Honda ► CB750C ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB750C►
- Honda
Front Brake Caliper Piston Sealing Ring
Front Brake Caliper Piston Sealing Ring, Replaces OEM # 45108-300-003
Front Brake Caliper Piston Sealing Ring
Front Brake Caliper Piston Sealing Ring, Replaces OEM # 45215-533-004
Front Brake Caliper Piston
Front Brake Caliper Piston, 42.8mm OD x 36.5mm Height. Replaces OEM # 45107-425-003
Speedo Gear Plug
Speedo Gear Plug - Plug 15mm Outer Diameter, 22mm Long. This Plug is Great for Keeping your Original Speedo Drive Gear Clean.
Rear Brake Shoes
Rear Brake Shoes Pk/2 Diameter: 178.5mm Width: 39mm OEM Ref # 43120-393-006
Front Brake Pads
Front Brake Pads Pk/2 OEM Ref # 45105-425-006
Front Sintered Metal Brake Pad Set
Brake Pad Set - Sintered Metal - 52.4 x 52.5 x 12mm OEM # 45105-425-003 / 45105-425-006 / 45105-471-006 / 45105-MA5-671 Set=1 Caliper
Deluxe Rear Brake Shoe Set
Deluxe Kevlar/Carbon Water Grooved Rear Brake Shoe (Set/2) - OEM Ref # 06430-393-405
Brake Rod Spring
Brake Rod Spring. Replaces OEM # 95014-73100
Cam Chain Tensioner Spring "A"
Cam Chain Tensioner Spring "A". This is the Cam Chain Tensioner Spring for the Larger Main Cam Chain Tensioner ("A"). Replaces OEM # 14514-425-010
Headlight Adjusting Screw & Spring Set
Headlight Adjusting Screw & Spring Set. Each Set Includes One Screw and One Spring. Replaces OEM # 33103-346-670 (Screw) and OEM # 33107-300-003 (Spring)
Steering Stem Head Lock Nut
Steering Stem Head Top, Thread on Lock Nut. Replaces OEM # 90302-425-830
Lever Safety Stop Switch
Front Clutch Lever Safety Stop Switch, Replaces OEM # 35330-413-003 This is the switch that allows the bike to start when the clutch lever is depressed.
Clutch Adjuster Bolt
Clutch Adjuster Bolt, Replaces OEM# 22841-425-000
Special Clutch Washer
Special Angled Clutch Washer (16mm), Replaces OEM# 90481-292-000
Center Stand Spring
Center Stand Spring. Replaces OEM # 95014-71702
Progressive Type Front Fork Springs
Progressive Type Front Fork Spring Set/2. Includes 10" Pipe and Washers. These Progressive Type Springs improve handling and overall ride quality. They Stop front end droop and diving during braking while improving cornering stability. A Great Performance upgrade for your Bike! Some Bikes Require that the Spacer Length be Calculated using the instructions below then the Included Pipe Cut to make the Appropriate Sized Spacers, Some Models Do Not Require Spacers. Be Sure to Check the End of the Installation Instructions Below to see if your Bike Require Spacers.
Clutch Center Nut Removal Tool
Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Inside diameter 24mm, use with 3/8" driver.
Clutch Center Nut Removal Tool ~ Premium
Premium Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Both ends with 1/2 drive extension bar, Diameter 20 x 24.
Clutch Plate
Clutch Plate 1 Piece Required OEM Ref # 22202-425-000 / 22202-MT8-000
Clutch Plate
Clutch Plate 7 Pieces Required OEM Ref # 22201-425-000 / 22201-MN5-020 / 22201-MT8-000 / 13088-030
Steel Clutch Plate "B" ~ Riveted Plate
Steel Clutch Drive Plate "B" - OEM Ref # 22322-425-000 This is the thick double steel plate with rivets in it. It is an essential part of any clutch rebuild as the rivets are known to wear over time. 1PC Required per Bike
Steel Clutch Plate
Steel Clutch Plate 6 Pieces Required
Clutch Spring Kit
Clutch Spring Kit
Intake Carb Holder Set
Intake Carb Holder Set OEM Ref # 16214-425-00 1 Pc, 16213-425-00 1 Pc, 16212-425-00 1 Pc, 16211-425-00 1 Pc NOTE-If you require band clamps, these carb holders require our clamps part #15-0689 X8
Float Bowl Drain Screw O-Rings Pk/4
Float Bowl Drain Screw O-Rings Pk/4
Carb Rebuild Kit
Carb Rebuild Kit Includes Items Pictured High Quality - Made In Japan 1 Kit Needed Per Carb
Carb Rebuild Kit
Carb Rebuild Kit Includes Items Pictured High Quality - Made In Japan 1 Kit Needed Per Carb
Performance Main Jet Kit
Performance Main Jet Kit. Kit includes a total of 16 Main Jets for Keihin Carbs. Use this jet kit to unleash the extra power you should have from your aftermarket exhaust, flee flowing air filters or any engine mods you have made. Kit includes Main Jets #105 (X4), #110 (X4), #115 (X4) and #120 (X4).
