Honda ► CB500K ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB500K with universal parts included that match “screws nuts bolts tools”►
- Honda
Ignition Switch Nut Tool
Ignition Switch Nut Tool, used to loosen and tighten the igntion switch nut properly without causing any damage to the switch.
Tappet Adjuster Screw & Nut Set
Tappet Adjuster Screw & Nut Set. Each Set includes one Tappet Adjuster Screw and one Nut. Replaces OEM # 90012-426-000 (Adjuster), OEM # 90206-250-000 (Nut). Note: Order the Quantity of Sets your Bike Requires
Side Stand Pivot Bolt & Nut Set
Side Stand Pivot Bolt & Nut Set, This is the Set Used to Fasten the Side Stand in Place. Replaces OEM # 90108-283-000 (Bolt) and 94002-10000-0S (Nut).
Handlebar Clutch Lever Pivot Bolt & Nut Set
Handlebar Clutch Lever Pivot Bolt & Nut Set. This is the Set that Fastens the Clutch Lever in Place. Includes One Bolt with One Nut. Replaces OEM # 90114-310-000 (Bolt) and OEM # 94001-06200-0S (Nut).
Handlebar Brake Lever Pivot Bolt & Nut Set
Brake Lever Pivot Bolt & Nut. This is the Set that Fastens the Brake Lever in Place. Includes One Bolt with One Nut. Replaces OEM # 90114-300-000
Engine Cover Bolt Set
High Quality Premium Stainless Steel Engine Cover Bolt Set Set includes: 57 Bolts, 11 Washers and 2 Allen keys for a total of 70 pieces. These bolts are all smooth head Allen bolts and are for the cylinder head cover, the left and right engine covers - points, clutch, alternator, sprocket and starter motor covers. The washers go under 8 of the cylinder head cover screws with washers from the factory, and one of the alternator cover screws, and the two starter motor cover screws.
Turn Signal Pinch Bolt Set
Turn Signal Pinch Bolt Set. Includes 2X Chrome Bolts, 2X Hex Nuts and 4X Flat Washers. This set is used to clamp the turn signal onto the stem. Some models originally had a 25mm long bolt but these will interchange. This set includes hardware for 2 turn signals. If you need enough for all 4 signals please purchase 2 sets.
Custom Drive Chain Adjuster Screws ~ Black ~ Joker Machine
Joker Machine Brand ~ Black Custom Type Drive Chain Adjuster Screws (Set of 2) with Gold Cadium Plated Nuts. Replace OEM # 90119-283-000 Features a CNC Machined Knob Section with 3 methods of Adjusting (By Hand with the Knurled Section, With an Open or Box Wrench on the Hex or with an Allen Wrench through the End of the Knob to the Screw). These Adjuster Screws Look Very Sharp and Improve the Look of your Bike. High Quality Made in the U.S.A.
Front Brake Caliper Adjuster Set
Front Brake Caliper Adjuster Set. Includes Adjusting Bolt, Spring, Washer and Nut.
Shock Absorber Nut
Shock Absorber Nut, Used when Installing Shocks. Replaces OEM # 90309-315-000 Note: Nuts sold Each, order the quantity you require
Steering Stem Nut
Chrome Steering Stem Nut, Hex Nut Size 30mm. Replaces OEM # 90304-415-000 Note: Sold Each, order the quantity your require
Carb Float Setting Tool
Carb Float Setting Tool. Use this tool to help set your floats with ease! This pre-set float setting gauge is for the models/years below only. Fits: Honda CB500K (1971-73), CB550K (1974-76), CB550F (1975-77) Supersport
Ignition Switch Assembly
Ignition Switch Assembly Square End Plug Type - 4 Prong OEM Ref # 35100-341-700 / 35100-374-007 / 35100-369-740 Note: We offer an ignition switch nut tool to easily loosen or tighten the ignition switch nut without causing damage to the switch.
Lens Screw
Tail Light Lens Screws, Pack of 10. Replaces OEM # 93500-04050-4J ISO Std. Pitch - Steel Plated Size: 4 x 50mm
Lens Screw
Tail Light Lens Screws, Pack of 10 Screws. Replaces OEM # 93500-04055-4J ISO Std. Pitch - Steel Plated Size: 4 x 55mm
Brake Rod Adjusting Nut
Brake Rod Adjusting Nut, Replaces OEM # 95015-42000
Drive Chain Adjuster Set
Complete Drive Chain Adjuster Set, Includes 2 Chain Adjusters, 2 Chain Adjusting Bolts and 2 Adjuster Nuts. Replaces OEM # 95014-19000
Carburetor Screw Kit
Carburetor Screw Kit. Get a new set of screws to clean up the look of your carbs!
