Honda ► CB750K ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB750K with universal parts included►
- Honda
Accelerator Pump Joint Hose
Accelerator Pump Joint Hose. 12" Piece. 8mm Outer Diameter, 4mm Inner Diameter. Order the quantity you require. Note: Be sure to remove and then re-install the old brass nozzles from the old joint hoses.
Carb Overflow Tube Hose
Carb Overflow Tube Hose. 24" Piece. 8mm Outer Diameter, 4mm Inner Diameter. Sold Each, Order the quantity you require
Carb Float
Carb Float with Pin, Replaces OEM # 16013-300-004
Carb Float Setting Tool (CB750 1969-76 Models)
Carb Float Setting Tool. Use this tool to help set your floats with ease! This pre-set float setting gauge is for the CB750 1969-76K and 1975-76F Supersport models.
Float Bowl Gasket
Float Bowl Gasket OEM Ref # 16023-300-004
Fuel Petcock
Fuel Petcock OEM Ref # 16950-300-020
Fuel Petcock Screen
Replacement Fuel Petcock Screen for the stock type fuel petcock. Replaces OEM# 16957-268-010
Steel Front Sprocket - 17 Tooth X 530
Steel Front Sprocket - 17 Tooth - Replaces OEM # 23801-300-010 For 530 Chain Setup as came stock with the bikes below. Fits: FRONT on Honda CB750K (1969-70) - Use from Engine # 1003528 or Higher, CB750F (1975-76) Supersport, CB750A (1976) Hondamatic Please Count your sprocket teeth and check your chain length before ordering to ensure this is correct for your bike
Negative (-) Battery Cable
Negative (-) Battery Cable (Ground Cable). Replaces OEM # 32601-MG9-000
Positive (+) Battery Cable
Positive (+) Battery Cable with Rubber End Covers. Replaces OEM # 32401-300-010
Oil Pressure Gauge Assembly ~ Black Face Plate
Oil Pressure Gauge Assembly. Includes a silver colored liquid filled gauge with a black face plate, (44mm) diameter, 0 to 100 PSI. Billet aluminum oil galley adapter, o-ring and a chrome 90° fitting included. Easily installs on the oil gally port above the points cover in minutes!
Oil Pressure Gauge Assembly ~ White Face Plate
Oil Pressure Gauge Assembly. Includes a silver colored liquid filled gauge with a white face plate, (44mm) diameter, 0 to 100 PSI. Billet aluminum oil galley adapter, o-ring and a chrome 90° fitting included. Easily installs on the oil gally port above the points cover in minutes!
Oil Pressure Gauge Assembly ~ Carbon Face Plate
Oil Pressure Gauge Assembly. Includes a silver colored liquid filled gauge with a carbon looking face plate, (44mm) diameter, 0 to 100 PSI. Billet aluminum oil galley adapter, o-ring and a chrome 90° fitting included. Easily installs on the oil gally port above the points cover in minutes!
Oil Pressure Gauge Assembly ~ Metal Machined Face Plate
Oil Pressure Gauge Assembly. Includes a silver colored liquid filled gauge with a metal machined design looking face plate, (44mm) diameter, 0 to 100 PSI. Billet aluminum oil galley adapter, o-ring and a chrome 90° fitting included. Easily installs on the oil gally port above the points cover in minutes!
Rectifier/Regulator ~ Lithium Ion Battery Compatible
Rick's Electric Brand Lithium Ion Battery Compatible Rectifier-Regulator. Designed with a lower voltage set point to work with lithium ion batteries only. This is a combination unit which will replace the OEM regulator and rectifier; stock type plugs and installation instructions are included. Dimensions 70mm Length, 94mm Width, 27mm Height, Hole Distance 80mm Center to Center. Note: May require a custom mounting job. High quality Part. This is Not for use with standard lead acid batteries. The voltage set point is 14V +/- .2. Please ensure this set point is correct for your battery before attempting installation.
Starter Brush Set
Starter Brush Set/2 1Pc Insulated Leads 1Pc Non-Insulated Leads 12mm x 14mm x 6mm For Misuba 2 Brush Starter. OEM Ref # 31201-292-158 / 31201-MG9-004
Rectifier Regulator
Universal Type Rectifier Regulator 8 Wires - No End Terminals
Starter Motor
Rick's Electrics Starter Motor, Replaces OEM# 31200-300-030 This starter motor features an upgraded 4-Brush permanent magnet design & comes with the battery cable.
Rectifier/Regulator
Rick's Electric Brand OEM Style Honda Rectifier-Regulator: This is a combination unit which will replace the OEM regulator and rectifier; stock type plugs and installation instructions are included. Dimensions 68mm Length, 94mm Width, 26mm Height, Hole Distance 80.0mm Center to Center. High quality Part. Note: May require a custom mounting job. Works great if attached with one bolt and nut where the safety starter switch was originally located (can bypass that switch).
