Honda ► CB750K ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB750K with universal parts included►
- Honda
Exhaust Stud Set
Exhaust Stud Set. Includes 8 Exhaust Studs and 8 Flange Nuts.
Headlight Bucket Case
Black Headlight Bucket / Case, Stock Design - Replaces OEM # 61301-300-020B
Rear Fender Eliminator
Rear Fender Eliminator. Includes holes for custom tail light and license plate install. These are Great for Cafe builds and custom work! If you want a Licence Plate Frame to go with this, Our #73-0087 or 73-0088 fit perfectly, Tailllight #11-2325
Velocity Stack Set
Velocity Stack Set. These Velocity Stacks are a High Quality, 39mm ID, Taper Tipped Build. Set Comes Complete with 4 Velocity Stacks with Debris Screens, Set Screws and Set Screw Allen Wrench. These install easily and look amazing once installed!
Fuse Box Assembly *Damaged Tabs*
*Damaged Tabs* Fuse Box Assembly Complete with 15Amp Fuses, Replaces OEM# 38200-MF9-405. This Fuse Box Typically has 4 Sets of Attachment Tabs on the back of the assembly used to fasten to the bike. However, several had tabs broken during transit so our loss is your gain! This unit has absolutely nothing wrong with the electrics. The unit your purchasing has damage to some or all of the tabs used to fasten the unit to your bike. Due to where it is attached all tabs should not be needed for installation. You may or may not need to find a solution such as glue/tape etc. to install but it should not pose any problems. As there is a cover over this unit if you use a little duct tape etc. nobody will ever know.
Fuse Box Assembly *Damaged Tabs*
*Damaged Tabs* Fuse Box Assembly Complete with 10Amp Fuses, Replaces OEM# 38200-425-005. This Fuse Box Typically has 4 Sets of Attachment Tabs on the back of the assembly used to fasten to the bike. However, several had tabs broken during transit so our loss is your gain! This unit has absolutely nothing wrong with the electrics. The unit your purchasing has damage to some or all of the tabs used to fasten the unit to your bike. Due to where it is attached all tabs should not be needed for installation. You may or may not need to find a solution such as glue/tape etc. to install but it should not pose any problems. As there is a cover over this unit if you use a little duct tape etc. nobody will ever know.
Fork Tube Set
Fork Tube Set/2, Length (580mm or 22 13/16"), 35mm OD. Fits: Honda CB750K (1972) Higher then Frame# 2093730 Only, CB750K (1973-76) NOTE: LENGTH is 22 13/16", one Inch Shorter then Stock Length for these Models below. Fits: Honda CB750K (1977) Higher then Frame# 2707508 Only, CB750K (1978), CB750F (1977-78) Supersport, CB750A (1976-78) Hondamatic Before ordering Please Confirm 22 13/16" is the Length you would like
Chrome Stock Type Front Fender
Chrome Stock Type Front Fender, Replaces OEM # 61100-341-700XW Includes the chrome support struts, bracket for the speedo cable and the bracket to hold the brake hose in place.
Chrome Stock Type Rear Fender
Chrome Stock Type Rear Fender, Replaces OEM # 80100-341-000
Stock Type Gas/Fuel Tank
Stock Type Gas/Fuel Tank. Tank comes in primer grey ready for you to paint your color of choice. Fits: Honda CB750K (1969-74) Does not include gas cap #20-0045, petcock #20-8039, emblems or any other items.
Stock Type Gas/Fuel Tank
Stock Type Gas/Fuel Tank. Tank comes in primer grey ready for you to paint your color of choice. Fits: Honda CB750K (1975-76) Does not include gas cap #20-0045, petcock #20-8038, emblems or any other items.
Rectifier/Regulator
Rectifier-Regulator: This is a combination unit which will replace the OEM regulator and rectifier. This has the OEM type ground wiring and Stock Type Plugs. Dimensions 80mm Length, 94mm Width, 27mm Height, Hole Distance 70.0mm Center to Center. Instructions not included.
Black Stock Type Front Fender
Black Stock Type Front Fender, Replaces OEM # 61100-341-700XW Includes the support struts, bracket for the speedo cable and the bracket to hold the brake hose in place. Fits: Honda CB750K (1972) - Frame # 2093731 and Higher, CB750K (1973-75), CB750K (1976) - Frame # 2540001 to 2575894 CB550K (1974-76)
Black Stock Type Rear Fender
Black Stock Type Rear Fender, Replaces OEM # 80100-341-000
Custom Black Gas/Fuel Tank Cap ~ Joker Machine
Joker Machine Brand ~ Custom Black Gas/Fuel Tank Flip Up Billet Cap. Includes Cap with a spring loaded alloy flange, replaceable rubber gasket and alloy screw attachment. Replaces OEM # 17510-323-310 Installs easily onto the tank hinges with an alloy screw (not rivets found on the stock set-up) in minutes. Lightweight design is made from a solid block of 1" thick Billet aluminum. Works with stock style latching mechanisms (Sold Separately). High quality CNC machined cap made in the U.S.A.
