Honda ► CB750F ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB750F with universal parts included►
- Honda
Foam Round Pod Air Filter ~ Slightly Blemished
42mm Round Foam Pod Air Filter With Chrome End Caps and Rubber Mouth - Circular style. These units were blemished slightly at the factory. The top chrome cap is chromed perfectly but the ring at the bottom in error was not chromed so has a flat steel look and seems to have some glue like residue. You should be able to clean this glue area off and polish it up a bit and get a great deal on these while your at it! Please Double check you require 42mm Pod Filters before purchasing
Oil Filter Bolt
Oil Filter Bolt OEM Ref # 15420-333-000 / 92003-094 / 92003-193 / 92001-1074
Replacement Mirror
Replacement Mirror (R.H) 4 1/2" Diameter, 10mm Thread. Replaces OEM# 88110-333-611
Replacement Mirror
Replacement Mirror (L.H) 4 1/2" Diameter, 10mm Thread. Replaces OEM# 88120-333-611
CB Black Mirror - Original Type (Left Side)
Gloss Black CB Style Left Side Mirror - 4 1/2" Diameter with 10mm. RH Thread & 7" Stems.
CB Black Mirror - Original Type (Right Side)
Gloss Black CB Style Right Side Mirror - 4 1/2" Diameter with 10mm. RH Thread & 7" Stems.
Exhaust Gasket (Each)
Exhaust Gasket - 1 Pc OEM Ref # 18291-254-000 / 18291-MM5-860 Sold Each, Order the Quantity you Require
Exhaust Gasket Pk/10
Exhaust Gasket Pk/10 OEM Ref # 18291-254-000 / 18291-MM5-860
Headpipe to Collector Gasket
Headpipe to Collector Gasket 35mm x 41mm x 25mm OEM Ref # 18391-310-000
Ignition Coil
Ignition Coil Stock type for contact point ignitions. 100mm center to center mounting points. OEM Ref # 30501-300-03 / 30501-300-013 / 30502-300-003 / 30502-300-013
Seat Cover
Replacement Seat Cover with Reinforced Passenger Strap (No hardware included just re-use existing hardware). There is not a "Honda" stencil on the rear of the cover due to copyright. There is a layer of foam sewn into the top of the seat cover to improve ride comfort and smooth out any defects in your seat foam. Each seat cover is made entirely by hand in North America, it is crafted slowly with great care by a gifted master upholster, using only the top grade materials available. Comes with complete installation instructions as well as step by step instructions on how to repair damaged seat foam. Fits: the Original Stock Honda CB750F (1975-78) Supersport Seat This is for the SEAT COVER, Not the Full Seat, Photo Shows Seat Cover Installed for reference
Athena Engine Gasket Set
Complete Engine Gasket Set Includes all Engine Gaskets High Quality - Made In Italy by Athena Athena Product # P400210850701
Athena Gasket Set (Top End Set Only)
Athena Top End Gasket Set - Fits: All Honda CB750's (1974-78) Sets made by Athena of Italy the European original equipment supplier to Yamaha, Honda, Kawasaki, Suzuki and all major Italian bike makers. Top Quality ISO-9000 approved. Set includes: 18-7001, Cylinder Base Gasket, OEM # 12191-300-030 18-7002, Cylinder Head Gasket, OEM # 12251-300-050 18-7003, Cam Cover Gasket, OEM # 12391-300-400 18-7068, Cylinder Sleeve O-Ring Gasket Set/4, OEM # 91304-286-000 18-7015, Cylinder Head Nut Cover Set/6, OEM # 91318-300-013 18-7018, Cylinder Stud Packing Set/8, OEM # 12115-300-000 18-7069, Valve Tappet Cover Gasket Set/4, OEM # 91302-001-020 18-7017, Valve Stem Seal Set/8, OEM # 12209-300-000 18-7013, Exhaust Headpipe Gasket Set/4, OEM # 18291-MM5-860
Overhaul Gasket Set
Overhaul Engine Gasket Set Set contains: 18-7001 Cylinder Base Gasket, 18-7002 Cylinder Head Gasket, 18-7003 Cam Cover Gasket, 18-7004 Oil Pan Gasket (Late), 12-5038 Alternator (Dyno) Cover Gasket, 18-7006 Shift Cover Gasket, 12-5037 Clutch cover Gasket, 18-7008 Oil Pump Gasket, 18-7009 Cam Chain Tensioner Gasket, 18-7010 Point Plate Cover Gasket, 18-7011 Starter Motor Cover Gasket, 17-3812 -4pc. Exhaust Headpipe Gaskets, 18-7014 O-Ring for Breather Cover, 18-7068 4 pc. Cylinder Sleeve Base O-Rings, 01-0131 8 pc. Valve stem seals, 18-7018 8 pc. rubber cylinder stud packings. Set does Not contain Engine Oil Seals - See Oil Seal Set Listings Below.
