Honda ► CB750K ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB750K►
- Honda
Alternator Stator
Alternator Stator OEM Ref # 31120-425-852 / 31120-425-871 / 31120-MG1-000 / 31120-MG1-005 / 31120-MG5-005 / 31120-461-415 / 31120-461-405 / 31120-461-671 / 31120-461-005 / 31120-426-005 / 31120-426-832
Rectifier Regulator
Rectifier Regulator 8 Wire (1 Four Prong Plug With 3 Wires, 1 Six Prong Plug With 5 Wires) OEM Ref # 31600-461-771 / 31600-MA6-000 / 08154-4610012 / 31600-425-008 / 31600-MA6-910
Rectifier Regulator
Universal Type Rectifier Regulator 8 Wires - No End Terminals
Starter Clutch Diode
Starter Clutch Diode OEM Ref # 31700-124-003 / 31700-166-008
Starter Motor
Rick's Electrics Starter Motor, Replaces OEM# 31200-300-030 This starter motor features an upgraded 4-Brush permanent magnet design & comes with the battery cable.
Rotor Brush Plate Holder
Rotor Brush Plate Holder for Alternators, Replaces OEM# 31126-422-015 / 31126-422-005.
Rectifier/Regulator
Rick's Electric Brand OEM Style Honda Rectifier-Regulator: This is a combination unit which will replace the OEM regulator and rectifier; stock type plugs and installation instructions are included. Dimensions 68mm Length, 94mm Width, 26mm Height, Hole Distance 80.0mm Center to Center. High quality Part. Note: May require a custom mounting job. Works great if attached with one bolt and nut where the safety starter switch was originally located (can bypass that switch).
Premium Stock Type Stator
Premium Made in the USA ~ Rick's Electrics ~ Stock Style Stator, Replaces OEM # 31102-300-045 / 31102-300-035 / 31102-393-025 / 31102-393-005 / 31102-393-015.
Honda CB Charging Rotor
Honda CB Charging Rotor, Replaces OEM # 31110-426-832 This rotor is a high quality OEM style replacement for Honda field coil rotors. The field coil is wound to stock specifications. This rotor is an easy installation and provides years of trouble free reliability from your Honda engine. Easy bolt-in installation just like the stock rotor.
Sub-Wire Harness "A"
Sub-Wire Harness "A", Replaces OEM # 32103-438-660 Plugs into the main wire harness and connects to the ignition coils. This item is not included with our main wire harness's. Please order this item if you require this sub-wire harness "A".
Horn Sub Harness "A"
Horn Sub Harness "A", This is the Harness that Attaches to the Horn. Replaces OEM # 32101-438-000
Oil Pressure Switch Wire Assembly
Oil Pressure Switch Wire Assembly. Includes the Wire and Rubber Cover. Replaces OEM # 31270-300-154 / 31270-300-005
Alternator Stator Wire Harness
Alternator Stator Wire Harness, This Harness has the Same 7 Wire Plug as the OEM part and Hooks up Without Alterations. Replaces OEM # 31110-300-154
Rectifier/Regulator ~ Lithium Ion Battery Compatible
Rick's Electric Brand Lithium Ion Battery Compatible Rectifier-Regulator. Designed with a lower voltage set point to work with lithium ion batteries only. This is a combination unit which will replace the OEM regulator and rectifier; plug and play easy install plugs. Replaces OEM# 31600-MA6-910, 316-MA6-000, 311600-MA7-008, 31600-425-008, 31600-461-771, 311600-MG5-000. This is Not for use with standard lead acid batteries. The voltage set point is 14V +/- .2. Please ensure this set point is correct for your battery before attempting installation.
