Honda ► CB500T ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB500T►
- Honda
Rectifier
Rectifier with female connector, Replaces OEM# 31700-455-671 / 31700-358-305 / 31700-358-013
Hot Shot Rectifier / Regulator
Rick's Electric Brand Hot Shot Rectifier / Regulator. Replaces OEM# 31400-292-670 / 31700-455-671 / 31700-292-008. This combination unit works with the stock stator to provide an upgraded charging system; it allows the stator to charge at full capacity 100% of the time! This is a direct plug-in combination rectifier-regulator that looks the same as the OE version & will mount in the same location as the OE rectifier for easy install. This unit is NOT compatible with lithium-ion batteries. If you have a Lithium Ion battery installed we sell a lithium ion version of this item.
Condenser
Condenser - Replaces OEM# 30250-369-004 / 30280-292-672 / 30280-292-671 / 30280-371-000
Fork Seals
Fork Seals Set/2 35 X 48 X 10.5/11
Fork Dust Boots
Fork Dust Boots Set/2 OEM Ref # 51425-375-003 / 51425-375-005
Wheel Seal Kit
Front Wheel Seal Kit 1 Seal
Wheel Seal Kit
Rear Wheel Seal Kit 1 Seal 34 x 55 x 9
Swing Arm Bushing Set
Swing Arm Bushing Set OEM Ref # 52108-457-300 Note: These Replace the factory plastic OEM Type Bushings.
High Performance Kibblewhite Bronze Swingarm Bushing Set
High Performance Kibblewhite Bronze Swingarm Bushing Set/2. Replaces OEM# 52108-457-300, 52108-422-300. Made in the USA by Kibblewhite who have been making High Quality Performance parts for 75+ years. Kibblewhite bronze bushings offers increased durability and better fitment then the OEM type bushings.
Rear Wheel Bearing Retainer
Rear Wheel Bearing Retainer - Sprocket Side - Replaces OEM# 41231-283-000 This retainer is used on the (sprocket side) of the bike.
Front Wheel Bearing Retainer
Front Wheel Bearing Retainer - Replaces OEM# 44643-300-000
Rear Wheel Bearing
Rear Wheel Bearing with 2 Synthetic Shields - 6305-2RS Size Replaces OEM# 96140-63050-10 High Quality Made in Japan
Rear Shock Swingarm Bushing
Rear Shock Swingarm Bushing, Replaces OEM# 40548-268-000 19mm Long, 22mm OD, 10mm ID. Sold Each, Order the Quantity you Require
Master Cylinder Reservoir Cap
Master Cylinder Cap with Plastic O-Ring. Replaces OEM # 45513-341-771 This style of master cylinder cap was discontinued long ago by Honda. We have had these produced again to keep your bike looking sharp. Spruce up your Master Cylinder with one of these great looking master cylinder caps!
Front Brake Caliper Piston
Front Brake Caliper Piston (1) - 38.15mm Diameter x 34mm Height - Replaces OEM # 45107-323-020. Please note: the side with the 2mm outer lip faces the brake pad during install.
Master Cylinder Reservoir Cap Plastic O-Ring
Master Cylinder Reservoir Cap Plastic O-Ring, Replaces OEM # 45521-MJ6-006
Reservoir Cap & Diaphragm
Reservoir Cap & Diaphragm Round Thread On Type OEM Ref # 43515-MJ6-006 / 45520-300-000
Front Brake Caliper Piston Sealing Ring
Front Brake Caliper Piston Sealing Ring, Replaces OEM # 45108-300-003
Speedo Gear Plug
Speedo Gear Plug - Plug 15mm Outer Diameter, 22mm Long. This Plug is Great for Keeping your Original Speedo Drive Gear Clean.
