Honda ► CB750K ►
-
Here’s our hand-picked list of electrical parts for your Honda CB750K with universal parts included that match “screws nuts bolts tools”►
- Honda
Ignition Switch Nut Tool
Ignition Switch Nut Tool, used to loosen and tighten the igntion switch nut properly without causing any damage to the switch.
Ignition Switch Assembly
Ignition Switch Assembly Square End Plug Type - 4 Prong OEM Ref # 35100-341-700 / 35100-374-007 / 35100-369-740 Note: We offer an ignition switch nut tool to easily loosen or tighten the ignition switch nut without causing damage to the switch.
Lens Screw
Tail Light Lens Screws, Pack of 10 Screws. Replaces OEM # 93500-04055-4J ISO Std. Pitch - Steel Plated Size: 4 x 55mm
Ignition Coil Holder Clamp
Ignition Coil Holder Clamp with Bolt, Washer and Nut. This is the clamp that holds the ignition coil in place. Replaces OEM # 30151-300-000 / 30152-300-000
Neutral Switch Screw
Neutral Switch Screw, This is the small Screw that threads into the Neutral Switch. Replaces OEM # 35752-300-020
Points Cover Screws
Points Cover Screws (Set of 2). Fits: ALL 1969-1978 Honda CB750 Points Covers and Our Points Cover (Part #13-0000).
Headlight Adjusting Screw & Spring Set
Headlight Adjusting Screw & Spring Set. Each Set Includes One Screw and One Spring. Replaces OEM # 33103-346-670 (Screw) and OEM # 33107-300-003 (Spring)
Turn Signal Lamp Lens Screw Set
Turn Signal Lamp Lens Screw Set/2, Replaces OEM # 93500-04025-0A ALSO Fits our Signal Lens #11-2195 and Signals #11-2114 and #11-2149
Starter Motor Bolt (Set/2)
Starter Motor Flange Bolt Set/2. Replaces OEM # 95700-06056-00
Rectifier/Regulator
Rick's Electric Brand OEM Style Honda Rectifier-Regulator: This is a combination unit which will replace the OEM regulator and rectifier; stock type plugs and installation instructions are included. Dimensions 68mm Length, 94mm Width, 26mm Height, Hole Distance 80.0mm Center to Center. High quality Part. Note: May require a custom mounting job. Works great if attached with one bolt and nut where the safety starter switch was originally located (can bypass that switch).
Stock Type Reflector
Stock Type Screw on Reflector, 6mm thread. Replaces OEM # 33741-340-670
Horn Hardware Set
Horn Hardware Set, Includes 2 Bolts and 2 Washers. Replaces OEM # 92101-06016-0A X2 (Bolt) and OEM # 94111-06000 X2 (Washer).
Ignition Switch Mounting Bracket & Hardware Set
Ignition Switch Mounting Bracket & Hardware Set. Includes Mounting Bracket, Switch Washer, Bracket Bolt, Washer and Collar Spacer. Replaces Mounting Bracket OEM # 50375-300-000B
Tail Light Mounting Hardware Set
Tail Light Mounting Hardware Set. This Set is Used to Mount the Tail Light Bracket. This 12pc Set Includes 4pc Tail Light Setting Bolts, 4pc Tail Light Setting Washer and 4pc Rubber Fender Cushion.
Custom Black Horn with Bracket ~ Joker Machine
Joker Machine Brand ~ Small Custom Black Horn with CNC Machined Bracket and 2 Gold Mounting Screws. This horn relocates to the center-line of the frame instead of the stock horn's offset position. This custom small horn gives your bike a racy billet look and enables better clearance for steering damper installations. High quality made in the U.S.A.
Battery Box Rubber Set
Battery Box Rubber Set. Includes Battery Rubber X1, Battery Box Collar X1, Bolt X1 and Washer X1. This set fastens into the top section of the Battery Box. Fits: Honda CB750K (1969-76) - 4 Sets Used Per Bike, CB750K (1977-78) - 3 Sets Used Per Bike, CB750F (1975-76) Supersport - 4 Sets Used Per Bike, CB750F (1977-78) Supersport - 3 Sets Used Per Bike, CB750A (1976-78) Hondamatic - 2 Sets Used Per Bike Note: Order the Quantity of Sets you Require
Performance Tool Spark Plug Crimper Tool
Performance Tool Spark Plug Crimp Tool. Perfect crimping tool for any spark plug wires. Incorporates wire cutter, terminal crimper tool and stripper in one handy tool. Black anodized finish with insulated hand grips. Crimp slot on the end of the tool secures most ignition terminals including "W" type, right angle and "High Tower" terminals. Crimps 7mm to 8.5mm ignition wire. Works with 10 to 22 gauge solderless terminals. High quality made in the USA. Comes with a lifetime warranty through the manufacturer!
Terminal Crimping Tool
Metric Terminal Crimper Tool. Includes sizes 14-16, 14-18, 18-20, 20-24 and 22-24. Professionally Crimps like factory originals. This tool can be used with flag type terminals.
Spark Plug Gapping Tool
Circular Spark plug gap tool. Marked in thousandths of an inch and millimeters.
Heavy Duty Terminal Crimper Tool
Heavy Duty Metric Terminal Crimper Tool, fastens metric terminals to wires. Includes sizes 10-12, 14-16 and 18-22. Professionally Crimps like factory originals.
