Honda ► CB500K ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB500K with universal parts included that match “honda sl125”►
- Honda
Oil Filter Bolt
Oil Filter Bolt OEM Ref # 15420-300-020
Speedo Gear Plug
Speedo Gear Plug - Plug 15mm Outer Diameter, 22mm Long. This Plug is Great for Keeping your Original Speedo Drive Gear Clean.
Rear Fuel Tank Holder Rubber
Rear Fuel Tank Holder Rubber, Replaces OEM# 17613-286-000
Front Sprocket Lock Plate Set
Front Sprocket Lock Plate with 2 Lock Plate Bolts. It's Always good to replace these when installing a new front sprocket. Replaces OEM # 23811-292-000 (Plate) and OEM # 92101-06016-0A (Bolts) X2.
Gear Change Lever
Gear Change Lever Universal Fit Spline Diameter 11.5mm Total Length 5 1/8" Offset 1 3/8"
Front Brake Caliper Adjuster Set
Front Brake Caliper Adjuster Set. Includes Adjusting Bolt, Spring, Washer and Nut.
Kickstart Oil Seal
Kickstart Oil Seal - 18 x 29 x 7 - Replaces OEM # 91204-286-003
Tach Drive Oil Seal
Tach Drive Oil Seal - 4.8 x 14.5 x 4 - Replaces OEM # 91256-096-651
Horn ~ Similar to Stock Style
Horn with Chrome Cover - 12 Volt 3 Amp - 103 Decibel - This is Not identical to the stock type but has a somewhat similar design to the stock type on these bikes.
Turn Signal Lamp Gasket
Turn Signal Lamp Gasket, Replaces OEM # 33443-268-671
Pilot Lamp Indicator Panel Dash Light Harness
Pilot Lamp Indicator Panel Dash Light Harness, Replaces OEM# 37581-323-000 / 37581-374-670 Comes complete with bulbs.
High Performance Kibblewhite Black Diamond Exhaust Valve
High Performance Kibblewhite Black Diamond Exhaust Valve. Replaces OEM# 14721-323-005. Made in the USA by Kibblewhite who have been making High Quality Performance parts for 75+ years. All Black Diamond Stainless steel valves are impregnated by a special German process to a depth of .002, with a surface build up of .0002. This Black Diamond process improves wear properties, reduces friction, and provides resistance to corrosion and wear that is superior to chrome and nickel electrolysis plating. Each valve is designed using Finite Element Analysis software, and profiles are tested on our computerized flow bench. Black Diamond Valves are lightweight, strong, one piece forgings with profiles that provide excellent flow characteristics. Sold Each, Order the Quantity you Require
Cylinder Head Gasket
Cylinder Head Gasket - OEM Ref.# 12251-374-306
Cylinder Head Cover Gasket
Cylinder Head Cover Gasket - OEM Ref.# 12391-323-000
Alternator Cover Gasket
Alternator Cover Gasket - OEM Ref. # 11691-323-306
Carburetor Screw Kit
Carburetor Screw Kit. Get a new set of screws to clean up the look of your carbs!
Positive (+) Battery Cable
Positive (+) Battery Cable with Rubber End Covers. Replaces OEM # 32401-323-000
Negative (-) Battery Cable
Negative (-) Battery Cable (Ground Cable). Replaces OEM # 32601-323-000
Rear Stock Type Rim
Chrome Rear Stock Type Rim, 1.85" Width x 18" x 40 Hole. These are high quality rims made by D.I.D who originally made the OEM rims. Replaces OEM # 42701-404-771
Exhaust Stud Set
Exhaust Stud Set. Includes 8 Exhaust Studs, 8 Washers and 8 Nuts.
Rear Wheel Bearing Retainer
Rear Wheel Bearing Retainer, Replaces OEM# 41231-323-020 This is the Rear Wheel - Left Bearing Retainer
Chrome Speedometer & Tachometer Cover Set
Set of Chrome Plated Speedometer & Tachometer Covers. These go over the stock speedo and tach gauges to give them a great chrome look! Diameter at Base of Cover - 103mm Diameter at Top of Covers - 87mm Height of Covers - 37mm Includes a small hole in one of the covers for the tripmeter. Note: Speedo/Tach Not Included, Shown in Photo to illustrate how they look when installed.
Stock Style Speedometer - KPH
Stock Style Speedometer KPH with back illumination, Face dial ranges from 0-240KPH. The ratio of this Speedometer is 100KPH=2330 RPM which is the ratio used on all stock type CB's. Note: The Speedometers slightly changed from year to year, this may not be an exact stock match for your bike but will work great! Housing Size approx 4.6", face 3.9" Check the photo for the design.
Dynatek Dyna S Ignition System
Dynatek Dyna S Ignition System. The Dyna S is a complete self-contained electronic ignition system built with the latest state-of-the-art engineering. This is the same ignition used by top racers over the past 2 decades. The Dyna S is completely housed behind the ignition cover and uses a magnetic rotor with the original spark advancer, so the factory advance curve is maintained. Increases power and reduces vibration, backfiring and intake reversion, especially on engines with radical cam timing. Front and rear cylinder timing may be set individually. Perfect for hot dual-plugged engines. The Dyna S ignition is a time proven solution to the basic ignition and trigger needs of the modern motorcycle. The Dyna S is the standard of performance and reliability. Very high quality made in the USA. This ignition can be used with your stock coils or any other coils 3 ohms or higher. Includes instructions and comes with a one year warranty through Dynatek.
Contact Point
Contact Point - Right Side OEM Ref # 30203-300-005 / 30203-300-154