Honda ► CB750A ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB750A with universal parts included that match “honda sl125”►
- Honda
Replacement Mirror
Replacement Mirror (R.H) 4 1/2" Diameter, 10mm Thread. Replaces OEM# 88110-333-611
Rear Wheel Bearing Retainer
Rear Wheel Bearing Retainer - Sprocket Side - Replaces OEM# 41231-283-000 This retainer is used on the (sprocket side) of the bike.
Performance Main Jet Kit
Performance Main Jet Kit. Kit includes a total of 16 Main Jets for Keihin Carbs. Use this jet kit to unleash the extra power you should have from your aftermarket exhaust, flee flowing air filters or any engine mods you have made. Kit includes Main Jets #105 (X4), #110 (X4), #115 (X4) and #120 (X4).
Speedo/Tach Cap Nut Set/4
Set of 4 Cap Nuts Used to Mount the Stock OEM Type Speedometer and Tachometer. Replaces OEM # 94021-06020 X4.
Throttle Cable - Pull
Throttle Cable "Pull Type" - OEM Ref. # 17910-393-770 Made in Japan
Throttle Cable - Push
Throttle Cable "Push Type" - OEM Ref. # 17920-393-770 Made in Japan
Cam Chain
Cam Chain 219T x 94 D.I.D (Daido) Takes 01-8803 Rivet Link Pitch: .3061" Side Plate: Peanut Average Tensile Strength: 1800lbs OEM Ref # 14401-286-003 / 14401-410-003
CB750A 1977-78 Speedo Face Plate & Gear Indicator Decal Set ~ KM/H
Speedometer Face Plate (Like Original) & Gear Indicator & Fuel Meter Decal (Sticker) Set ~ KM/H Type. Disassembly of speedometer and tachometer is required. Decals come uncut. Removal of original information printed on OEM plastic face is required prior to application of these decals. All blue/green areas are the plastic face showing through. All decals and face plates are "printed" in the United Kingdom on the highest quality materials. Every detail has been designed very accurately to achieve an exact copy of the original face plates. With this set you are able to restore your gauges to the manufacturers standards.
Brake Rod Joint Pin w Cotter Pin
Brake Rod Joint Pin with Cotter Pin, Replaces OEM # 95015-52000 (Joint Pin) and OEM # 94201-16250 (Cotter Pin).
Brake Rod Adjusting Nut
Brake Rod Adjusting Nut, Replaces OEM # 95015-42000
Carb Top Gasket
Carburetor Top Gasket, Replaces OEM # 16014-393-004
Front Brake Caliper Bolt & Washer Set
Front Brake Caliper Bolt & Washer Set. Set includes 2 Bolts and 2 Washers. Replaces OEM # 90165-323-000
Front Master Cylinder Reservoir Diaphragm
Front Master Cylinder Reservoir Diaphragm. Replaces OEM # 45520-300-000
CB Black Mirror - Original Type (Left Side)
Gloss Black CB Style Left Side Mirror - 4 1/2" Diameter with 10mm. RH Thread & 7" Stems.
CB Black Mirror - Original Type (Right Side)
Gloss Black CB Style Right Side Mirror - 4 1/2" Diameter with 10mm. RH Thread & 7" Stems.
Gas/Fuel Tank Cap
OEM Style Gas/Fuel Tank Cap with Rubber Gasket Already Installed, Replaces OEM # 17620-399-010 Note: Does not include a chain attached to this cap.
Rear Wheel Damper Rubber
Rear Wheel Drive Damper Rubber, Replaces OEM # 41241-300-050 These fit between the rear wheel sprocket hub and the wheel hub and get worn down over time from use. Note: 4 Used Per Bike, Order The Quantity you Require
Rear Shock Swingarm Bushing
Rear Shock Swingarm Bushing, Replaces OEM# 40548-268-000 19mm Long, 22mm OD, 10mm ID. Sold Each, Order the Quantity you Require
Primary Chain
OEM Quality Primary Chain - 50 Link OEM Ref # 13610-393-004
Turn Signal Lamp
Turn Signal Lamp - Front 2-Wire OEM Ref # 33400-377-671 / 33400-460-671 / 33400-460-679
Ignition Coil
Ignition Coil Stock type for contact point ignitions. 100mm center to center mounting points. OEM Ref # 30501-300-03 / 30501-300-013 / 30502-300-003 / 30502-300-013
Fuel Petcock
Fuel Petcock OEM Ref # 16950-393-015 Fits M16 x 1.5 Note: Please Check that the Size Listed Above is Correct for your Bike before ordering
Swingarm Pivot Bolt Locknut with Washer
Swingarm Pivot Bolt Locknut with Locknut Washer. Replaces OEM # 90354-268-000 (Locknut) and OEM # 90526-268-000 (Washer).