Turn Signal Light Mount Bracket Holder Set
Black Metal Fork Ear Clamp/Turn Signal Light Mount Bracket Holder Set/2 with Screws, Washers and Nuts. Fits 30-45mm Front Forks
Turn Signal Light Mount Bracket Holder Set
Chrome Metal Fork Ear Clamp/Turn Signal Light Mount Bracket Holder Set/2 with Screws, Washers and Nuts. Fits 30-45mm Front Forks
Headlight Shell and Rim
Custom 7" Satin Black Side Mount Headlight Shell with Chrome Trim Ring. Designed for 7" sealed type headlights. Includes a 3 wire plug that works with sealed beam or H4 bulbs as well as the clip/screw and wire clips. Side mounting holes are threaded to use 5/16-24 bolts (bolts not included). Outer side mounting points are 7" apart. 3" Mounting depth from mounting holes to the back of the bucket. Sealed beam Headlight sold separately #09-0008 (Below), or the upgraded halogen beam #09-0051
Battery Jumper Cables
Battery Jumper Cables. 6 Feet in Length, These cables feature 10-gauge battery cables and insulated color-coded terminal clamps for safe and secure handling. The smaller clamp size easily fits motorcycle's, ATV's, UTV's, snowmobile's, watercraft's, etc.
Alternator/Battery Checker
Alternator/Battery Checker LED Voltage, Battery & Alternator Multi-Checker. For All 12 Volt Systems
Electrical Circuit Tester
Electric Circuit Tester - Checks all motorcycle primary electrical and computer circuits for power. Plastic handle lights up if circuit is good. Icepick type probe and 48" cable with insulated alligator clips.
Front Signal Lamp Stay ~ Short Type
Front Signal Lamp Stay with Nut and Washer ~ Short Type - Chrome. These are M10 x 1.50 with nut - Ensure your bike requires this thread size before purchasing. Body Length 26mm, Thread 21mm, Total Length 47mm.
LED Turn Signal Set/2
Custom LED Turn Signal Set/2. 3.5" Long Turn Signals with 10" Long Wires, DC 12 Volt. Will screw on to 10mm Screw holes. 2 Wire (Signal and Ground). These Require an LED relay to work. We sell these #12-0130
Custom LED Turn Signal Set/2
Custom LED Amber Lens Turn Signal Set/2. 2.5" Long Turn Signals with 10.5" Long Wires, DC 12 Volt. Will screw on to 8mm Screw holes. 2 Wire (Signal and Ground). These Require an LED relay to work. We sell these #12-0130
Horn with Chrome Grill
Horn with Chrome Snap on/off Grill Cover. 12 Volt, 2.5 Amp, 95mm Diameter. Two wire hookup, with spade terminals. Tone adjustment screw on backside.
Custom Chrome Dual Beam Headlights
Custom Chrome 4" Dual Beam Headlight Set. Complete universal side mount dual hi/low beam head light assembly. The two high quality glass sealed beam style lights have H4 60/55 watt bulbs along with pilot running lights in each light. Assembled and pre-wired harness to simply plug into your existing H4 plug. Side mounting bolts hole are threaded for M8 x 1.25 bolts. Total outer width at side mounting bolts in 8 1/2" wide. Center of mounting bolts to rear of the light bucket is 2 5/8" in depth. From the front of the trim ring to the rear of the bucket is about 4 1/2" in depth.
Custom Matte Black Dual Beam Headlights
Custom Matte Black 4" Dual Beam Headlight Set. Complete universal side mount dual hi/low beam head light assembly. The two high quality glass sealed beam style lights have H4 60/55 watt bulbs along with pilot running lights in each light. Assembled and pre-wired harness to simply plug into your existing H4 plug. Side mounting bolts hole are threaded for M8 x 1.25 bolts. Total outer width at side mounting bolts in 8 1/2" wide. Center of mounting bolts to rear of the light bucket is 2 5/8" in depth. From the front of the trim ring to the rear of the bucket is about 4 1/2" in depth.
Universal Ignition Switch Bracket
Chrome Universal Ignition Switch Bracket. Switch hole is 22.5mm, bolt hole is 9.5mm, overall length is 75mm. Fits to our #12-0058 Sold Separate
Hydraulic Brake Light Switch
Hydraulic Brake Light Switch Banjo Bolt Type - 10mm x M1.25 Can Be Used Front/Rear At Single Banjo Brake Line Fitting Correct Thread For Most Honda/Kawasaki/Yamaha Stock Fittings
Chrome Mini Retro Hooded Tail Light
Chrome Mini Retro Hooded Tail Light with Mounting Hardware. Features a pivoting mounting base bracket. Includes running light, brake light and tag light functions. Uses a standard 21/5 watt 1157 bulb. Wire lead is about 10" long. Housing is 2 1/8" round x 3 3/8" long over all. Stands about 3 1/4" tall from base of mounting bracket. Mounting base is 2" long x 3/4" wide. Mounting bolt holes are 1/4" holes x 1 1/4" center to center.
Satin Black Mini Retro Hooded Tail Light
Satin Black Mini Retro Hooded Tail Light with Mounting Hardware. Features a pivoting mounting base bracket. Includes running light, brake light and tag light functions. Uses a standard 21/5 watt 1157 bulb. Wire lead is about 10" long. Housing is 2 1/8" round x 3 3/8" long over all. Stands about 3 1/4" tall from base of mounting bracket. Mounting base is 2" long x 3/4" wide. Mounting bolt holes are 1/4" holes x 1 1/4" center to center.
Vintage Round Chrome Taillight
Vintage All Steel Round Chrome Taillight with plate bracket, bolts and washers. 1 5/8" Round plastic lens (with a clear bottom to light up your plates), 12 volt double filament bulb. Works as a running and brake light. Base mounting plate measures 2" top to bottom and 2 1/2" wide. Mounting base 6mm holes are 1 1/4" wide x 7/8" top to bottom, tag mounting plate measures 6 1/2" wide, tag mounting holes 4 1/2" centered.