Custom Black Gas/Fuel Tank Cap Latch Assembly ~ Joker Machine
Joker Machine Brand ~ Custom Black Gas/Fuel Tank Cap Latch Assembly, Includes Black Latch, Return Spring and Alloy Screw attachment with nut. A fully CNC machined, billet aluminum alternative to the discontinued cast thumb latches. Install is easily made with the provided alloy screw attachment with nut. Much more durable and stronger than the original die-cast piece. High quality CNC machined part made in the U.S.A. Ties in great with our Custom Black Gas/Fuel Tank Cap (#73-1156)
Oil Pressure Gauge Assembly ~ Black ~ Joker Machine
Joker Machine Brand ~ Oil Pressure Gauge Assembly. Black Colored Mount Assembly with a Silver Colored Stainless Steel Marshall liquid filled gauge 1 1/2" (38mm) diameter, 0 to 100 PSI. Easily installs on the oil gally port above the points cover in minutes! Features 2 built-in Neoprene rubber o-rings recessed in 2 fittings that have a unique rotating section that enables you to easily position the gauge for perfect rider visibility. Just loosen the billet hex fitting, rotate into position, then tighten. High quality made in the U.S.A
TC Bros. Forward Controls Kit
TC Bros. Brand Bolt-On Forward Controls Kit. Kit includes a pair of forward controls featuring CNC machined, knurled aluminum pegs. The mounting plates are heavy duty powder coated steel and bolt on in place of your front motor mount on one side and u-bolt to your frame on the other side. The spacers are TIG welded to the mounting plates. Everything bolts on using your stock mounting hardware and with no frame modifications. The only welding required is a tab that is welded to your stock brake pedal in order to attach the linkage rods. It is easily done and mounting instructions with pictures are included with each kit. This kit makes long trips much more comfortable due to the fact that your legs are extended forward rather than bent. Great for choppers, bobbers, or even stock bikes. High Quality, Made in the USA. Linkage Kit Not Included
CB750 Engine Stand
CB750 SOHC Engine Rebuild Stand. Make your engine rebuild a lot easier with this engine stand. Very rigid and easily secured to your work bench using holes found in the base of the stand. Powder coated gloss black for a durable finish. High Quality, Made in the USA.
TC Bros. Forward Controls Kit
TC Bros. Brand Bolt-On Forward Controls Kit. Kit includes a pair of forward controls featuring CNC machined, knurled aluminum pegs. The mounting plates are heavy duty powder coated steel and bolt to your front motor mounts. The spacers are TIG welded to the mounting plates. Everything bolts on using the supplied mounting hardware with no frame modifications. Mounting instructions with pictures are included with each kit. This kit makes long trips much more comfortable due to the fact that your legs are extended forward rather than bent. Great for choppers, bobbers, or even stock bikes. High Quality, Made in the USA. Linkage Kit Not Included, We Sell that part #73-1164
Stock Type Muffler Set.
Stock Type Muffler Set. These brand new mufflers are the 341 Style with non replaceable internal baffle. Beautiful high quality, newly produced stock type muffler set. High quality chrome. Buy this now to make your bike stand out! Fits: Honda CB750K (1972-76) Hardware Sold Separately
Stock Type Muffler Set
Stock Type Muffler Set These brand new mufflers are the 300 Style muffler set. Beautiful high quality, newly produced stock type muffler set. High quality chrome. Buy this now to make your bike stand out! Fits: Honda CB750K (1969-71) Hardware Sold Separately
Stock Type Muffler Set
Stock Type Muffler Set These brand new mufflers are the 405 Style muffler set. Beautiful high quality, newly produced stock type muffler set. High quality chrome. Buy this now to make your bike stand out! Fits: Honda CB750K (1977-78) Hardware Sold Separately
Electronic Ignition System
Electronic Ignition System. Direct plug-in fitment. Increase RPM 100% tested before shipment, high reliability and high performance! This ignition can be used with your stock coils or any other coils 3 ohms or higher.
Front Sprocket ~ 17 Tooth
Front Sprocket ~ 17 Tooth Replaces OEM# 23801-333-000 / 23801-300-315 Please Count your sprocket teeth and check your chain length before ordering to ensure this is correct for your bike. Please note: for the CB450K (1968-69) - some bikes used 15 tooth sprockets, for the CB750K (1969-70) use this sprocket upto engine #SN1003527 only, for the CL450 (1967/1969) some bikes used 15 or 16 tooth sprockets.