Honda ► CB750K ►
-
Here’s our hand-picked list of electrical parts for your Honda CB750K with universal parts included►
- Honda
Tail Light Assembly
Tail Light Assembly. Includes Brake Light Lens, Back Plate, Screws, Gasket, Wires, Connector and Dual Filament Bulb. Replaces OEM # 33700-292-671 / 33700-235-673 / 33701-300-671 / 33701-307-670 Two Bolt Back Mounting Bolt Pattern (Approx 96mm Center to Center), 2 Wires, Ready to Mount to your Bike!
Signal Lamp Lens w Gasket & Screws - Red
Red Front/Rear Turn Signal Lamp Lens with Gasket and 2 Screws. OEM Ref # 33402-268-671
Turn Signal Stem
Front Signal Lamp Stay - Chrome. Body Length 65mm, Thread 25mm, Total Length 90mm. Note: We sell these in Various Lengths, Confirm this is the Size you would Like Before Purchase
Tail Light Lens Gasket
Tail Light Lens Gasket - Replaces OEM# 33709-077-671
Front/Rear Signal Lamp ~ 1 Wire Type
Signal Lamp - Amber - 12v - 1 wire for Front or Rear - Replaces OEM# 33600-447-000 / 33600-447-P00. Please double check you require the 1 wire type before purchasing Stem *Our Part Number 11-2167*
Tail Light Lens
Red Tail Light Lens with Amber Side Reflectors. OEM Ref # 33702-077-671
Stock Type Front Reflector Rubber Base
Stock Type Front Reflector Rubber Base - Replaces OEM# 33743-341-670
Fender Eliminator Taillight
Fender Eliminator 12 Volt Taillight with 2 Wires. This fits to our fender eliminator (#73-1144) and looks great! Note: Photo shows Taillight Mounted to Fender Eliminator #73-1144 for Reference Only, it is not included with this item. Please purchase it separate
Stop Light Switch
Rear Stop Light Switch OEM Ref # 35350-292-003 / 35350-KJ9-405
Starter / Horn Button
Starter / Horn Button
Ignition Switch Assembly
Ignition Switch Assembly With round wire harness to switch connector. Round plug 6 Hole, 4 Wire Type. OEM Ref # 35100-303-007 / 35100-292-003 / 35100-292-013 Note: We offer an ignition switch nut tool on our site to easily loosen or tighten the ignition switch nut without causing damage to the switch
Ignition Switch Assembly
Ignition Switch Assembly Square End Plug Type - 4 Prong OEM Ref # 35100-341-700 / 35100-374-007 / 35100-369-740 Note: We offer an ignition switch nut tool to easily loosen or tighten the ignition switch nut without causing damage to the switch.
Bar Switch Assembly ~ Right (Brake) Side
Bar Switch Assembly ~ Right (Brake) Side - Black. Replaces OEM # 35300-300-672 Note: Wiring to be run Inside the handlebar. This is a single throttle cable configuration type assembly.
Bar Switch Assembly ~ Left (Clutch) Side
Bar Switch Assembly ~ Left (Clutch) Side - Black. Replaces OEM # 35250-300-033
Alternator Cover Gasket
Alternator Cover Gasket (Dyno Cover) - OEM Ref. # 11397-300-303
Contact Point
Contact Point - Right Side OEM Ref # 30203-300-005 / 30203-300-154
Contact Point
Contact Point - Left Side OEM Ref # 30204-300-005 / 30204-300-154
Spark Advancer Assembly
Spark Advancer Assembly, Replaces OEM# 30220-300-154
Spark Advance Shaft
Spark Advance Shaft with O-Ring, Replaces OEM# 30231-300-010 / 91301-300-000 The shaft has been nitrate coated to guard against corrosion and it comes with an upgraded Viton O-Ring.
Ignition Coil
Ignition Coil Stock type for contact point ignitions. 100mm center to center mounting points. OEM Ref # 30501-300-03 / 30501-300-013 / 30502-300-003 / 30502-300-013
Negative (-) Battery Cable
Negative (-) Battery Cable (Ground Cable). Replaces OEM # 32601-MG9-000
Positive (+) Battery Cable
Positive (+) Battery Cable with Rubber End Covers. Replaces OEM # 32401-300-010
Rectifier/Regulator ~ Lithium Ion Battery Compatible
Rick's Electric Brand Lithium Ion Battery Compatible Rectifier-Regulator. Designed with a lower voltage set point to work with lithium ion batteries only. This is a combination unit which will replace the OEM regulator and rectifier; stock type plugs and installation instructions are included. Dimensions 70mm Length, 94mm Width, 27mm Height, Hole Distance 80mm Center to Center. Note: May require a custom mounting job. High quality Part. This is Not for use with standard lead acid batteries. The voltage set point is 14V +/- .2. Please ensure this set point is correct for your battery before attempting installation.
Starter Brush Set
Starter Brush Set/2 1Pc Insulated Leads 1Pc Non-Insulated Leads 12mm x 14mm x 6mm For Misuba 2 Brush Starter. OEM Ref # 31201-292-158 / 31201-MG9-004
Rectifier Regulator
Universal Type Rectifier Regulator 8 Wires - No End Terminals