Honda ► CB650C ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB650C with universal parts included►
- Honda
Throttle Cable - Push
Throttle Cable "B" - "Push Type" - OEM Ref # 17920-425-700
Clutch Cable
Clutch Cable - OEM Ref # 22870-460-700
OEM Type Gas/Fuel Tank Cap
OEM Type Gas/Fuel Tank Cap with Gasket and 2 Keys. Replaces OEM # 17620-460-067
Starter Motor Terminal Rubber Boot
Starter Motor Terminal (Cover) Rubber Boot. Replaces OEM # 32411-230-000
Shock Absorber Joint Rubber Set/2
Shock Absorber Joint Rubber Set/2. Replaces OEM # 52484-292-000
Master Cylinder Rubber Boot
Master Cylinder Rubber Boot. Replaces OEM # 45522-422-000
Handlebar Rubber Boot
Handlebar Rubber Boot. Replaces OEM # 53180-425-010
Speedo/Tachometer Meter Cushion
Speedo/Tachometer Meter Cushion, Replaces OEM # 37235-323-700
Carburetor Cap Screw Set/8
Carburetor Cap Screw Set/8 with Metal Washers.
Drive Chain Adjuster Set
Complete Drive Chain Adjuster Set, Includes 2 Chain Adjusters, 2 Chain Adjusting Bolts and 2 Adjuster Nuts. Replaces OEM # 40543-425-000
Fuse Box Assembly
Fuse Box Assembly Complete with 15Amp Fuses, Replaces OEM # 38200-MF9-405
Fuse Box Assembly
Fuse Box Assembly Complete with 10Amp Fuses, Replaces OEM # 38200-425-005
Carb Holder Set
Carb Holder Set (Set of 4). Replace those old cracked or dried up carb holders with a brand new set! Replaces OEM # 16211-460-770 X4. NOTE-If you require band clamps, these holders require our 50-52mm diameter band clamps part #15-0689 X8 or gear clamps #15-0670 X8 .
Helmet Holder Lock w Keys
Helmet Holder Lock with Keys, Replaces OEM # 50710-086-007
Primary Chain
OEM Quality Primary Chain, 50 Link. Replaces OEM # 92057-1011 / 23131-426-003 / 23131-323-003
Passenger Rear Footrest Rubber Set
Passenger Rear Footrest Rubber Set/2, Replaces OEM # 50716-371-660
Front Wheel Bearing Retainer Ring Tool
Front Wheel Bearing Retainer Ring Tool. High quality tool for removing and fitting the front wheel bearing retainer ring with 1/2 inch socket bar wrench tool hole. The perfect tool for easier removal and fitting without damaging the special retainer ring.
Rear Wheel Bearing Retainer Ring Tool
Rear Wheel Bearing Retainer Ring Tool. High quality tool for removing and fitting the rear wheel sprocket hub bearing retainer ring with 1/2 inch socket bar wrench tool hole. OR removing and fitting the rear wheel sprocket carrier bearing retainer ring. The perfect tool for easier removal and fitting without damaging the special retainer ring. Removes Rear Wheel Sprocket Carrier Bearing Retainer Ring on the Honda CB750K (1969-78), CB750F (1975-78) Supersport, CB750A (1976-78) Hondamatic Removes Rear Wheel Hub Bearing Retainer Ring on the Honda CB750K (1969-82), CB750A (1976-78) Hondamatic CB750C (1980-82) Custom, CB750L (1979) Limited CB650 (1979-82), CB650C (1980-81) Custom, CB650SC (1982) Nighthawk
Tachometer Cable
Tachometer Cable - OEM Ref # 37260-426-000 Made in Japan
Speedometer Cable
Speedometer Cable - OEM Ref # 44830-MA5-670 Made in Japan
Choke Cable
Choke Cable - OEM # 17950-426-000 Made in Japan
Starter Solenoid Relay
Starter Solenoid Relay with Fuse. Replaces OEM # 35850-MB0-007
Oil Pressure Switch
Oil Pressure Switch, Replaces OEM # 37240-P13-013
Carb Fuel Connector Tube and Accellerator Tube O-Rings
Carburetor Fuel Connector Tube and Accellerator Tube O-Rings, 12 O-Rings.
Stock Type Gearshift Lever Rubber
Stock Type Gearshift Lever Rubber, Replaces OEM # 24781-419-000
Brake Rod Joint
Brake Rod/Arm Joint, Replaces OEM # 95015-32001
Brake Rod Joint Pin w Cotter Pin
Brake Rod Joint Pin with Cotter Pin, Replaces OEM # 95015-52000 (Joint Pin) and OEM # 94201-16250 (Cotter Pin).