Rick's Electrics Brand ~ Ignition Coil
Rick's Electrics Brand Replacement Ignition Coil - OEM Ref# 21121-1310, 21121-1039 , 21121-1309,21121-1038 , 21121-1041 , 21121-1036 , 21121-1035 , 21121-1110 , 21121-1111 , 30510-MA6-013 , 30510-MA6-003 , 30510-MR7-003 , 30500-422-013 , 30500-422-003 , 30505-MB9-003. Note: 2 Coils Used per Bike, Order the Quantity you Require Note: Comes with Wires Attached
Handlebar - Stock Type ~ CB750 1969-71
Stock Type Handlebar for the CB750K (1969-71) - Chrome. Drilled for wires like the OEM type. Bar Diameter - 7/8" - 22mm, Length - 32" - 812mm, Pull Back - 5 3/8" - 136mm, Inner Rise - 5 1/4" - 133mm, End Rise - 6 7/8" - 175mm, Center Width - 6 1/2" - 165mm, Base Width - 9 1/2" - 241mm, Knurl Width - 4 1/2" - 114mm, Control Length - 9" - 228mm, Drilled - YES Replaces OEM # 53100-300-000 Note: These Are Drilled For Wires
Handlebar - Stock Type ~ CB750 1972
Stock Type Handlebar for the CB750K (1972) - Chrome. Drilled for wires like the OEM type. Bar Diameter - 7/8" - 22mm, Length - 28 1/2" - 648mm, Pull Back - 4" - 101mm, Inner Rise - 3 1/8" - 79mm, End Rise - 3" - 76mm, Center Width - 5 1/2" - 140mm, Base Width - 7 1/2" - 190mm, Knurl Width - 4 1/2" - 114mm, Control Length - 8" - 203mm, Drilled - YES Replaces OEM # 53100-341-000 Note: These Are Drilled For Wires
Fork Seals
Fork Seals Set/2 35 X 48 X 10.5/11
Fork Dust Seals
Fork Dust Seals Set/2 35 X 53 OEM Ref # 91254-434-003 / 91254-435-003 / 51425-340-000
Stock Type Fork Gaitors
Black Stock Type Fork Gaitors (Set/2) OEM Ref. # 51611-300-000
Fork Seals
Fork Seal Set - 35 x 46 x 11. Made In Japan by OEM supplier. Replaces OEM # 91255-292-003
Progressive Front Fork Springs
Progressive Front Fork Spring Set/2 with Required Spacers and Washers. These Progressive Springs improve handling and overall ride quality. They Stop front end droop and diving during braking while improving cornering stability. A Great Performance upgrade for your Bike!
Fork Dust Boots
Fork Dust Boots Set/2 OEM Ref # 51425-375-003 / 51425-375-005
Fork Gaiters
Fork Gaiters OEM Ref # 51611-300-000 Note: These are about 1.75" shorter then the stock type but will work fine
Fork Spacer Trim Set
Chrome Front Fork Spacer Trim Set/2. These are the Chrome Ribs that Cover the Top of the Fork Boots. Replaces OEM # 51608-300-000
Wheel Seal Kit
Front Wheel Seal Kit 2 Seals 22 x 36 x 8 40 x 50 x 5
Swing Arm Bushing Set
Swing Arm Bushing Set OEM Ref # 52108-457-300 Note: These Replace the factory plastic OEM Type Bushings.
High Performance Kibblewhite Bronze Swingarm Bushing Set
High Performance Kibblewhite Bronze Swingarm Bushing Set/2. Replaces OEM# 52108-457-300, 52108-422-300. Made in the USA by Kibblewhite who have been making High Quality Performance parts for 75+ years. Kibblewhite bronze bushings offers increased durability and better fitment then the OEM type bushings.
Steering Bearing Kit
Tapered Roller Steering Bearing Conversion Kit. Superior to OEM quality, 10X the contact area and less flex. Designed as a drop in replacement for the original bearing. Kit is complete with upper and lower tapered bearing races. High quality made in Japan.
Steering Bearing Kit
Tapered Roller Steering Bearing Conversion Kit. Superior to OEM quality, 10X the contact area and less flex. Designed as a drop in replacement for the original bearing. Kit is complete with upper and lower tapered bearing races. High quality made in Japan.
Steering Bearing Kit
Tapered Roller Steering Bearing Conversion Kit. Superior to OEM quality, 10X the contact area and less flex. Designed as a drop in replacement for the original bearing. Kit is complete with upper and lower tapered bearing races. High quality made in Japan.
Rear Wheel Bearing Retainer
Rear Wheel Bearing Retainer - Sprocket Side - Replaces OEM# 41231-283-000 This retainer is used on the (sprocket side) of the bike.
Front Wheel Bearing Retainer
Front Wheel Bearing Retainer - Replaces OEM# 44643-300-000
Front Wheel Bearing
Front Wheel Bearing with 2 Synthetic Shields - 6302-2RS Size High Quality Made in Japan 2 Used Per Front, Order Quantity you Require
Rear Wheel Bearing
Rear Wheel Bearing with 2 Synthetic Shields - 6304-2RS Size High Quality Made in Japan 2 Used Per Bike Order Quantity you Require
Rear Wheel Bearing
Rear Wheel Bearing with 2 Synthetic Shields - 6305-2RS Size Replaces OEM# 96140-63050-10 High Quality Made in Japan
Billet Aluminum Upper Triple Tree Clamp
Custom Billet Aluminum Machined Upper Triple Tree Clamp. This billet triple has 2X 6mm mounting bosses 50mm apart on the underside of the top triple to accommodate various aftermarket and custom designed instrument mounts for your aftermarket gauges. Designed so the top triple has a rounded top edge with a stylish inset and makes an excellent replacement for the stock cast item when using clip-on bars! This piece was designed to make it very easy for the average Cafe builder to modify their motorcycle. Very High quality, machined in North America. Clip on bars not included and your stock bars will NOT mount to this piece.
Rear Shock Swingarm Bushing
Rear Shock Swingarm Bushing, Replaces OEM# 40548-268-000 19mm Long, 22mm OD, 10mm ID. Sold Each, Order the Quantity you Require