Honda ► CB750K ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB750K with universal parts included that match “muffler gasket”►
- Honda
Athena Gasket Set (Top End Set Only)
Athena Top End Gasket Set - Fits: All Honda CB750's (1974-78) Sets made by Athena of Italy the European original equipment supplier to Yamaha, Honda, Kawasaki, Suzuki and all major Italian bike makers. Top Quality ISO-9000 approved. Set includes: 18-7001, Cylinder Base Gasket, OEM # 12191-300-030 18-7002, Cylinder Head Gasket, OEM # 12251-300-050 18-7003, Cam Cover Gasket, OEM # 12391-300-400 18-7068, Cylinder Sleeve O-Ring Gasket Set/4, OEM # 91304-286-000 18-7015, Cylinder Head Nut Cover Set/6, OEM # 91318-300-013 18-7018, Cylinder Stud Packing Set/8, OEM # 12115-300-000 18-7069, Valve Tappet Cover Gasket Set/4, OEM # 91302-001-020 18-7017, Valve Stem Seal Set/8, OEM # 12209-300-000 18-7013, Exhaust Headpipe Gasket Set/4, OEM # 18291-MM5-860
Tappet Covers
Finned Tappet Cover - Sold Each Comes With O-Ring gasket High Quality Chrome Finish
Cylinder Head Nut Cover
Cylinder Head Nut Cover OEM Ref # 91318-300-013
Clutch Arm Seal
Clutch Arm Seal (SB Type) - 14 x 24 x 5 - Replaces OEM # 91202-KFL-841
Oil Pump Rebuild Kit
11 Pc. Oil Pump Rebuild Kit. Use this kit to get your oil pump flowing at maximum capacity for a healthy engine, performing at it's best! Kit includes 1 oil stopper seal, 1 oil stopper spring, 1 oil relief valve spring, 1 oil relief valve o-ring, 3 pump connection o-rings, 2 inner rotor o-rings, 1 steel reinforced center shaft seal, 1 pump body gasket.
Premium Stock Type Stator
Premium Made in the USA ~ Rick's Electrics ~ Stock Style Stator, Replaces OEM # 31102-300-045 / 31102-300-035 / 31102-393-025 / 31102-393-005 / 31102-393-015.
Stock Style Stator
Stock Style Stator, Replaces OEM # 31102-300-045 / 31102-300-035 / 31102-393-025 / 31102-393-005 / 31102-393-015. We had these hard to find stators re-manufactured to keep your CB on the road!
Carb Rebuild Kit
Carb Rebuild Kit. Contains: Float Bowl Gasket, Carb Top Gasket, D432 Slide Needle, Main Jet (#115), Float Needle, Air Spring, Air Screw Plug, Air Fuel Screw, Needle Jet, E-Clip, Metal Washer, 6 O-Rings. - Made in Japan -
Starter Motor Seal
Starter Motor Seal - 60 x 1.4 - Replaces OEM# 31206-286-158 / 31206-402-008
Cylinder Stud Packing Set (8pc)
8pc. set of rubber cylinder head bolt (stud) packings (short tubular rubber seals that fit over dowels) OEM Ref. # 12115-300-000
Gas/Fuel Tank Cap
OEM Style Gas/Fuel Tank Cap with Rubber Gasket Already Installed, Replaces OEM # 17620-399-010 Note: Does not include a chain attached to this cap.
Starter Motor
Rick's Electrics Starter Motor, Replaces OEM# 31200-300-030 This starter motor features an upgraded 4-Brush permanent magnet design & comes with the battery cable.
Alternator Stator Wire Harness
Alternator Stator Wire Harness, This Harness has the Same 7 Wire Plug as the OEM part and Hooks up Without Alterations. Replaces OEM # 31110-300-154
Special Clutch Washer
Special Angled Clutch Washer (16mm), Replaces OEM# 90481-292-000
Clutch Ball Retainer
Clutch Ball Retainer, Replaces OEM# 22860-300-006
Cast Aluminum Finned Starter Motor Cover
Cast Aluminum Finned Starter Motor Cover, Made in the USA. Replaces OEM # 31280-300-000 This is a new cover designed and produced like the ones from the 70's that aren't made anymore. This cover is delivered in as-cast condition. As such, Sandblasting, painting, or powder coating will be required if you want a look other then the cast aluminum look. As delivered it is a close match for an original patina engine. Note: Gasket and Hardware Not Included with Cover
Clutch Release Actuator Assembly
Clutch Release Actuator Assembly, Replaces OEM# 22830-300-000 / 22860-300-006 / 22820-300-000 / 22841-300-000 / 91301-426-010
Muffler Reducer
One piece muffler Reducer sleeve. Sleeve is 1" long and reduces universal mufflers with 44-45mm. ID (1.75") down to 38mm. (1.5").
Black Shorty Muffler
Black Shorty Muffler. Super compact design 12" Long, Fits 1 1/2" or 1 3/4" headpipes. Complete with mounting hardware, Friction fit and cannot use clamps. The mounting bracket will hold it in place. Removable glass packed baffle. Mounts on left, or right side. Sold Each
Chrome Shorty Muffler
Chrome Shorty Muffler. Super compact design 12" Long, Fits 1 1/2" or 1 3/4" headpipes. Complete with mounting hardware, Friction fit and cannot use clamps. The mounting bracket will hold it in place. Removable glass packed baffle. Mounts on left, or right side. Sold Each
Flat Black Muffler
Flat Black Muffler 19" Length with a 1 3/4" inlet (1 1/2" and 1 5/8" reducer kit included), Straight through perforated core type non removable baffle. Includes mounting clamp and universal style hanger that is used with slotted channel on backside of muffler for left or right side use. Sold each
Flat Black Tapered Muffler
Flat Black Tapered Muffler Overall length 16.25", Inlet ID: 1-3/4" Or 1-1/2" if you use the included reducer shims. Comes with slide mounting bracket. High quality construction with a non removable mechanical baffle. Can be used on the left or right side. Sold Each