Honda ► CB750C ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB750C that match “1”►
- Honda
Piston Ring Set - 1st Oversize (0.25mm.)
1st Oversize Piston Ring Set + 0.25mm. Ring Set OEM Ref. # 13021-425-004 Japanese made Superior Quality Note: This Set includes piston rings to rebuild one piston, 4 Sets are needed to rebuild all pistons.
Carburetor Air Mixture Screw Kit
Carburetor Air Mixture Screw Kit Set Includes 1 Mixture Screw, 1 Spring, 2 O-Rings. Order The Quantity of Sets you Require.
Camshaft Holder Seal
1pc. Camshaft holder Rubber Seal (triangular pc. with rounded corners) OEM Ref. # 91311-425-000 - 1 pc. required per Engine
Replacement Headlamp Assembly
Chrome Replacement Headlamp Assembly (6 1/4") Replaces Rim, Retainer, Lens, Bulb & Bucket
Drain Plug Washer
Drain Plug Washer 14mm x 20mm x 1mm
Intake Carb Holder Set
Intake Carb Holder Set OEM Ref # 16214-425-00 1 Pc, 16213-425-00 1 Pc, 16212-425-00 1 Pc, 16211-425-00 1 Pc NOTE-If you require band clamps, these carb holders require our clamps part #15-0689 X8
Starter Motor Seal
Starter Motor Seal - 60 x 1.4 - Replaces OEM# 31206-286-158 / 31206-402-008
Brake Lever
Brake Lever OEM Ref # 53175-KM9-006 / 53175-ML5-006 / 53175-MR1-671
Replacement Headlamp
Chrome Replacement Headlamp Assembly (6 1/4") - Diamond Cut Lamp Replaces Rim, Retainer, Lens, Bulb & Bucket
Replacement Headlamp Assembly ~ Gloss Black
Gloss Black / Chrome Ring Replacement Headlamp Assembly (6 1/4") Replaces Rim, Retainer, Lens, Bulb & Bucket
Turn Signal Lamp
Turn Signal Lamp 1-Wire - Rear OEM Ref # 33400-377-671 / 33400-460-671 / 33400-460-679
Oil Drain Plug
Magnetic Oil Drain Plug 14mm Diameter 1.5 Thread Pitch OEM Ref # 92800-14000 / 90101-14259-00
Exhaust Gasket (Each)
Exhaust Gasket - 1 Pc OEM Ref # 18291-254-000 / 18291-MM5-860 Sold Each, Order the Quantity you Require
Athena Engine Gasket Set
Complete Engine Gasket Set Includes all Engine Gaskets High Quality - Made In Italy by Athena Athena Product # P400210850700/1
Exhaust Headpipe Gasket (Each)
Cylinder Head to Exhaust Headpipe Gasket (1 Pc.) OEM Ref. # 18291-MM5-860 Sold Each, Order the Quantity you Require
Clutch Plate
Clutch Plate 1 Piece Required OEM Ref # 22202-425-000 / 22202-MT8-000
Carb Rebuild Kit
Carb Rebuild Kit Includes Items Pictured High Quality - Made In Japan 1 Kit Needed Per Carb
Carb Rebuild Kit
Carb Rebuild Kit Includes Items Pictured High Quality - Made In Japan 1 Kit Needed Per Carb
Air Screw Needle O-Ring
Air Screw Needle O-Ring. 2.8mm x 1.2mm. Note: sold each, order the quantity you require
Rear Brake Light Stop Switch Spring
Rear Brake Light Stop Switch Spring. This is the Spring that Attaches to the Rear Stop Light Switch. Replaces OEM # 35357-ME1-670
Starter Brush Set
Starter Brush Set/2 1Pc Insulated Leads 1Pc Non-Insulated Leads 12mm x 14mm x 6mm For Misuba 2 Brush Starter. OEM Ref # 31201-292-158 / 31201-MG9-004
Alternator Stator
Alternator Stator OEM Ref # 31120-425-852 / 31120-425-871 / 31120-MG1-000 / 31120-MG1-005 / 31120-MG5-005 / 31120-461-415 / 31120-461-405 / 31120-461-671 / 31120-461-005 / 31120-426-005 / 31120-426-832
Rectifier Regulator
Rectifier Regulator 8 Wire (1 Four Prong Plug With 3 Wires, 1 Six Prong Plug With 5 Wires) OEM Ref # 31600-461-771 / 31600-MA6-000 / 08154-4610012 / 31600-425-008 / 31600-MA6-910
DOHC Screw Set
71PC DOHC Screw Set, Includes Front Stay Plate Screws (8), CV Cap Screws (8), Throttle Cable Bracket Screw (1), Rear Stay Plate Screws (8), Vacuum Petcock Screws (6), Bowl Screws (12), Accelerator Pump Cover Screws (3), Air Cutoff Screws (8), Choke Cable Clamp Screw (1), Throttle Plate Screws (8) and Choke Plate Screws (8).
Starter Motor Seal
Starter Motor Seal - Size 24.4 x 3.1, Replaces OEM# 91312-MG7-003 / 91309-300-000 / 91309-425-003
Cam Chain Tensioner "B"
Cam Chain Tensioner "B" - Replaces OEM# 14530-MG5-670 / 14530-425-000 / 14530-425-010 / 14530-MG1-670. Note: This is the smaller tensioner on these bikes.
Chain Adjuster Stopper Set/2
Chain Adjuster Stopper Set/2. High quality steel made in Canada stoppers. These have been discontinued by Honda get these steel upgrades today! Replaces OEM# 52136-405-000 and 52136-ME1-670.