Cylinder Base Gasket
Cylinder Base Gasket - OEM Ref. # 12191-300-030
Premium Athena Cylinder Head Gasket
Premium Athena Brand Cylinder Head Gasket - OEM Ref.# 12251-300-050
Cam Cover Gasket
Cam Cover Gasket - OEM Ref. # 12391-300-400
Oil Pan Gasket (Late)
Oil Pan Gasket (Late Type) - OEM Ref. # 11398-300-303
Shifter Cover Gasket
Shifter Cover Gasket - OEM Ref. # 11395-300-303 / 11395-300-306
Oil Pump Gasket
Oil Pump Gasket - OEM Ref. # 15135-300-010
Cam Chain Tensioner Gasket
Cam Chain Tensioner Gasket - OEM Ref. # 14592-300-000
Point Plate Gasket
Contact Point Plate Cover Gasket - OEM Ref. # 30372-300-300
Starter Motor Cover Gasket
Starter Motor Rubber Cover Gasket - OEM Ref. # 31282-300-020
Exhaust Headpipe Gasket (Each)
Cylinder Head to Exhaust Headpipe Gasket (1 Pc.) OEM Ref. # 18291-MM5-860 Sold Each, Order the Quantity you Require
Cam Cover Breather Gasket
Cam Cover Breather Gasket (O-Ring) - OEM Ref. # 12329-300-020
Cylinder Stud Packing Set (8pc)
8pc. set of rubber cylinder head bolt (stud) packings (short tubular rubber seals that fit over dowels) OEM Ref. # 12115-300-000
Cylinder Sleeve O-Ring Gasket Set
Cylinder Sleeve O-Rings (Set of 4) OEM Ref. # 91304-286-000 - 4 pc. required per Engine
Valve Tappet Cover Gasket Set/8
Valve Tappet Cover Gaskets Set/8. These are made for the stock type Valve Tappet Covers. These replace OEM # 91302-001-020 Note:These will only work on OEM type Tappet covers
Gear Change Lever
Gear Change Lever Universal Fit
Gear Change Lever
Gear Change Lever Universal Fit Spline Diameter 11.5mm Total Length 5 1/8" Offset 1 3/8"
Gas Cap Rubber Seal
Gas Cap Rubber Seal, Replaces OEM # 17631-329-003
Accelerator Pump Joint Hose
Accelerator Pump Joint Hose. 12" Piece. 8mm Outer Diameter, 4mm Inner Diameter. Order the quantity you require. Note: Be sure to remove and then re-install the old brass nozzles from the old joint hoses.
