Honda ► CB750K ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB750K that match “honda sl125”►
- Honda
Rear Wheel Bearing
Rear Wheel Bearing with 2 Synthetic Shields - 6305-2RS Size Replaces OEM# 96140-63050-10 High Quality Made in Japan
Center Stand Spring Plate
Center Stand Spring Plate, This is the Plate the Center Stand Spring Attaches to. Replaces OEM # 50523-425-000
Footrest Rubbers
Footrest Rubbers (Set/2) - OEM Ref # 50661-425-670
Front Reflector
Front Reflector, Replaces OEM# 33742-HB9-641 / 33741-413-003 / 33741-413-013 Amber Reflector with Black Plastic Ring. 2 Segments in the Reflector (Instead of 6 Like the OEM).
Front Wheel Bearing Retainer Ring Tool
Front Wheel Bearing Retainer Ring Tool. High quality tool for removing and fitting the front wheel bearing retainer ring with 1/2 inch socket bar wrench tool hole. The perfect tool for easier removal and fitting without damaging the special retainer ring.
Brake Caliper Rebuild Kit
Brake Caliper Rebuild Kit Front - Dual
Ultimate Performance Main Jet Kit
Ultimate Performance Main Jet Kit. Kit includes a total of 44 Main Jets for Keihin Carbs. Use this jet kit to unleash the extra power you should have from your aftermarket exhaust, flee flowing air filters or any engine mods you have made. Kit includes Main Jets #100 (X4), #102 (X4), #105 (X4), #108 (X4), #110 (X4), #112 (X4), #115 (X4), #118 (X4), #120 (X4), #122 (X4) and #125 (X4)
White - 750 Four Logo Hat
White - 750 Four Logo Hat. Adjustable Bronze Clasp Back
Black - 750 Four Logo Hat
Black - 750 Four Logo Hat. Adjustable Bronze Clasp Back
Chrome Brake Lever
Chrome Brake Lever - OEM Ref # 53175-MA5-671 / 53175-MA6-016 / 53175-MA6-006 / 53175-MB0-006
Carb Float
Carb Float with Pin, Replaces OEM # 16013-413-851 Note: Order the Quantity of Floats you Require
Air Cut Off Valve With Cover
Carb Air Cut Off Valve with Cover - OEM # 16048-429-771 (Diaphragm), 16048-425-771 (Spring + 1 O-Ring), 16048-429-771 (Cover).
Side Stand Rubber
Side Stand Rubber Cushion. Replaces OEM # 50548-356-700
Float Needle
Float Needle High Quality - Made In Japan OEM Ref # 16155-413-751 / 16155-397-971
Air Screw Needle O-Ring
Air Screw Needle O-Ring. 2.8mm x 1.2mm. Note: sold each, order the quantity you require
Neutral Switch Assembly
Neutral Switch Assembly OEM Ref # 35600-425-023
Replacement Coil Caps & Seals
Replacement Coil tower caps & seals. Fits stock points ignition coils OR our part number 17-6803.
Sub-Wire Harness "A"
Sub-Wire Harness "A", Replaces OEM # 32103-438-660 Plugs into the main wire harness and connects to the ignition coils. This item is not included with our main wire harness's. Please order this item if you require this sub-wire harness "A".
Shock Absorber Nut
Shock Absorber Nut, Used when Installing Shocks. Replaces OEM # 90309-315-000 Note: Nuts sold Each, order the quantity you require
Clutch Tab Washer
Clutch Tab Washer, 16mm Size, Replaces OEM # 90431-292-000
Brake Pedal Return Spring
Brake Pedal Return Spring. This is the Spring Used where the Brake Pedal Attaches to the Brake Spindel. Replaces OEM # 46514-425-010
High Performance Kibblewhite Intake/Exhaust Valve Guide
High Performance Kibblewhite Intake or Exhaust Valve Guide (Standard Size). Made in the USA by Kibblewhite who have been making High Quality Performance parts for 75+ years. Kibblewhite uses the copper based C63000 nickel-aluminum bronze as a material to make these bronze valve guides because of its ideal characteristics for the application. The 5% nickel content provides superior resistance to wear, and the approximately 80 percent copper content delivers outstanding heat conductivity. Kibblewhite guide profiles are designed to have minimal effect on the airstream while maintaining critical cross sectional thickness in high temperature areas, which promotes high performance and endurance. Sold Each, Order the Quantity you Require
Exhaust Stud Set
Exhaust Stud Set. Includes 8 Exhaust Studs and 8 Flange Nuts.
Sidecover Damper Rubber B
Rubber Sidecover Damper B, Replaces OEM # 83551-300-000
Carb Air Box Rubber Boot Set/4
Carburetor to Air Box Rubber Boot Set of 4. Replace your Old Worn, Cracked or Dried out Rubber Boots with a Brand New Set! Replaces OEM # 17253-425-000 X2 and 17254-425-000 X2. NOTE-If you require band clamps, these rubber boots require our 58-60mm diameter band clamps part #15-0690 X4 or gear clamps #15-0670 X4.