Honda ► CB750K ►
-
Here’s our hand-picked list of electrical parts for your Honda CB750K with universal parts included►
- Honda
Cast Aluminum Finned Starter Motor Cover
Cast Aluminum Finned Starter Motor Cover, Made in the USA. Replaces OEM # 31280-300-000 This is a new cover designed and produced like the ones from the 70's that aren't made anymore. This cover is delivered in as-cast condition. As such, Sandblasting, painting, or powder coating will be required if you want a look other then the cast aluminum look. As delivered it is a close match for an original patina engine. Note: Gasket and Hardware Not Included with Cover
Turn Signal Relay
Turn Signal (Flasher) Relay. OEM Style Replacement 12V/23W, 3 Prong, Comes with Rubber Mount Attached. Replaces OEM # 38301-415-671 Not for Use with Custom LED Lights
Front Signal Lamp Stay
Front Signal Lamp Stay - Chrome. Body Length 40mm, Thread 30mm, Total Length 70mm. Note: We sell these in Various Lengths, Confirm this is the Size you would Like Before Purchase
Rear Turn Signal Grounds (Pk/2)
Rear Turn Signal Ground Cables (Pk/2), Replaces OEM # 33620-300-000 These Cables are Needed in order to Ground the Rear Turn Signals, Overall Length 550mm.
Ignition Switch Mounting Bracket & Hardware Set
Ignition Switch Mounting Bracket & Hardware Set. Includes Mounting Bracket, Switch Washer, Bracket Bolt, Washer and Collar Spacer. Replaces Mounting Bracket OEM # 50375-300-000B
Horn Hardware Set
Horn Hardware Set, Includes 2 Bolts and 2 Washers. Replaces OEM # 92101-06016-0A X2 (Bolt) and OEM # 94111-06000 X2 (Washer).
Headlight Bucket Case
Black Headlight Bucket / Case, Stock Design - Replaces OEM # 61301-300-020B
Fuse Box Assembly *Damaged Tabs*
*Damaged Tabs* Fuse Box Assembly Complete with 15Amp Fuses, Replaces OEM# 38200-MF9-405. This Fuse Box Typically has 4 Sets of Attachment Tabs on the back of the assembly used to fasten to the bike. However, several had tabs broken during transit so our loss is your gain! This unit has absolutely nothing wrong with the electrics. The unit your purchasing has damage to some or all of the tabs used to fasten the unit to your bike. Due to where it is attached all tabs should not be needed for installation. You may or may not need to find a solution such as glue/tape etc. to install but it should not pose any problems. As there is a cover over this unit if you use a little duct tape etc. nobody will ever know.
Fuse Box Assembly *Damaged Tabs*
*Damaged Tabs* Fuse Box Assembly Complete with 10Amp Fuses, Replaces OEM# 38200-425-005. This Fuse Box Typically has 4 Sets of Attachment Tabs on the back of the assembly used to fasten to the bike. However, several had tabs broken during transit so our loss is your gain! This unit has absolutely nothing wrong with the electrics. The unit your purchasing has damage to some or all of the tabs used to fasten the unit to your bike. Due to where it is attached all tabs should not be needed for installation. You may or may not need to find a solution such as glue/tape etc. to install but it should not pose any problems. As there is a cover over this unit if you use a little duct tape etc. nobody will ever know.
Rectifier/Regulator
Rectifier-Regulator: This is a combination unit which will replace the OEM regulator and rectifier. This has the OEM type ground wiring and Stock Type Plugs. Dimensions 80mm Length, 94mm Width, 27mm Height, Hole Distance 70.0mm Center to Center. Instructions not included.
Electronic Ignition System
Electronic Ignition System. Direct plug-in fitment. Increase RPM 100% tested before shipment, high reliability and high performance! This ignition can be used with your stock coils or any other coils 3 ohms or higher.
Pilot Indicator Light Cover
Pilot Indicator Light Cover, Replaces OEM# 37600-377-018 This includes the front and rear cover with fastening screws.
Stock Type Battery Band
Stock Type Battery Band, Replaces OEM# 95012-17001 Band Overall Size: 6.125" (155mm) Measuring from the inside of the brackets.
Front Reflector
Front Reflector, Replaces OEM# 33742-HB9-641 / 33741-413-003 / 33741-413-013 Amber Reflector with Black Plastic Ring. 2 Segments in the Reflector (Instead of 6 Like the OEM).