Ignition Coil
Ignition Coil 1.9ohm Primary, 13.4K ohm Secondary Can be Used With Contact Point Ignitions OEM Ref # 30500-422-003 / 30500-422-013 / 30510-MA6-013
Fuel Petcock
Fuel Petcock - OEM Ref. # 16950-425-025 Fits M16 x 1.5 Note: Please Check that the Size Listed Above is Correct for your Bike before ordering
Fuel Petcock
Fuel Petcock - OEM Ref. # 16950-MA4-671 / 16950-461-771 Fits M18 x 1.0 Note: Please Check that the Size Listed Above is Correct for your Bike before ordering
Fuel Petcock
Fuel Petcock - OEM Ref. # 16950-461-751 Fits M20 x 1.0 Note: Please Check that the Size Listed Above is Correct for your Bike before ordering
Front Sintered Metal Brake Pad Set
Brake Pad Set - Sintered Metal - 52.4 x 52.5 x 12mm OEM # 45105-425-003 / 45105-425-006 / 45105-471-006 / 45105-MA5-671 Set=1 Caliper
Clutch Center Nut Removal Tool ~ Premium
Premium Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Both ends with 1/2 drive extension bar, Diameter 20 x 24.
Steel Clutch Plate "B" ~ Riveted Plate
Steel Clutch Drive Plate "B" - OEM Ref # 22322-425-000 This is the thick double steel plate with rivets in it. It is an essential part of any clutch rebuild as the rivets are known to wear over time. 1PC Required per Bike
Air Cut Off Valve With Cover
Carb Air Cut Off Valve with Cover - OEM # 16048-429-771 (Diaphragm), 16048-425-771 (Spring + 1 O-Ring), 16048-429-771 (Cover).
NGK Iridium Spark Plug
NGK DR8EIX Iridium Spark Plug Cheapest Horsepower You Can Buy for your CB! Adds a Solid 1-2 HP to your Bike! 4 required per bike, Order the Quantity you require.
Front Wheel Bearing Retainer Ring Tool
Front Wheel Bearing Retainer Ring Tool. High quality tool for removing and fitting the front wheel bearing retainer ring with 1/2 inch socket bar wrench tool hole. The perfect tool for easier removal and fitting without damaging the special retainer ring.
Steering Stem Head Lock Nut
Steering Stem Head Top, Thread on Lock Nut. Replaces OEM # 90302-425-830
Handlebar Brake Lever Pivot Bolt & Nut Set
Handlebar Brake Lever Pivot Bolt & Nut Set. This is the Set that Fastens the Brake Lever in Place. Includes One Bolt with One Nut. Replaces OEM # 90114-MA5-671 (Bolt) and OEM # 94050-06000 (Nut)
Rear Wheel Bearing Retainer Ring Tool
Rear Wheel Bearing Retainer Ring Tool. High quality tool for removing and fitting the rear wheel sprocket hub bearing retainer ring with 1/2 inch socket bar wrench tool hole. OR removing and fitting the rear wheel sprocket carrier bearing retainer ring. The perfect tool for easier removal and fitting without damaging the special retainer ring. Removes Rear Wheel Sprocket Carrier Bearing Retainer Ring on the Honda CB750K (1969-78), CB750F (1975-78) Supersport, CB750A (1976-78) Hondamatic Removes Rear Wheel Hub Bearing Retainer Ring on the Honda CB750K (1969-82), CB750A (1976-78) Hondamatic CB750C (1980-82) Custom, CB750L (1979) Limited CB650 (1979-82), CB650C (1980-81) Custom, CB650SC (1982) Nighthawk
Oil Filter Washer - Each
Oil Filter Washer - Each 30mm OD - 20.5mm ID - .5mm Thickness Replaces OEM# 15414-300-000 Sold Each, Order the Quantity you Require
Oil Pressure Switch
Oil Pressure Switch, Replaces OEM # 37240-P13-013
Progressive Type Front Fork Springs
Progressive Type Front Fork Spring Set/2. Includes 10" Pipe and Washers. These Progressive Type Springs improve handling and overall ride quality. They Stop front end droop and diving during braking while improving cornering stability. A Great Performance upgrade for your Bike! Some Bikes Require that the Spacer Length be Calculated using the instructions below then the Included Pipe Cut to make the Appropriate Sized Spacers, Some Models Do Not Require Spacers. Be Sure to Check the End of the Installation Instructions Below to see if your Bike Require Spacers.
Clutch Plate
Clutch Plate 7 Pieces Required OEM Ref # 22201-425-000 / 22201-MN5-020 / 22201-MT8-000 / 13088-030
Oil Passage Cap with O-Ring
Oil Passage Cap with O-Ring. Replaces OEM # 15331-300-000 (Oil Passage Cap) and OEM # 94608-40000 (O-Ring). Note: Sold Each, Order the Quantity of Caps you Require
Speedo Gear Plug
Speedo Gear Plug - Plug 15mm Outer Diameter, 22mm Long. This Plug is Great for Keeping your Original Speedo Drive Gear Clean.
Brake Rod Joint
Brake Rod/Arm Joint, Replaces OEM # 95015-32001
Chrome Spin On Oil Filter
Chrome Spin On Oil Filter Replaces Stock OEM Housing, Filter Bolt and Paper Element Filter. Note: When installing screw in the threaded bung first and then install the filter onto the bung.
Front Wheel Bearing Retainer
Front Wheel Bearing Retainer - Replaces OEM# 44643-300-000
Throttle Sleeve
Nylon Throttle Sleeve - Replaces OEM # 53141-300-010