Front Wheel Bearing Retainer Ring Tool
Front Wheel Bearing Retainer Ring Tool. High quality tool for removing and fitting the front wheel bearing retainer ring with 1/2 inch socket bar wrench tool hole. The perfect tool for easier removal and fitting without damaging the special retainer ring.
Black Steering Stem Nut ~ Joker Machine
Joker Machine Brand ~ Black Steering Stem Nut, Hex Nut Size 30mm. Replaces OEM # 90304-415-000 High quality CNC machined part made in the U.S.A.
Side Cover Emblem Attachment Nut
Side Cover Emblem Attachment Nut, Replaces OEM# 90315-504-000 Sold Each, Order the Quantity you Require
Throttle Adjusting Bolt
Throttle Adjusting Bolt, Replaces OEM # 53190-300-000
Float Bowl Drain Screw
Float Bowl Drain Screw w O-Ring. Note: We sell these each, order the quantity you require
Custom Black Gas/Fuel Tank Cap Latch Assembly ~ Joker Machine
Joker Machine Brand ~ Custom Black Gas/Fuel Tank Cap Latch Assembly, Includes Black Latch, Return Spring and Alloy Screw attachment with nut. A fully CNC machined, billet aluminum alternative to the discontinued cast thumb latches. Install is easily made with the provided alloy screw attachment with nut. Much more durable and stronger than the original die-cast piece. High quality CNC machined part made in the U.S.A. Ties in great with our Custom Black Gas/Fuel Tank Cap (#73-1156)
Chrome Spin On Oil Filter
Chrome Spin On Oil Filter Replaces Stock OEM Housing, Filter Bolt and Paper Element Filter. Note: When installing screw in the threaded bung first and then install the filter onto the bung.
Tongued Front Disk Rotor Washer & Nut Set
Front Disk Rotor A8 Tongued Washer & Nut Set. This Set Includes 3 Washers and 6 Nuts. Replaces OEM # 94108-18000 (Tongued Washers) and OEM # 94001-08000-0S (Nuts). These Washers are used for Locking the Nuts that Hold the Front Disc to the Hub.
Headlight Adjusting Screw & Spring Set
Headlight Adjusting Screw & Spring Set. Each Set Includes One Screw and One Spring. Replaces OEM # 33103-346-670 (Screw) and OEM # 33107-300-003 (Spring)
Air Screw Needle O-Ring
Air Screw Needle O-Ring. 2.8mm x 1.2mm. Note: sold each, order the quantity you require
Fuel Petcock Screw and Washer Set
Set of 2 Chrome Plated Fuel Petcock Screws with 2 Fibre Washers. These Screws replace OEM # 93500-06028-0A These screws fasten the fiber washers to the inside of the petcock and attach to the Fuel Tank. It is always a good idea to replace these when installing a New Fuel Petcock on your CB750K (1969-74), CB550K (1974) or CB500K (1971-73). Purchase these with our Petcock #20-8039
Front Brake Caliper Bleed Screw
Front Brake Caliper Bleed Screw. Replaces OEM # 45224-579-013
Tail Light Assembly
Tail Light Assembly. Includes Brake Light Lens, Back Plate, Screws, Gasket, Wires, Connector and Dual Filament Bulb. Replaces OEM # 33700-292-671 / 33700-235-673 / 33701-300-671 / 33701-307-670 Two Bolt Back Mounting Bolt Pattern (Approx 96mm Center to Center), 2 Wires, Ready to Mount to your Bike!
Flange Knock Bolt (Set/2)
Flange Knock Bolt (Set/2). These Bolts Fasten to the Cam Sprocket. Replaces OEM # 90082-HA0-000
Swingarm Pivot Bolt Locknut with Washer
Swingarm Pivot Bolt Locknut with Locknut Washer. Replaces OEM # 90354-268-000 (Locknut) and OEM # 90526-268-000 (Washer).
