Honda ► CB550F ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB550F with universal parts included►
- Honda
Seat Hinge Pin
Seat Hinge Pin, Replaces OEM # 77103-313-000 Note: 2 Used Per Bike, Order the Quantity you Require
Crank Seal
Crank Seal - 30 x 42 x 8 - Replaces OEM # 91201-300-003 Note: Please Reference the OEM Number and Seal size above to make sure this is the Crank Seal you Require. Some models use 2 Different Crank Seals.
Kickstart Oil Seal
Kickstart Oil Seal - 18 x 29 x 7 - Replaces OEM # 91204-286-003
Tach Drive Oil Seal
Tach Drive Oil Seal - 4.8 x 14.5 x 4 - Replaces OEM # 91256-096-651
Intake Valve
Intake Valve - Replaces OEM # 14711-107-020 Made in Japan
Exhaust Valve
Exhaust Valve - Replaces OEM # 14721-323-005 / 14721-324-010 / 14721-324-000 / 14721-107-020 Made in Japan
Front Brake Caliper Bleed Screw
Front Brake Caliper Bleed Screw. Replaces OEM # 45224-579-013
Handlebar Clutch Lever Pivot Bolt & Nut Set
Handlebar Clutch Lever Pivot Bolt & Nut Set. This is the Set that Fastens the Clutch Lever in Place. Includes One Bolt with One Nut. Replaces OEM # 90114-310-000 (Bolt) and OEM # 94001-06200-0S (Nut).
Front Fender Hardware/ Fender Stay Hardware Set
3 PC. Front Fender Hardware/ Fender Stay Hardware Set. Includes Setting Rubber, Bolt and Metal Collar. Replaces OEM#40513-310-000 (Rubber), OEM#40514-310-000 (Metal Collar) and OEM#92101-06020-0A (Bolt). Purchase the Quantity of Sets you Require for your Application
Premium ~ Piston Ring Set (Standard Size)
Premium Japanese made Superior Quality ~ Standard Size Piston Ring Set Ring Set OEM Ref # 13011-374-000 (Std.) Note: This Set includes piston rings to rebuild one piston, 4 Sets are needed to rebuild all pistons.
Front Brake Caliper Bolt & Washer Set
Front Brake Caliper Bolt & Washer Set. Set includes 2 Bolts and 2 Washers. Replaces OEM # 90165-323-000
Swingarm Dust Seal Cap (Set/2)
Swingarm Dust Seal Cap (Set/2). These Caps go on the Ends of the Swingarm Pivot. Replaces OEM # 52144-362-000 X2.
Handlebar Brake Lever Pivot Bolt & Nut Set
Brake Lever Pivot Bolt & Nut. This is the Set that Fastens the Brake Lever in Place. Includes One Bolt with One Nut. Replaces OEM # 90114-300-000
Side Stand Rubber Hardware Set
Side Stand Rubber Hardware Set, Includes Metal Collar, Bolt and Washer.
Turn Signal Lamp Lens Screw Set
Turn Signal Lamp Lens Screw Set/2, Replaces OEM # 93500-04025-0A ALSO Fits our Signal Lens #11-2195 and Signals #11-2114 and #11-2149
Carb Bolt Kit
Carburetor Bolt and Washer 36 Piece Kit. This is a Complete Bolt Kit for All 4 Carburetors.
Custom Drive Chain Adjuster Screws ~ Black ~ Joker Machine
Joker Machine Brand ~ Black Custom Type Drive Chain Adjuster Screws (Set of 2) with Gold Cadium Plated Nuts. Replace OEM # 90119-283-000 Features a CNC Machined Knob Section with 3 methods of Adjusting (By Hand with the Knurled Section, With an Open or Box Wrench on the Hex or with an Allen Wrench through the End of the Knob to the Screw). These Adjuster Screws Look Very Sharp and Improve the Look of your Bike. High Quality Made in the U.S.A.
Custom Type Black Fork Caps (Set/2) ~ Joker Machine
Joker Machine Brand ~ Custom Black Fork Cap Set of 2 with O-Rings. Replaces OEM # 90123-300-000 High quality CNC machined from billet aluminum, much lighter then the stock type. Gives your bike a great custom look. Made in the U.S.A.
