Honda ► CB650 ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB650►
- Honda
Front Wheel Bearing Retainer Ring Tool
Front Wheel Bearing Retainer Ring Tool. High quality tool for removing and fitting the front wheel bearing retainer ring with 1/2 inch socket bar wrench tool hole. The perfect tool for easier removal and fitting without damaging the special retainer ring.
Rear Wheel Bearing Retainer Ring Tool
Rear Wheel Bearing Retainer Ring Tool. High quality tool for removing and fitting the rear wheel sprocket hub bearing retainer ring with 1/2 inch socket bar wrench tool hole. OR removing and fitting the rear wheel sprocket carrier bearing retainer ring. The perfect tool for easier removal and fitting without damaging the special retainer ring. Removes Rear Wheel Sprocket Carrier Bearing Retainer Ring on the Honda CB750K (1969-78), CB750F (1975-78) Supersport, CB750A (1976-78) Hondamatic Removes Rear Wheel Hub Bearing Retainer Ring on the Honda CB750K (1969-82), CB750A (1976-78) Hondamatic CB750C (1980-82) Custom, CB750L (1979) Limited CB650 (1979-82), CB650C (1980-81) Custom, CB650SC (1982) Nighthawk
Tachometer Cable
Tachometer Cable - OEM Ref # 37260-426-000 Made in Japan
Speedometer Cable
Speedometer Cable - OEM Ref # 44830-KC1-010 Made in Japan
Choke Cable
Choke Cable - OEM # 17950-426-000 Made in Japan
Starter Solenoid Relay
Starter Solenoid Relay with Fuse. Replaces OEM # 35850-MB0-007
Oil Pressure Switch
Oil Pressure Switch, Replaces OEM # 37240-P13-013
Carb Fuel Connector Tube and Accellerator Tube O-Rings
Carburetor Fuel Connector Tube and Accellerator Tube O-Rings, 12 O-Rings.
Front Brake Caliper Shaft Boots Pk/4
Front Brake Caliper Shaft Boots Pk/4, These are the Rubber Covers that Attach to the Front Brake Caliper. Replaces OEM # 45133-413-003
Stock Type Gearshift Lever Rubber
Stock Type Gearshift Lever Rubber, Replaces OEM # 24781-419-000
Brake Rod Joint
Brake Rod/Arm Joint, Replaces OEM # 95015-32001
Brake Rod Joint Pin w Cotter Pin
Brake Rod Joint Pin with Cotter Pin, Replaces OEM # 95015-52000 (Joint Pin) and OEM # 94201-16250 (Cotter Pin).
Brake Rod Adjusting Nut
Brake Rod Adjusting Nut, Replaces OEM # 95015-42000
Valve Stem Seal
Valve Stem Seal. Replaces OEM # 12209-333-005 / 12209-333-005 Sold Each - Order the Quantity you Require
Tach Drive Plug Block Off w O-Ring
Tach Drive Plug (Block Off) with O-ring. This plug is generally used when the tachometer cable drive is removed and still needs to be blocked off to prevent oil leakage. This plug has an o-ring groove machined in it for better sealing. Several bike builders just cut the stock cable off and left the Honda cable drive end installed in the valve cover. This plug is a much cleaner option in both functionality and looks. These plugs are a real nice touch when you are not using the stock tachometer, and need to eliminate the cable, or are using an electronic tach. Installs in about a minute, no need to remove the valve cover to remove the tach drive gear assy. Fits tachometer cables that are approximately 15mm in diameter with a 10.5mm groove and held in place with a screw.
Center Stand Spring Plate
Center Stand Spring Plate, This is the Plate the Center Stand Spring Attaches to. Replaces OEM # 50523-425-000
Rear Brake Shoe Spring Set/2
Rear Brake Shoe Spring Set of 2. Replaces OEM # 43151-346-000
Fuse Box Plate Cover Screw Set
Black Fuse Box Plate Cover Screw (Set of 2). Replaces OEM # 93700-05020-0G
Footrest Rubbers
Footrest Rubbers (Set/2) - OEM Ref # 50661-425-670
Wire Harness
Main Wire Harness Loom - OEM Ref # 32100-460-000 NOTE: These fit model years and type listed, other years and bikes use a different OEM part number (there is a difference!).