Front Brake Caliper Bolt & Washer Set
Front Brake Caliper Bolt & Washer Set. Set includes 2 Bolts and 2 Washers. Replaces OEM # 90165-323-000
Signal Lamp Lens w Gasket & Screws - Red
Red Front/Rear Turn Signal Lamp Lens with Gasket and 2 Screws. OEM Ref # 33402-268-671
Brake Caliper Bleed Screw Rubber Cap (Stock Type)
Stock Type Brake Caliper Bleed Screw Rubber Cap. These are the Same Design Rubber Caps as the Originals from the Factory. Replaces OEM # 45110-300-003 / 45224-579-013
Float Bowl Drain Screw O-Rings Pk/4
Float Bowl Drain Screw O-Rings Pk/4
Rectifier/Regulator
Rick's Electric Brand OEM Style Honda Rectifier-Regulator: This is a combination unit which will replace the OEM regulator and rectifier; stock type plugs and installation instructions are included. Dimensions 68mm Length, 94mm Width, 26mm Height, Hole Distance 80.0mm Center to Center. High quality Part. Note: May require a custom mounting job. Works great if attached with one bolt and nut where the safety starter switch was originally located (can bypass that switch).
Drain Plug Crush Washer
Drain Plug Crush Washer 12mm x 18mm x 1mm
Oil Drain Plug
Magnetic Oil Drain Plug 12mm Diameter 1.50 Thread Pitch OEM Ref # 92800-12000 / 92066-1174 / 01107-12208
Oil Passage Cap with O-Ring
Oil Passage Cap with O-Ring. Replaces OEM # 15331-300-000 (Oil Passage Cap) and OEM # 94608-40000 (O-Ring). Note: Sold Each, Order the Quantity of Caps you Require
Custom Performance Magnetic Oil Drain Plug ~ Joker Machine
Joker Machine Brand ~ Custom Performance Magnetic Oil Drain Plug - 12mm. Dia x M1.5 - OEM Ref # 92800-12000 Plug features an extended length HIGH POWER "rare earth" Neodymium-Iron-Boron Magnet pressed into the body which grabs steel debris from your tank and motor exceptionally well! High Quality CNC machined part made in the U.S.A. Works on the oil tank drain (right side of bike) and on the oil pan drain (beneath the engine) - use two for the ultimate engine oil debris collection set-up.
Exhaust Stud Set
Exhaust Stud Set. Includes 8 Exhaust Studs, 8 Washers and 8 Nuts.
Stock Type Reflector
Stock Type Screw on Reflector, 6mm thread. Replaces OEM # 33741-340-670
Front Sprocket Lock Plate Set
Front Sprocket Lock Plate with 2 Lock Plate Bolts. It's Always good to replace these when installing a new front sprocket. Replaces OEM # 23811-292-000 (Plate) and OEM # 92101-06016-0A (Bolts) X2.
Velocity Stack Set
Velocity Stack Set. These Velocity Stacks are a High Quality, 39mm ID, Taper Tipped Build. Set Comes Complete with 4 Velocity Stacks with Debris Screens, Set Screws and Set Screw Allen Wrench. These install easily and look amazing once installed!
Carburetor Stabilizer Bracket
Carburetor Stabilizer Bracket. These high quality made in Canada stainless steel brackets stabilize the carburetors when the air box is removed. A must have for pods or hard tails!
Custom Brake Rod Adjuster Knob ~ Joker Machine
Joker Machine Brand ~ Custom Brake Rod Adjuster Knob, Replaces OEM # 95015-42000 Gives your bike a great custom look while refining the quality of your brake adjuster knob! Makes for super easy brake adjustments due to the choice of a knurled outside knob and a hex nut feature all in one. High quality CNC machined part, made in the U.S.A.
Custom Black Gas/Fuel Tank Cap ~ Joker Machine
Joker Machine Brand ~ Custom Black Gas/Fuel Tank Flip Up Billet Cap. Includes Cap with a spring loaded alloy flange, replaceable rubber gasket and alloy screw attachment. Replaces OEM # 17510-323-310 Installs easily onto the tank hinges with an alloy screw (not rivets found on the stock set-up) in minutes. Lightweight design is made from a solid block of 1" thick Billet aluminum. Works with stock style latching mechanisms (Sold Separately). High quality CNC machined cap made in the U.S.A.