Honda ► CB550F ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB550F with universal parts included►
- Honda
Speedo Gear Plug
Speedo Gear Plug - Plug 15mm Outer Diameter, 22mm Long. This Plug is Great for Keeping your Original Speedo Drive Gear Clean.
Rear Brake Shoes
Rear Brake Shoes Pk/2 Diameter: 178.5mm Width: 30mm OEM Ref # 43120-283-670
Tachometer Cable Clamp
Chrome Tachometer Cable Clamp (Holder). Replace that Old Rusted, Worn Out Clamp with a Brand New Great Looking Chrome Tach Cable Clamp. Replaces OEM # 50462-323-010
Headlight Adjusting Screw & Spring Set
Headlight Adjusting Screw & Spring Set. Each Set Includes One Screw and One Spring. Replaces OEM # 33103-346-670 (Screw) and OEM # 33107-300-003 (Spring)
Kick Starter Stopper Spring with Steel Ball
Kick Starter Stopper Spring with Steel Ball Set. Replaces OEM # 28333-300-000 (Spring) and OEM # 96211-08000 (Steel Ball).
Front Brake Caliper Adjuster Set
Front Brake Caliper Adjuster Set. Includes Adjusting Bolt, Spring, Washer and Nut.
Brake Caliper Bleed Screw Rubber Cap (Stock Type)
Stock Type Brake Caliper Bleed Screw Rubber Cap. These are the Same Design Rubber Caps as the Originals from the Factory. Replaces OEM # 45110-300-003 / 45224-579-013
Flange Knock Bolt (Set/2)
Flange Knock Bolt (Set/2). These Bolts Fasten to the Cam Sprocket. Replaces OEM # 90082-HA0-000
Hydraulic Brake Light Switch
Hydraulic Brake Light Switch - OEM Ref # 35350-300-006 / 35350-300-016 / 341-83980-30-00 10mm x M1.25 thread
Swingarm Pivot Bolt Locknut with Washer
Swingarm Pivot Bolt Locknut with Locknut Washer. Replaces OEM # 90354-268-000 (Locknut) and OEM # 90526-268-000 (Washer).
Master Cylinder Rubber Boot
Master Cylinder Rubber Boot. This Boot Attaches to where the Brake Hose Joins to the Master Cylinder. Replaces OEM # 45522-300-010
Center Stand Spring
Center Stand Spring. Replaces OEM # 95014-71702
Progressive Type Front Fork Springs
Progressive Type Front Fork Spring Set/2. Includes 10" Pipe and Washers. These Progressive Type Springs improve handling and overall ride quality. They Stop front end droop and diving during braking while improving cornering stability. A Great Performance upgrade for your Bike! Some Bikes Require that the Spacer Length be Calculated using the instructions below then the Included Pipe Cut to make the Appropriate Sized Spacers, Some Models Do Not Require Spacers. Be Sure to Check the End of the Installation Instructions Below to see if your Bike Require Spacers.
Clutch Plate
Clutch Plate 6 Pieces Required .106" Thickness OEM Ref # 22201-286-010 / 22201-415-000 / 22201-ME2-000
Clutch Plate
Clutch Plate 1 Piece Required .138" Thickness OEM Ref # 22202-371-000 / 22202-390-000 / 22202-392-000
Steel Clutch Plate
Steel Clutch Plate OEM Ref # 22321-MT3-000 Order the Quantity you require
Carb Fuel Line O-Ring Kit
Carb Fuel Line O-Ring 12Pc Kit Includes: 8 Carb Fuel Connector Tube O-Rings and 4 Float Bowl Drain Seal Connector Tube O-Rings (The 4 tubes that connect the 4 carbs together).
Float Bowl Drain Screw O-Rings Pk/4
Float Bowl Drain Screw O-Rings Pk/4
Float Bowl Drain Screw O-Rings Pk/4
Float Bowl Drain Screw O-Rings Pk/4
Clutch Adjuster O-Ring Pk/2
Clutch Adjuster O-Rings Pk/2, Replaces OEM# 91301-704-000
Carb Holder Set
Carb Holder Set (Set of 4) - Replace those old cracked or dried up carb holders with a brand new set! Replaces OEM# 16211-323-000 If you require band clamps, these carb holders require our 41-44mm diameter clamps part #15-0684 X8.