Honda ► CB750K ►
-
Here’s our hand-picked list of electrical parts for your Honda CB750K with universal parts included►
- Honda
Starter Motor
Rick's Electrics Starter Motor, Replaces OEM# 31200-300-030 This starter motor features an upgraded 4-Brush permanent magnet design & comes with the battery cable.
Rectifier/Regulator
Rick's Electric Brand OEM Style Honda Rectifier-Regulator: This is a combination unit which will replace the OEM regulator and rectifier; stock type plugs and installation instructions are included. Dimensions 68mm Length, 94mm Width, 26mm Height, Hole Distance 80.0mm Center to Center. High quality Part. Note: May require a custom mounting job. Works great if attached with one bolt and nut where the safety starter switch was originally located (can bypass that switch).
Premium Stock Type Stator
Premium Made in the USA ~ Rick's Electrics ~ Stock Style Stator, Replaces OEM # 31102-300-045 / 31102-300-035 / 31102-393-025 / 31102-393-005 / 31102-393-015.
Oil Pressure Switch Wire Assembly
Oil Pressure Switch Wire Assembly. Includes the Wire and Rubber Cover. Replaces OEM # 31270-300-154 / 31270-300-005
Alternator Stator Wire Harness
Alternator Stator Wire Harness, This Harness has the Same 7 Wire Plug as the OEM part and Hooks up Without Alterations. Replaces OEM # 31110-300-154
Rear Brake Light Stop Switch Spring
Rear Brake Light Stop Switch Spring. This is the Spring that Attaches to the Rear Stop Light Switch. Replaces OEM # 35357-300-000
Headlight Adjusting Screw & Spring Set
Headlight Adjusting Screw & Spring Set. Each Set Includes One Screw and One Spring. Replaces OEM # 33103-346-670 (Screw) and OEM # 33107-300-003 (Spring)
Starter Motor Bolt (Set/2)
Starter Motor Flange Bolt Set/2. Replaces OEM # 95700-06056-00
Hydraulic Brake Light Switch
Hydraulic Brake Light Switch - OEM Ref # 35350-300-006 / 35350-300-016 / 341-83980-30-00 10mm x M1.25 thread
Tail Light Mounting Hardware Set
Tail Light Mounting Hardware Set (8 Pc. Set). This set is used to mount your tail Light to the tail Light bracket. Each set Includes 2X Rubber Grommets, 2X Collars, 2X Bolts and 2X Washers.
Ignition Switch Nut Tool
Ignition Switch Nut Tool, used to loosen and tighten the igntion switch nut properly without causing any damage to the switch.
Front Signal Lamp Stay Nut & Washer Set
Front Signal Lamp Stay Nut & Washer Set. These are the Nuts and Washers that thread into the Front Turn Signal Stays. Set includes 2 Nuts and 2 Washers, Enough for both Front Signal Stays.
Lens Screw
Tail Light Lens Screws, Pack of 10. Replaces OEM # 93500-04050-4J ISO Std. Pitch - Steel Plated Size: 4 x 50mm
NGK Spark Plug
NGK D8EA Spark Plug - Standard Original CB750 Spark Plug 4 required per CB750, Order the quantity you require.
NGK Iridium Spark Plug
NGK DR8EIX Iridium Spark Plug Cheapest Horsepower You Can Buy for your CB! Adds a Solid 1-2 HP to your Bike! 4 required per bike, Order the Quantity you require.
Stock Type Ignition Coil Set/2 With Brackets
Stock Type Ignition Coil Set/2 With Brackets. Replaces OEM# 30500-300-013 Dual Coil Assembly Pre-Mounted on their Brackets Just Like the Stock Type. Plug and Play Easy Install. Primary 4.3 Ohm, Secondary 15,000k Ohms.
Tail Light Cable Set
Tail Light/Brake Light Cable Set of 3. Replaces OEM # 33711-323-000 (Tail Light Sub Cable), OEM # 33712-300-003 (Taillight Ground Cable) and OEM # 33713-323-000 (Stop Light Sub Cable).
Starter Motor Terminal Rubber Boot
Starter Motor Terminal (Cover) Rubber Boot. Replaces OEM # 32411-230-000
Headlight Plug ~ OEM Style
Headlight Plug ~ OEM Style, Replaces OEM # 33130-300-003
Oil Pressure Switch
Oil Pressure Switch, Replaces OEM # 37240-P13-013
Turn Signal Pinch Bolt Set
Turn Signal Pinch Bolt Set. Includes 2X Chrome Bolts, 2X Hex Nuts and 4X Flat Washers. This set is used to clamp the turn signal onto the stem. Some models originally had a 25mm long bolt but these will interchange. This set includes hardware for 2 turn signals. If you need enough for all 4 signals please purchase 2 sets.