Carb Overflow Tube Hose
Carb Overflow Tube Hose. 24" Piece. 8mm Outer Diameter, 4mm Inner Diameter. Sold Each, Order the quantity you require
Carb Float
Carb Float with Pin, Replaces OEM # 16013-405-004 / 16013-393-004 / 16013-KCY-670 / 16013-MN1-671 Note: Order the Quantity of Floats you Require
Float Bowl Gasket
Float Bowl Gasket (O-Ring)
Carb Pump Diaphragm
Carb Pump Diaphragm OEM Ref # 16021-393-004 / 16021-393-014 / 16021-MC9-771
Steel Rear Sprocket - 43 Tooth X 630 Type
Steel Rear Sprocket - 43 Tooth - Replaces OEM # 41201-410-000 For 630 Chain Setup as came stock with the bike below. Fits: REARS on Honda CB750F (1977-78) Supersport Please Count your sprocket teeth and check your chain length before ordering to ensure this is correct for your bike
Steel Front Sprocket - 14 Tooth X 630
Steel Front Sprocket - 14 Tooth - Replaces OEM # 23801-410-000 For 630 Chain Setup as came stock with the bike below. Fits: FRONT on Honda CB750F (1977-78) Supersport Please Count your sprocket teeth and check your chain length before ordering to ensure this is correct for your bike
Oil Pressure Gauge Assembly ~ Black Face Plate
Oil Pressure Gauge Assembly. Includes a silver colored liquid filled gauge with a black face plate, (44mm) diameter, 0 to 100 PSI. Billet aluminum oil galley adapter, o-ring and a chrome 90° fitting included. Easily installs on the oil gally port above the points cover in minutes!
Oil Pressure Gauge Assembly ~ White Face Plate
Oil Pressure Gauge Assembly. Includes a silver colored liquid filled gauge with a white face plate, (44mm) diameter, 0 to 100 PSI. Billet aluminum oil galley adapter, o-ring and a chrome 90° fitting included. Easily installs on the oil gally port above the points cover in minutes!
Oil Pressure Gauge Assembly ~ Carbon Face Plate
Oil Pressure Gauge Assembly. Includes a silver colored liquid filled gauge with a carbon looking face plate, (44mm) diameter, 0 to 100 PSI. Billet aluminum oil galley adapter, o-ring and a chrome 90° fitting included. Easily installs on the oil gally port above the points cover in minutes!
Oil Pressure Gauge Assembly ~ Metal Machined Face Plate
Oil Pressure Gauge Assembly. Includes a silver colored liquid filled gauge with a metal machined design looking face plate, (44mm) diameter, 0 to 100 PSI. Billet aluminum oil galley adapter, o-ring and a chrome 90° fitting included. Easily installs on the oil gally port above the points cover in minutes!
Starter Solenoid Relay
Starter Solenoid Relay OEM Ref # 35850-375-000 / 35850-286-027
Rectifier/Regulator ~ Lithium Ion Battery Compatible
Rick's Electric Brand Lithium Ion Battery Compatible Rectifier-Regulator. Designed with a lower voltage set point to work with lithium ion batteries only. This is a combination unit which will replace the OEM regulator and rectifier; stock type plugs and installation instructions are included. Dimensions 70mm Length, 94mm Width, 27mm Height, Hole Distance 80mm Center to Center. Note: May require a custom mounting job. High quality Part. This is Not for use with standard lead acid batteries. The voltage set point is 14V +/- .2. Please ensure this set point is correct for your battery before attempting installation.
Starter Brush Set
Starter Brush Set/2 1Pc Insulated Leads 1Pc Non-Insulated Leads 12mm x 14mm x 6mm For Misuba 2 Brush Starter. OEM Ref # 31201-292-158 / 31201-MG9-004
Starter Clutch Diode
Starter Clutch Diode OEM Ref # 31700-124-003 / 31700-166-008
Starter Motor
Rick's Electrics Starter Motor, Replaces OEM# 31200-300-030 This starter motor features an upgraded 4-Brush permanent magnet design & comes with the battery cable.
Rectifier/Regulator
Rick's Electric Brand OEM Style Honda Rectifier-Regulator: This is a combination unit which will replace the OEM regulator and rectifier; stock type plugs and installation instructions are included. Dimensions 68mm Length, 94mm Width, 26mm Height, Hole Distance 80.0mm Center to Center. High quality Part. Note: May require a custom mounting job. Works great if attached with one bolt and nut where the safety starter switch was originally located (can bypass that switch).
Premium Stock Type Stator
Premium Made in the USA ~ Rick's Electrics ~ Stock Style Stator, Replaces OEM # 31102-300-045 / 31102-300-035 / 31102-393-025 / 31102-393-005 / 31102-393-015.
Wire Harness
Main Wire Harness Loom - OEM Ref. # 32100-410-010