Stock Style Stator
Stock Style Stator, Replaces OEM # 31102-300-045 / 31102-300-035 / 31102-393-025 / 31102-393-005 / 31102-393-015. We had these hard to find stators re-manufactured to keep your CB on the road!
Headlight Stay / Headlight Reflector Bolt
Headlight Stay / Headlight Reflector Bolt, Replaces OEM# 90120-425-000. This is the bolt that the headlight reflectors / reflector base attach to, this bolt fastens through the headlight ears. Sold Each, 2 Used Per Bike
Headlight Reflector Rubber Base
Headlight Reflector Rubber Base, Replaces OEM# 33743-375-000 This is the rubber base that the headlight reflector attaches to. Sold Each, order the quantity you require
Headlight Stay / Headlight Reflector Bolt
Headlight Stay / Headlight Reflector Bolt, Replaces OEM# 90120-377-000 This is the bolt that the headlight reflectors / reflector base attach to, this bolt fastens to the headlight. Sold Each, 2 Used Per Bike
Headlight Reflector Rubber Base
Headlight Reflector Rubber Base, Replaces OEM# 33743-425-600 This is the rubber base that the headlight reflector attaches to. Sold Each, order the quantity you require
Horn ~ Similar to Stock Style
Horn with Chrome Cover - 12 Volt 3 Amp - 103 Decibel - This is Not identical to the stock type but has a somewhat similar design to the stock type on these bikes.
Custom Micro Push Button/Kill Switch
Custom Micro Push Button/Kill Switch. High quality chrome switch designed to clean up the appearance of your bike while allowing the use of a switch. Works great as a hidden start/kill or horn button. Includes a contoured washer which allows for installations on round surfaces such as handlebars or frames. Switch Size 14mm x 12mm with 2X 20" wires.
Ignition Coil ~ 5 Ohm
Dual Tower Performance High Output Ignition Coil 5.2 OHM Primary resistance ignition coil, 17K OHM Secondary Resistance. Can be used with all contact point ignitions and aftermarket electronic ignitions (non CDI) requiring a 5 OHM Coil. Fits most CB's, KZ/Z1 900/1000, KZ650 etc
Dynatek Performance High Output 3 Ohm Ignition Coil Set/2 With Plug Wires
Dynatek Performance Dual Output 3 Ohm Ignition Coil Set/2 with Dynatek Performance Spark Plug Wire Set, 7mm Black Silicone Copper Core. Includes Hardware and Instructions. Comes with a one year warranty through Dynatek. Wires are 4' Length (cut to your needed length). 2 wires in this set which can be cut into 4. All wires are supplied with finished spark plug boot ends and loose coil terminals to allow the final length to be determined by the user. Wires feature a solid copper core for use on older vehicles where electrical interference is not an issue. High quality made in the USA. These high tech, top quality coils are made in the USA and are designed for maximum performance. They produce spark voltages in excess of 30,000 volts and spark energies second to none. Dyna Coils work with point ignitions, aftermarket electronic ignitions and factory electronic ignitions. Before selecting a coil check the coil primary resistance requirements as specified by the manufacturer of the ignition being used before purchasing. When choosing the right coil for your bike, never select a coil with a lower resistance than your ignition system.
Dynatek Charge Monitor
Dynatek Charge Monitor. Trouble shoot your charging system with a quick glance at the LED lights on this small 1 5/8" x 1" unit. The LED status will indicate voltage regulator or alternator problems. The Dyna Charge Monitor is a valuable addition to vehicles with a battery ignition and a charge system as found on nearly all stock vehicles. The Charge Monitor allows easy determination of the operational state of the charging system with a quick glance at the indicator LED's. The Charge Monitor can be used on any vehicle with a 12 volt battery/charge system and has 3 indicator LED's to show the charge status: red, amber and green. When the right most red LED is on the battery is being overcharged due to a faulty voltage regulator. When the green LED is on, the battery is being charged at a normal voltage. When the left most red LED is on, the battery voltage is getting very low and the charge circuit or battery is failing. High quality made in the USA. Comes with a one year warranty through the manufacturer.
Performance Tool Spark Plug Crimper Tool
Performance Tool Spark Plug Crimp Tool. Perfect crimping tool for any spark plug wires. Incorporates wire cutter, terminal crimper tool and stripper in one handy tool. Black anodized finish with insulated hand grips. Crimp slot on the end of the tool secures most ignition terminals including "W" type, right angle and "High Tower" terminals. Crimps 7mm to 8.5mm ignition wire. Works with 10 to 22 gauge solderless terminals. High quality made in the USA. Comes with a lifetime warranty through the manufacturer!