Seat Lock Bar Assembly
Seat Lock Bar Assembly, Replaces OEM# 77220-340-003 / 77220-340-011
Custom Brake Rod Adjuster Knob ~ Joker Machine
Joker Machine Brand ~ Custom Brake Rod Adjuster Knob, Replaces OEM # 95015-42000 Gives your bike a great custom look while refining the quality of your brake adjuster knob! Makes for super easy brake adjustments due to the choice of a knurled outside knob and a hex nut feature all in one. High quality CNC machined part, made in the U.S.A.
Custom Rear Brake Stopper Arm Strap ~ Joker Machine
Joker Machine Brand ~ Custom Rear Brake Stopper Arm Strap, Replaces OEM # 43431-286-010 / 43431-340-000 This strap is lightweight, identical length to the stock strap and really gives your bike a great custom look! High quality part CNC machined in the U.S.A.
Custom Performance Magnetic Oil Drain Plug ~ Joker Machine
Joker Machine Brand ~ Custom Performance Magnetic Oil Drain Plug - 12mm. Dia x M1.5 - OEM Ref # 92800-12000 Plug features an extended length HIGH POWER "rare earth" Neodymium-Iron-Boron Magnet pressed into the body which grabs steel debris from your tank and motor exceptionally well! High Quality CNC machined part made in the U.S.A. Works on the oil tank drain (right side of bike) and on the oil pan drain (beneath the engine) - use two for the ultimate engine oil debris collection set-up.
Tach Drive Plug Block Off ~ Black ~ Joker Machine
Joker Machine Brand ~ Black Tach Drive Plug (Block Off). This plug is generally used when the tachometer cable drive is removed and still needs to be blocked off to prevent oil leakage. This plug has an o-ring groove machined in it for better sealing. Several bike builders just cut the stock cable off and left the Honda cable drive end installed in the valve cover. This plug is a much cleaner option in both functionality and looks. These plugs are a real nice touch when you are not using the stock tachometer, and need to eliminate the cable, or are using an electronic tach. Installs in about a minute, no need to remove the valve cover to remove the tach drive gear assy. High quality CNC machined part, made in the U.S.A.
Front Stock Type Rim
Chrome Front Stock Type Rim, 1.85" Width x 19" x 40 Hole, Overall Actual Width 2.75". These are high quality rims made by D.I.D who originally made the OEM rims. Replaces OEM # 44701-405-771
Rear Stock Type Rim
Chrome Rear Stock Type Rim, 1.85" Width x 18" x 40 Hole. These are high quality rims made by D.I.D who originally made the OEM rims. Replaces OEM # 42701-404-771
Seat Cover
Replacement Seat Cover with Reinforced Passenger Strap (No hardware or chrome trim included just re-use existing hardware). There is not a "Honda" stencil on the rear of the cover due to copyright. There is a layer of foam sewn into the top of the seat cover to improve ride comfort and smooth out any defects in your seat foam. Each seat cover is made entirely by hand, it is crafted slowly with great care by a gifted master upholster, using only the top grade materials available. Comes with complete installation instructions as well as step by step instructions on how to repair damaged seat foam. Fits: the Original Stock Honda CB550F (1975-77) Supersport Seat Only This is for the SEAT COVER, Not the Full Seat, Photo Shows Seat Cover Installed for reference
Handlebar - Stock Type ~ CB550F 1975-76
Stock Type Handlebar for the CB550F (1975-76) - Chrome. The holes are pre-cut for routing the wiring from the switches to the harness. There are also holes drilled to fit the pins in the stock switches to keep them from rotating. Bar Diameter - 7/8" - 22mm, Length - 28 1/4" - 718mm, Pull Back - 3 3/4" - 95mm, Inner Rise - 3 3/8" - 86mm, End Rise - 4 1/2" - 114mm, Center Width - 5 1/4" - 133mm, Base Width - 7 1/2" - 190mm, Knurl Width - 4 1/2" - 114mm, Control Length - 8" - 203mm, Drilled - YES Replaces OEM # 53100-390-620 Note: These Are Drilled For Wires
Handlebar Clamp Set /2
Black Handlebar Clamp Set/2. These clamp the stock 7/8" handlebars to the upper triple clamp. Replaces OEM # 95014-22200
Exhaust Stud Set
Exhaust Stud Set. Includes 8 Exhaust Studs, 8 Washers and 8 Nuts.