Brake Disc Retaining Nut Pk/10
Brake Disc Retaining Nut Pk/10, Replaces OEM # 90309-357-000
Brake Cam Dust Seal
Brake Cam Dust Seal, Replaces OEM # 43134-300-000
Fork Seal Stopper Metal Ring Pk/2
Fork Seal Stopper Metal Ring Pk/2, Replaces OEM # 51447-KL4-951 This is the Metal Ring above the Fork Seal.
Carb Top Gasket
Carburetor Top Gasket, Replaces OEM # 16014-393-004
Carb Rebuild Kit
Carb Rebuild Kit. Contains: Float Bowl Gasket, Carb Top Gasket, Float Needle, Slide Needle and Needle Jet, Main Jet #95, Air Screw with Spring and Misc. Packing Shown.
Crank Seal
Crank Seal - 30 x 42 x 8 - Replaces OEM # 91201-300-003 Note: Please Reference the OEM Number and Seal size above to make sure this is the Crank Seal you Require. Some models use 2 Different Crank Seals.
Tach Drive Oil Seal
Tach Drive Oil Seal - 4.8 x 14.5 x 5 - Replaces OEM # 91256-425-003
Shift Shaft Oil Seal
Shift Shaft Oil Seal - 12.5 x 25 x 8 - Replaces OEM # 91204-425-003
Intake Valve
Intake Valve - Replaces OEM # 14711-426-003 Made in Japan
Exhaust Valve
Exhaust Valve - Replaces OEM # 14721-426-003 Made in Japan
Front Brake Caliper Bleed Screw
Front Brake Caliper Bleed Screw. Replaces OEM # 45224-413-003 Sold Each, Order the Quantity you Require
Handlebar Clutch Lever Pivot Bolt & Nut Set
Handlebar Clutch Lever Pivot Bolt & Nut Set. This is the Set that Fastens the Clutch Lever in Place. Includes One Bolt with One Nut. Replaces OEM # 90113-422-000 (Bolt) and OEM # 94002-06000-0S (Nut).
Press In Type Pilot Jet Set ~ Size #35 (Pk/4)
Press In Type Pilot Jet Set of 4 (Size #35) Pilot Jets (your idle and low speed operation) are critical for smooth idling and lower rpm driving. When rebuilding carbs it is highly recommended to replace these pilot jets to ensure your bike is running as well as possible. Also, when installing new exhaust or high flow air filters it is recommended to increase the size of your Pilot Jets. These are size #35 which is the stock size for these bikes, please confirm this is the size you require before purchasing. If you require oversize pilot jets we carry those as well.
Press In Type Pilot Jet Set ~ Size #38 (Pk/4)
Press In Type Pilot Jet Set of 4 (Size #38) Pilot Jets (your idle and low speed operation) are critical for smooth idling and lower rpm driving. When rebuilding carbs it is highly recommended to replace these pilot jets to ensure your bike is running as well as possible. Also, when installing new exhaust or high flow air filters it is recommended to increase the size of your Pilot Jets. These are size #38 which is oversize for these bikes, please confirm this is the size you require before purchasing.
Press In Type Pilot Jet Set ~ Size #42 (Pk/4)
Press In Type Pilot Jet Set of 4 (Size #42) Pilot Jets (your idle and low speed operation) are critical for smooth idling and lower rpm driving. When rebuilding carbs it is highly recommended to replace these pilot jets to ensure your bike is running as well as possible. Also, when installing new exhaust or high flow air filters it is recommended to increase the size of your Pilot Jets. These are size #42 which is the oversize for these bikes, please confirm this is the size you require before purchasing.
Pilot Jet Set ~ Size #35 (Pk/4)
Pilot Jet Set of 4 (Size #35), Replaces OEM # 99103-GY6-0350 Pilot Jets (your idle and low speed operation) are critical for smooth idling and lower rpm driving. When rebuilding carbs it is highly recommended to replace these pilot jets to ensure your bike is running as well as possible.
Piston Ring Set (Standard Size)
Standard Size Piston Ring Set Ring Set OEM Ref # 13011-426-004 (Std.) Japanese made Superior Quality Note: This Set includes piston rings to rebuild one piston, 4 Sets are needed to rebuild all pistons.
Swingarm Dust Seal Cap (Set/2)
Swingarm Dust Seal Cap (Set/2). These Caps go on the Ends of the Swingarm Pivot. Replaces OEM # 52144-362-000 X2.
