel Line O-Ring 12Pc Kit Includes: 8 Carb Fuel Connector Tube O-Rings and 4 Float Bowl Drain Seal Connector Tube O-Rings (The 4 tubes that connect the 4 carbs together).
Float Bowl Drain Screw O-Rings Pk/4
Float Bowl Drain Screw O-Rings Pk/4
Carb Holder Set
Carb Holder Set (Set of 4) - Replace those old cracked or dried up carb holders with a brand new set! Replaces OEM# 16211-323-000 If you require band clamps, these carb holders require our 41-44mm diameter clamps part #15-0684 X8.
Float Needle & Seat
Float Needle & Seat High Quality - Made In Japan OEM Ref # 16011-329-004
Float Bowl Drain Screw
Float Bowl Drain Screw w O-Ring. Note: We sell these each, order the quantity you require
Air Screw Needle O-Ring
Air Screw Needle O-Ring. 2.8mm x 1.2mm. Note: sold each, order the quantity you require
Lens Screw
Tail Light Lens Screws, Pack of 10 Screws. Replaces OEM # 93500-04055-4J ISO Std. Pitch - Steel Plated Size: 4 x 55mm