Velocity Stack Set
Velocity Stack Set. These Velocity Stacks are a High Quality, 39mm ID, Taper Tipped Build. Set Comes Complete with 4 Velocity Stacks with Debris Screens, Set Screws and Set Screw Allen Wrench. These install easily and look amazing once installed!
Rectifier/Regulator
Rectifier-Regulator: This is a combination unit which will replace the OEM regulator and rectifier. This has the OEM type ground wiring and Stock Type Plugs. Dimensions 80mm Length, 94mm Width, 27mm Height, Hole Distance 70.0mm Center to Center. Instructions not included.
Electronic Ignition System
Electronic Ignition System. Direct plug-in fitment. Increase RPM 100% tested before shipment, high reliability and high performance! This ignition can be used with your stock coils or any other coils 3 ohms or higher.
Pilot Indicator Light Cover
Pilot Indicator Light Cover, Replaces OEM# 37600-377-018 This includes the front and rear cover with fastening screws.
Drive Chain Adjuster
Drive Chain Adjuster with Nut and Bolt, Replaces OEM# 95014-18000 / 40543-390-000 / 40532-283-010. If you require 2 adjusters purchase 2 of this part.
Rear Wheel Bearing Retainer
Rear Wheel Bearing Retainer, Replaces OEM# 41231-323-020 This is the Rear Wheel - Left Bearing Retainer
Piston Ring Set (Standard Size)
Standard Size Piston Ring Set Replaces OEM# 13011-374-000 Fits: Honda CB550K (1974-78), CB550F (1975-77) Supersport Note: This Set includes piston rings to rebuild one piston, 4 Sets are needed to rebuild all pistons.
Piston Kit (Standard Size)
Standard Size (58.5mm) Piston with Piston Rings, Piston Pin and Piston Pin Clips (pr.) Replaces OEM# 13101-374-000 (standard piston), 13011-374-000 (Rings), 94601-15000 (Clip), 13111-286-000 (Pin) Fits: Honda CB550K (1974-78), CB550F (1975-77) Supersport Note:This Kit includes piston,piston rings, piston pin and clips to rebuild one piston. 4 Kits are needed to rebuild all pistons.
Stock Type Battery Band
Stock Type Battery Band, Replaces OEM# 95012-17001 Band Overall Size: 6.125" (155mm) Measuring from the inside of the brackets.
Headlight Reflector Rubber Base
Headlight Reflector Rubber Base, Replaces OEM# 33743-375-000 This is the rubber base that the headlight reflector attaches to. Sold Each, order the quantity you require
Headlight Stay / Headlight Reflector Bolt
Headlight Stay / Headlight Reflector Bolt, Replaces OEM# 90120-377-000 This is the bolt that the headlight reflectors / reflector base attach to, this bolt fastens to the headlight. Sold Each, 2 Used Per Bike
Battery Box Rubber
Battery Box Rubber, Replaces OEM# 83618-323-000 Sold Each, Order the Quantity you Require
Horn ~ Similar to Stock Style
Horn with Chrome Cover - 12 Volt 3 Amp - 103 Decibel - This is Not identical to the stock type but has a somewhat similar design to the stock type on these bikes.
Alternator Cover ~ Honda Brand OEM
Honda Brand OEM ~ Alternator Cover. This is a genuine Honda made Alternator Cover, Replaces OEM# 11632-323-003.
Cam Chain Tensioner - Honda OEM # 14500-323-000/010 CB500/550
CB500/550 Cam Chain Tensioner Honda OEM # 14500-323-000/010
Handmade Christmas Stocking
HAPPY HOLIDAYS! We are thrilled to be able to offer handmade, one-of-a-kind upcycled Christmas stockings by “Rider Ragsâ€. Featuring a CB750 on the front. They include belt, chain and Honda keychain. Each stocking is individually handmade so there will be variations in denim and belts. Some toes face right and some left. If you have a preference for right/left toe facing make a note in the order comments.
Universal Glas-Pak Insert
Universal Glas-Pak Insert - Fits 1 1/2" Pipes - Glass Pak's Actual Size 1 3/8" Tone down your TT or Drag Pipes
Tire Valve Stem
Tire Valve Stem - Straight Metal Type
Tire Valve Stem
Tire Valve Stem - Straight Rubber Type
Tire Valve Stem
Tire Valve Stem - 90 Degree Metal Type