Handlebar Brake Lever Pivot Bolt Set
Handlebar Brake Lever Pivot Bolt, Washer & Nut Set. This is the Set that Fastens the Brake Lever in Place. Includes One Bolt with One Washer and Nut. Replaces OEM # 90114-422-000 (Bolt).
Handlebar Brake Lever Pivot Bolt & Nut Set
Handlebar Brake Lever Pivot Bolt & Nut Set. This is the Set that Fastens the Brake Lever in Place. Includes One Bolt with One Nut. Replaces OEM # 90114-MA5-671 (Bolt) and OEM # 94050-06000 (Nut)
Turn Signal Lamp Lens Screw Set
Turn Signal Lamp Lens Screw Set/2, Replaces OEM # 93500-04025-0A ALSO Fits our Signal Lens #11-2195 and Signals #11-2114 and #11-2149
Front Brake Caliper Piston Boot
Front Brake Caliper Piston Rubber Dust Boot, Replaces OEM # 45109-425-003
Rear Wheel Damper Rubber
Rear Wheel Drive Damper Rubber, Replaces OEM # 41241-300-050 These fit between the rear wheel sprocket hub and the wheel hub and get worn down over time from use. Note: 4 Used Per Bike, Order The Quantity you Require
Seat Lock Bar Assembly
Seat Lock Bar Assembly, Replaces OEM# 77220-340-003 / 77220-340-011
Custom Brake Rod Adjuster Knob ~ Joker Machine
Joker Machine Brand ~ Custom Brake Rod Adjuster Knob, Replaces OEM # 95015-42000 Gives your bike a great custom look while refining the quality of your brake adjuster knob! Makes for super easy brake adjustments due to the choice of a knurled outside knob and a hex nut feature all in one. High quality CNC machined part, made in the U.S.A.
Custom Performance Magnetic Oil Drain Plug ~ Joker Machine
Joker Machine Brand ~ Custom Performance Magnetic Oil Drain Plug - 12mm. Dia x M1.5 - OEM Ref # 92800-12000 Plug features an extended length HIGH POWER "rare earth" Neodymium-Iron-Boron Magnet pressed into the body which grabs steel debris from your tank and motor exceptionally well! High Quality CNC machined part made in the U.S.A. Works on the oil tank drain (right side of bike) and on the oil pan drain (beneath the engine) - use two for the ultimate engine oil debris collection set-up.
Tach Drive Plug Block Off ~ Black ~ Joker Machine
Joker Machine Brand ~ Black Tach Drive Plug (Block Off). This plug is generally used when the tachometer cable drive is removed and still needs to be blocked off to prevent oil leakage. This plug has an o-ring groove machined in it for better sealing. Several bike builders just cut the stock cable off and left the Honda cable drive end installed in the valve cover. This plug is a much cleaner option in both functionality and looks. These plugs are a real nice touch when you are not using the stock tachometer, and need to eliminate the cable, or are using an electronic tach. Installs in about a minute, no need to remove the valve cover to remove the tach drive gear assy. High quality CNC machined part, made in the U.S.A.
Front Stock Type Rim
Chrome Front Stock Type Rim, 1.85" Width x 19" x 40 Hole, Overall Actual Width 2.75". These are high quality rims made by D.I.D who originally made the OEM rims. Replaces OEM # 44701-405-771
Seat Cover
Replacement Seat Cover with Reinforced Passenger Strap (No hardware or chrome trim included just re-use existing hardware). There is not a "Honda" stencil on the rear of the cover due to copyright. There is a layer of foam sewn into the top of the seat cover to improve ride comfort and smooth out any defects in your seat foam. Each seat cover is made entirely by hand, it is crafted slowly with great care by a gifted master upholster, using only the top grade materials available. Comes with complete installation instructions as well as step by step instructions on how to repair damaged seat foam. Fits: the Original Stock Honda CB650 (1979) Seat Only This is for the SEAT COVER, Not the Full Seat, Photo Shows Seat Cover Installed for reference
Turn Signal Relay
Turn Signal (Flasher) Relay. OEM Style Replacement 12V/23W, 3 Prong, Comes with Rubber Mount Attached. Replaces OEM # 38301-415-671 Not for Use with Custom LED Lights