Rear Brake Shoes
Rear Brake Shoes Pk/2 Diameter: 178.5mm Width: 30mm OEM Ref # 43120-283-670
Front Brake Pads
Front Brake Pads Pk/2 OEM Ref # 45105-390-006A
Brake Rod Spring
Brake Rod Spring. Replaces OEM # 95014-73100
Headlight Adjusting Screw & Spring Set
Headlight Adjusting Screw & Spring Set. Each Set Includes One Screw and One Spring. Replaces OEM # 33103-346-670 (Screw) and OEM # 33107-300-003 (Spring)
Brake Caliper Bleed Screw Rubber Cap (Stock Type)
Stock Type Brake Caliper Bleed Screw Rubber Cap. These are the Same Design Rubber Caps as the Originals from the Factory. Replaces OEM # 45110-300-003 / 45224-579-013
Hydraulic Brake Light Switch
Hydraulic Brake Light Switch - OEM Ref # 35350-300-006 / 35350-300-016 / 341-83980-30-00 10mm x M1.25 thread
Special Oil Filter Rotor Washer
Special Angled Oil Filter Rotor Washer (16mm), Replaces OEM# 90481-292-000
Master Cylinder Rubber Boot
Master Cylinder Rubber Boot. This Boot Attaches to where the Brake Hose Joins to the Master Cylinder. Replaces OEM # 45522-300-010
Clutch Plate
Clutch Plate 7 Piece Required OEM Ref # 22201-283-000 / 22201-MA7-000
Steel Clutch Plate
Steel Clutch Plate 6 Pieces Required
Carb Rebuild Kit
Carb Rebuild Kit. Note: Each Kit Rebuilds One Carb, Order the Quantity of Kits you Require
Float Needle & Seat
Float Needle & Seat High Quality - Made In Japan OEM Ref # 16011-302-004 / 16011-375-004
Float Bowl Drain Screw
Float Bowl Drain Screw w O-Ring. Note: We sell these each, order the quantity you require
Carburetor Screw Kit
Carburetor Screw Kit. Get a new set of screws to clean up the look of your carbs!
Shock Absorber Nut
Shock Absorber Nut, Used when Installing Shocks. Replaces OEM # 90309-315-000 Note: Nuts sold Each, order the quantity you require
Front Sprocket Lock Plate Set
Front Sprocket Lock Plate with 2 Lock Plate Bolts. It's Always good to replace these when installing a new front sprocket. Replaces OEM # 23811-292-000 (Plate) and OEM # 92101-06016-0A (Bolts) X2.
Steering Stem Nut
Chrome Steering Stem Nut, Hex Nut Size 30mm. Replaces OEM # 90304-415-000 Note: Sold Each, order the quantity your require
Steering Stem Washer
Chrome Steering Stem Washer, Replaces OEM # 90503-283-000 Sold Each, order the quantity you require.
Side Stand Spring
Side Stand Spring, Replaces OEM # 95014-72402
Fork Cap O-Ring Set/2
Fork Cap O-Ring Set of 2. 23mm x 2.8mm size. Replaces OEM # 94608-50000 X2.
Speedometer Cable
Speedometer Cable - Black - OEM Ref. # 44830-425-870 End to End Length 38.5" Made in Japan
Front Brake Hose "A"
Front Brake Hose "A", Attaches 3-Way Joint to Front Brake Pipe. Replaces OEM # 45125-300-003
Front Brake Hose "B"
Front Brake Hose "B", Connects Front Brake Master Cylinder to 3-Way Joint. Replaces OEM # 45126-300-003
Cam Chain
Cam Chain 219T x 128 D.I.D (Daido) Takes 01-8803 Rivet Link Pitch: .3061" Side Plate: Peanut Average Tensile Strength: 1800lbs OEM Ref # 14401-283-003 / 94500-02128
Cam Chain 219FTSS x 128
Cam Chain 219FTSS x 128 D.I.D (Daido) Takes 01-8802 Rivet Link Pitch: .3061" Side Plate: Steeped Parallel Plate Average Tensile Strength: 1896lbs OEM Ref # 14401-283-003 / 94500-02128
Brake Hose Rubber Grommet
Brake Hose Rubber Grommet, This is the Rubber Grommet that Attaches to the Brake Hose. Replaces OEM # 45146-300-000
Starter Motor Terminal Rubber Boot
Starter Motor Terminal (Cover) Rubber Boot. Replaces OEM # 32411-230-000
Shock Absorber Joint Rubber Set/2
Shock Absorber Joint Rubber Set/2. Replaces OEM # 52484-292-000
Speedo/Tachometer Meter Cushion
Speedo/Tachometer Meter Cushion, Replaces OEM # 37235-323-700
Headlight Plug ~ OEM Style
Headlight Plug ~ OEM Style, Replaces OEM # 33130-300-003
Seat Lock with Keys
Seat Lock with Keys, Replaces OEM # 77230-399-007 / 77230-107-711 This seat lock works perfect for the bikes listed but the locking mechanism sticks out a bit farther then the OEM type. If you have lost your old key you have to remove the seat lock bracket and assembly. This can be done with a short 10mm wrench or socket, once that's done the rest is easy.