Brake Rod Adjusting Nut
Brake Rod Adjusting Nut, Replaces OEM # 95015-42000
Valve Stem Seal
Valve Stem Seal. Replaces OEM # 12209-333-005 / 12209-333-005 Sold Each - Order the Quantity you Require
Tach Drive Plug Block Off w O-Ring
Tach Drive Plug (Block Off) with O-ring. This plug is generally used when the tachometer cable drive is removed and still needs to be blocked off to prevent oil leakage. This plug has an o-ring groove machined in it for better sealing. Several bike builders just cut the stock cable off and left the Honda cable drive end installed in the valve cover. This plug is a much cleaner option in both functionality and looks. These plugs are a real nice touch when you are not using the stock tachometer, and need to eliminate the cable, or are using an electronic tach. Installs in about a minute, no need to remove the valve cover to remove the tach drive gear assy. Fits tachometer cables that are approximately 15mm in diameter with a 10.5mm groove and held in place with a screw.
Center Stand Spring Plate
Center Stand Spring Plate, This is the Plate the Center Stand Spring Attaches to. Replaces OEM # 50523-425-000
Side Stand Pivot Bolt & Nut Set
Side Stand Pivot Bolt & Nut Set, This is the Set Used to Fasten the Side Stand in Place. Replaces OEM # 90108-283-000 (Bolt) and 94002-10000-0S (Nut).
Rear Brake Shoe Spring Set/2
Rear Brake Shoe Spring Set of 2. Replaces OEM # 43151-346-000
Fuse Box Plate Cover Screw Set
Black Fuse Box Plate Cover Screw (Set of 2). Replaces OEM # 93700-05020-0G
Footrest Rubbers
Footrest Rubbers (Set/2) - OEM Ref # 50661-425-670
Wire Harness
Main Wire Harness Loom - OEM Ref # 32100-460-000 NOTE: These fit model years and type listed, other years and bikes use a different OEM part number (there is a difference!).
Brake Disc Retaining Nut Pk/10
Brake Disc Retaining Nut Pk/10, Replaces OEM # 90309-357-000
Brake Cam Dust Seal
Brake Cam Dust Seal, Replaces OEM # 43134-300-000
Fork Seal Stopper Metal Ring Pk/2
Fork Seal Stopper Metal Ring Pk/2, Replaces OEM # 51447-KL4-951 This is the Metal Ring above the Fork Seal.
Carb Top Gasket
Carburetor Top Gasket, Replaces OEM # 16014-393-004
Crank Seal
Crank Seal - 30 x 42 x 8 - Replaces OEM # 91201-300-003 Note: Please Reference the OEM Number and Seal size above to make sure this is the Crank Seal you Require. Some models use 2 Different Crank Seals.
Tach Drive Oil Seal
Tach Drive Oil Seal - 4.8 x 14.5 x 5 - Replaces OEM # 91256-425-003
Shift Shaft Oil Seal
Shift Shaft Oil Seal - 12.5 x 25 x 8 - Replaces OEM # 91204-425-003
Intake Valve
Intake Valve - Replaces OEM # 14711-426-003 Made in Japan
Exhaust Valve
Exhaust Valve - Replaces OEM # 14721-426-003 Made in Japan
Front Brake Caliper Bleed Screw
Front Brake Caliper Bleed Screw. Replaces OEM # 45224-413-003 Sold Each, Order the Quantity you Require
Handlebar Clutch Lever Pivot Bolt & Nut Set
Handlebar Clutch Lever Pivot Bolt & Nut Set. This is the Set that Fastens the Clutch Lever in Place. Includes One Bolt with One Nut. Replaces OEM # 90113-422-000 (Bolt) and OEM # 94002-06000-0S (Nut).
Piston Ring Set (Standard Size)
Standard Size Piston Ring Set Ring Set OEM Ref # 13011-426-004 (Std.) Japanese made Superior Quality Note: This Set includes piston rings to rebuild one piston, 4 Sets are needed to rebuild all pistons.
Handlebar Brake Lever Pivot Bolt Set
Handlebar Brake Lever Pivot Bolt, Washer & Nut Set. This is the Set that Fastens the Brake Lever in Place. Includes One Bolt with One Washer and Nut. Replaces OEM # 90114-422-000 (Bolt).
Handlebar Brake Lever Pivot Bolt & Nut Set
Handlebar Brake Lever Pivot Bolt & Nut Set. This is the Set that Fastens the Brake Lever in Place. Includes One Bolt with One Nut. Replaces OEM # 90114-MA5-671 (Bolt) and OEM # 94050-06000 (Nut)