Honda ► CB750K ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB750K with universal parts included that match “muffler gasket”►
- Honda
Premium Athena Cylinder Head Gasket
Premium Athena Brand Cylinder Head Gasket - OEM Ref.# 12251-300-050
Cylinder Sleeve O-Ring Gasket Set
Cylinder Sleeve O-Rings (Set of 4) OEM Ref. # 91304-286-000 - 4 pc. required per Engine
Valve Tappet Cover Gasket Set/8
Valve Tappet Cover Gaskets Set/8. These are made for the stock type Valve Tappet Covers. These replace OEM # 91302-001-020 Note:These will only work on OEM type Tappet covers
Chrome Starter Motor Cover w Gasket
Chrome Starter Motor Cover with Gasket. Replaces OEM # 31280-300-000 (Cover) and OEM # 31282-300-020 (Gasket). Note: If you Require New Hardware for this Cover this Can be Found on our Site
Athena Gasket Set (Top End Set Only)
Athena Top End Gasket Set - Fits: All Honda CB750's (1974-78) Sets made by Athena of Italy the European original equipment supplier to Yamaha, Honda, Kawasaki, Suzuki and all major Italian bike makers. Top Quality ISO-9000 approved. Set includes: 18-7001, Cylinder Base Gasket, OEM # 12191-300-030 18-7002, Cylinder Head Gasket, OEM # 12251-300-050 18-7003, Cam Cover Gasket, OEM # 12391-300-400 18-7068, Cylinder Sleeve O-Ring Gasket Set/4, OEM # 91304-286-000 18-7015, Cylinder Head Nut Cover Set/6, OEM # 91318-300-013 18-7018, Cylinder Stud Packing Set/8, OEM # 12115-300-000 18-7069, Valve Tappet Cover Gasket Set/4, OEM # 91302-001-020 18-7017, Valve Stem Seal Set/8, OEM # 12209-300-000 18-7013, Exhaust Headpipe Gasket Set/4, OEM # 18291-MM5-860
Exhaust Heat Shield with Hardware
Exhaust Heat Shield with Hardware. Includes One Heat Shield for One Muffler and the Hardware required to install it (3 Bolts, 3 Washers, 6 Spacers). Replaces OEM # 18315-300-020 Fits: Stock Type Exhaust on Honda CB750K (1969-76) Note: 2 Heat Shields Required Per Bike, Order the Quantity You Require
Tappet Covers
Finned Tappet Cover - Sold Each Comes With O-Ring gasket High Quality Chrome Finish
Oil Tank Cap with Dipstick
Chrome Oil Tank Cap/Dipstick Assembly with Gasket. Replaces OEM # 55105-300-010
Cylinder Head Nut Cover
Cylinder Head Nut Cover OEM Ref # 91318-300-013
Clutch Arm Seal
Clutch Arm Seal (SB Type) - 14 x 24 x 5 - Replaces OEM # 91202-KFL-841
Oil Pump Rebuild Kit
11 Pc. Oil Pump Rebuild Kit. Use this kit to get your oil pump flowing at maximum capacity for a healthy engine, performing at it's best! Kit includes 1 oil stopper seal, 1 oil stopper spring, 1 oil relief valve spring, 1 oil relief valve o-ring, 3 pump connection o-rings, 2 inner rotor o-rings, 1 steel reinforced center shaft seal, 1 pump body gasket.
Premium Stock Type Stator
Premium Made in the USA ~ Rick's Electrics ~ Stock Style Stator, Replaces OEM # 31102-300-045 / 31102-300-035 / 31102-393-025 / 31102-393-005 / 31102-393-015.
Stock Style Stator
Stock Style Stator, Replaces OEM # 31102-300-045 / 31102-300-035 / 31102-393-025 / 31102-393-005 / 31102-393-015. We had these hard to find stators re-manufactured to keep your CB on the road!
Gas/Fuel Tank Chrome Cap
Gas/Fuel Tank Chrome Cap with Gasket and Hinge Pin (with E-Clip which Allows for easy installation). Replaces OEM # 17510-323-310
Starter Motor Seal
Starter Motor Seal - 60 x 1.4 - Replaces OEM# 31206-286-158 / 31206-402-008
Cylinder Stud Packing Set (8pc)
8pc. set of rubber cylinder head bolt (stud) packings (short tubular rubber seals that fit over dowels) OEM Ref. # 12115-300-000
Starter Motor
Rick's Electrics Starter Motor, Replaces OEM# 31200-300-030 This starter motor features an upgraded 4-Brush permanent magnet design & comes with the battery cable.
Alternator Stator Wire Harness
Alternator Stator Wire Harness, This Harness has the Same 7 Wire Plug as the OEM part and Hooks up Without Alterations. Replaces OEM # 31110-300-154
Special Clutch Washer
Special Angled Clutch Washer (16mm), Replaces OEM# 90481-292-000
Clutch Ball Retainer
Clutch Ball Retainer, Replaces OEM# 22860-300-006
Cast Aluminum Finned Starter Motor Cover
Cast Aluminum Finned Starter Motor Cover, Made in the USA. Replaces OEM # 31280-300-000 This is a new cover designed and produced like the ones from the 70's that aren't made anymore. This cover is delivered in as-cast condition. As such, Sandblasting, painting, or powder coating will be required if you want a look other then the cast aluminum look. As delivered it is a close match for an original patina engine. Note: Gasket and Hardware Not Included with Cover
Custom Black Gas/Fuel Tank Cap ~ Joker Machine
Joker Machine Brand ~ Custom Black Gas/Fuel Tank Flip Up Billet Cap. Includes Cap with a spring loaded alloy flange, replaceable rubber gasket and alloy screw attachment. Replaces OEM # 17510-323-310 Installs easily onto the tank hinges with an alloy screw (not rivets found on the stock set-up) in minutes. Lightweight design is made from a solid block of 1" thick Billet aluminum. Works with stock style latching mechanisms (Sold Separately). High quality CNC machined cap made in the U.S.A.
Clutch Release Actuator Assembly
Clutch Release Actuator Assembly, Replaces OEM# 22830-300-000 / 22860-300-006 / 22820-300-000 / 22841-300-000 / 91301-426-010