Ultimate Performance Main Jet Kit
Ultimate Performance Main Jet Kit. Kit includes a total of 44 Main Jets for Keihin Carbs. Use this jet kit to unleash the extra power you should have from your aftermarket exhaust, flee flowing air filters or any engine mods you have made. Kit includes Main Jets #100 (X4), #102 (X4), #105 (X4), #108 (X4), #110 (X4), #112 (X4), #115 (X4), #118 (X4), #120 (X4), #122 (X4) and #125 (X4)
Pilot Jet Set/4
Stock Type Pilot Jet Set of 4 (Size #35). Pilot Jets (your idle and low speed operation) are critical for smooth idling and lower rpm driving. When rebuilding carbs it is highly recommended to replace these pilot jets to ensure your bike is running as well as possible. Note: These Pilot Jets (#35) were the standard size equipped from the factory
Rubber Passage Plug
Rubber Passage Plug Pk/5 OEM Ref # 16010-425-671 / 16010-461-781 / 16010-469-004
Float Needle
Float Needle High Quality - Made In Japan OEM Ref # 16155-413-751 / 16155-397-971
Float Bowl Drain Screw
Float Bowl Drain Screw w O-Ring. Note: We sell these each, order the quantity you require
Air Screw Needle O-Ring
Air Screw Needle O-Ring. 2.8mm x 1.2mm. Note: sold each, order the quantity you require
Air Cut Off Valve With Cover
Carb Air Cut Off Valve with Cover - OEM # 16048-429-771 (Diaphragm), 16048-425-771 (Spring + 1 O-Ring), 16048-429-771 (Cover).
Float Bowl Screws Pk/2
Float Bowl Screws with Lock Washers, Pack of 2 Screws and 2 Washers. These fasten the float bowl in place. Replaces OEM # 93892-04016-00 Order Quantity of Screws you Require
Side Cover Emblem
Side Cover Emblem with 2 Attachment Clips. Replaces OEM# 87127-425-730 Note: 2 Emblems Used Per Bike, Order the Quantity you Require
Lens Screw
Tail Light Lens Screws, Pack of 10 Screws. Replaces OEM # 93500-04055-4J ISO Std. Pitch - Steel Plated Size: 4 x 55mm
Speedometer / Tachometer Glass Lens Rubber Seal
Speedometer or Tachometer Glass lens Rubber Seal. This seal is used when replacing the glass on the Speedo or Tach. Fits: All 92mm (3.6") glass lenses. Sold each, order the quantity you require
Speedometer / Tachometer Internal Rubber Seal
Speedometer / Tachometer Internal Rubber Seal. This internal rubber seal replaces the ripped, dried or missing rubber internal seal. This internal rubber seal fits to any stock type Honda CB750 ND brand gauges.
Side Cover Emblem Attachment Nut
Side Cover Emblem Attachment Nut, Replaces OEM# 90315-504-000 Sold Each, Order the Quantity you Require
Shock Absorber Washer
Shock Absorber Washer, Used when Installing Shocks. Replaces OEM # 90521-292-000 Note: Washers sold Each, order the quantity you require
Shock Absorber Nut
Shock Absorber Nut, Used when Installing Shocks. Replaces OEM # 90309-315-000 Note: Nuts sold Each, order the quantity you require
OEM Type Shock Absorber Bolt
Chrome Shock Absorber Bolt, Replaces OEM # 93201-10032-0B / 93200-10032-0A Note: 2 Bolts Used Per Bike, Order the Quantity you Require
Speedo/Tach Cap Nut Set/4
Set of 4 Cap Nuts Used to Mount the Stock OEM Type Speedometer and Tachometer. Replaces OEM # 94021-06020 X4.
Side Stand Spring
Side Stand Spring, Replaces OEM # 95014-72402
NGK Spark Plug
NGK D8EA Spark Plug - Standard Original CB750 Spark Plug 4 required per CB750, Order the quantity you require.
NGK Spark Plug
NGK DR8ES-L Spark Plug
NGK Iridium Spark Plug
NGK DR8EIX Iridium Spark Plug Cheapest Horsepower You Can Buy for your CB! Adds a Solid 1-2 HP to your Bike! 4 required per bike, Order the Quantity you require.