Honda ► CB750F ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB750F►
- Honda
Rear Sintered Metal Brake Pad Set
Rear Brake Pad Set - Sintered Metal - 67 x 49.5 x 9.5mm. OEM # 45105-410-305 / 45105-461-771 / 45105-461-772 / 45105-438-004 / 45105-438-007 / 45105-438-008
Kick Starter Joint Spring
Kick Starter Joint Spring. This Spring Goes onto the Kick Starter Knuckle Pin (The Pin that Connects the Kick Starter to the Bike). Replaces OEM # 28292-250-010
Clutch Lever Return Spring
Clutch Lever Return Spring. This is the Spring Located Behind the Clutch Cover. Replaces OEM # 22815-300-000
Headlight Adjusting Screw & Spring Set
Headlight Adjusting Screw & Spring Set. Each Set Includes One Screw and One Spring. Replaces OEM # 33103-346-670 (Screw) and OEM # 33107-300-003 (Spring)
Rear Sprocket Washer Set
Rear Sprocket Tongued Lock Washer (Pack of 2). Replaces OEM # 94108-17000
Kick Starter Stopper Spring with Steel Ball
Kick Starter Stopper Spring with Steel Ball Set. Replaces OEM # 28333-300-000 (Spring) and OEM # 96211-08000 (Steel Ball).
Flange Knock Bolt (Set/2)
Flange Knock Bolt (Set/2). These Bolts Fasten to the Cam Sprocket. Replaces OEM # 90082-HA0-000
Swingarm Pivot Bolt Locknut with Washer
Swingarm Pivot Bolt Locknut with Locknut Washer. Replaces OEM # 90354-268-000 (Locknut) and OEM # 90526-268-000 (Washer).
Rear Sprocket Bolt & Nut Set
Rear Sprocket Stud Bolt (12x54) & Nut Set. Set includes 4 Stud Bolts and 4 Nuts. These Stud Bolts Fasten to the Centre Wheel Flange and Rear Sprockets. Replaces OEM # 90128-341-000 X4 (Bolts), 94030-12000 X4 (Nut)
Brake Rod Pin
Brake Rod Pin, Replaces OEM# 46503-371-000
Special Clutch Washer
Special Angled Clutch Washer (16mm), Replaces OEM# 90481-292-000
Kick Starter Return Spring
Kick Starter Return Spring. Replaces OEM # 28261-300-010
Master Cylinder Rubber Boot
Master Cylinder Rubber Boot. This Boot Attaches to where the Brake Hose Joins to the Master Cylinder. Replaces OEM # 45522-300-010
Center Stand Spring
Center Stand Spring. Replaces OEM # 95014-71702
Clutch Center Nut Removal Tool
Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Inside diameter 24mm, use with 3/8" driver.
Clutch Center Nut Removal Tool ~ Premium
Premium Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Both ends with 1/2 drive extension bar, Diameter 20 x 24.
Clutch Spring Set
Clutch Spring Set
Clutch Plate
Clutch Plate 6 Pieces Required OEM Ref # 22201-300-000 / 22201-371-000
Clutch Plate
Clutch Plate 1 Piece Required .138" Thickness OEM Ref # 22202-371-000 / 22202-390-000 / 22202-392-000
Steel Clutch Plate
Steel Clutch Plate 5 Pieces Required OEM Ref # 22321-283-000 / 22321-MG8-000
Carb Holder Set
Carb Holder Set (Set of 4). Replace those old cracked or dried up carb holders with a brand new set! Each holder is numbered 1-4 just like the original OEM holders. Replaces OEM #'s 16211-410-000 / 16212-410-000 / 16213-410-000 / 16214-410-000 NOTE-If you require band clamps, these carb holders require our 45-47mm diameter clamps part #15-0688 X8.
Float Bowl Drain Screw O-Rings Pk/4
Float Bowl Drain Screw O-Rings Pk/4
Carb Rebuild Kit
Carb Rebuild Kit. Contains: Float Bowl Gasket, Carb Top Gasket, D313 Slide Needle, Main Jet (#105, Stock type for 1977-78F models), Main Jet #110, Stock type for 1978K model), Float Needle, Air Spring, Air Screw Plug, E-Clip, Air Fuel Screw (1978F Type), Air Fuel Screw (1977-78K Type), Needle Jet, Metal Washer, 6 O-Rings. - Made in Japan -
Carb Rebuild Kit
Carb Rebuild Kit Includes Items Pictured High Quality - Made In Japan 1 Kit Needed Per Carb
Performance Main Jet Kit
Performance Main Jet Kit. Kit includes a total of 16 Main Jets for Keihin Carbs. Use this jet kit to unleash the extra power you should have from your aftermarket exhaust, flee flowing air filters or any engine mods you have made. Kit includes Main Jets #105 (X4), #110 (X4), #115 (X4) and #120 (X4).