Premium Stock Type Stator
Premium Made in the USA ~ Rick's Electrics ~ Stock Style Stator, Replaces OEM # 31102-300-045 / 31102-300-035 / 31102-393-025 / 31102-393-005 / 31102-393-015.
Wire Harness
Main Wire Harness Loom - OEM Ref. # 32100-300-050
Oil Pressure Switch Wire Assembly
Oil Pressure Switch Wire Assembly. Includes the Wire and Rubber Cover. Replaces OEM # 31270-300-154 / 31270-300-005
Alternator Stator Wire Harness
Alternator Stator Wire Harness, This Harness has the Same 7 Wire Plug as the OEM part and Hooks up Without Alterations. Replaces OEM # 31110-300-154
Starter Clutch Repair Kit
Starter Clutch Repair Kit
Handlebar - Stock Type ~ CB750 1969-71
Stock Type Handlebar for the CB750K (1969-71) - Chrome. Drilled for wires like the OEM type. Bar Diameter - 7/8" - 22mm, Length - 32" - 812mm, Pull Back - 5 3/8" - 136mm, Inner Rise - 5 1/4" - 133mm, End Rise - 6 7/8" - 175mm, Center Width - 6 1/2" - 165mm, Base Width - 9 1/2" - 241mm, Knurl Width - 4 1/2" - 114mm, Control Length - 9" - 228mm, Drilled - YES Replaces OEM # 53100-300-000 Note: These Are Drilled For Wires
Condenser
Condenser OEM Ref # 30250-300-154 / 30250-300-005
Stock Type Fork Gaitors
Black Stock Type Fork Gaitors (Set/2) OEM Ref. # 51611-300-000
Fork Seals
Fork Seal Set - 35 x 46 x 11. Made In Japan by OEM supplier. Replaces OEM # 91255-292-003
Progressive Front Fork Springs
Progressive Front Fork Spring Set/2 with Required Spacers and Washers. These Progressive Springs improve handling and overall ride quality. They Stop front end droop and diving during braking while improving cornering stability. A Great Performance upgrade for your Bike!
Fork Gaiters
Fork Gaiters OEM Ref # 51611-300-000 Note: These are about 1.75" shorter then the stock type but will work fine
Fork Spacer Trim Set
Chrome Front Fork Spacer Trim Set/2. These are the Chrome Ribs that Cover the Top of the Fork Boots. Replaces OEM # 51608-300-000
Wheel Seal Kit
Front Wheel Seal Kit 1 Seal
Steering Bearing Kit
Tapered Roller Steering Bearing Conversion Kit. Superior to OEM quality, 10X the contact area and less flex. Designed as a drop in replacement for the original bearing. Kit is complete with upper and lower tapered bearing races. High quality made in Japan.
Rear Wheel Bearing Retainer
Rear Wheel Bearing Retainer - Sprocket Side - Replaces OEM# 41231-283-000 This retainer is used on the (sprocket side) of the bike.
Front Wheel Bearing Retainer
Front Wheel Bearing Retainer - Replaces OEM# 44643-300-000
Front Wheel Bearing
Front Wheel Bearing with 2 Synthetic Shields - 6302-2RS Size High Quality Made in Japan 2 Used Per Front, Order Quantity you Require
Rear Wheel Bearing
Rear Wheel Bearing with 2 Synthetic Shields - 6304-2RS Size High Quality Made in Japan 2 Used Per Bike Order Quantity you Require
Rear Shock Swingarm Bushing
Rear Shock Swingarm Bushing, Replaces OEM# 40548-268-000 19mm Long, 22mm OD, 10mm ID. Sold Each, Order the Quantity you Require
Master Cylinder Reservoir Cap
Master Cylinder Cap with Plastic O-Ring. Replaces OEM # 45513-341-771 This style of master cylinder cap was discontinued long ago by Honda. We have had these produced again to keep your bike looking sharp. Spruce up your Master Cylinder with one of these great looking master cylinder caps!
Master Cylinder Reservoir Cap Plastic O-Ring
Master Cylinder Reservoir Cap Plastic O-Ring, Replaces OEM # 45521-MJ6-006
Reservoir Cap & Diaphragm
Reservoir Cap & Diaphragm Round Thread On Type OEM Ref # 43515-MJ6-006 / 45520-300-000
Front Brake Caliper Piston
Front Brake Caliper Piston. Replaces OEM # 45107-300-003
Front Brake Caliper Piston Sealing Ring
Front Brake Caliper Piston Sealing Ring, Replaces OEM # 45108-300-003
Speedo Gear Plug
Speedo Gear Plug - Plug 15mm Outer Diameter, 22mm Long. This Plug is Great for Keeping your Original Speedo Drive Gear Clean.
Rear Brake Shoes
Rear Brake Shoes Pk/2 Diameter: 178.5mm Width: 39mm OEM Ref # 43120-393-006
Front Brake Pads
Front Brake Pads Pk/2 OEM Ref # 45105-341-000A
Deluxe Rear Brake Shoe Set
Deluxe Kevlar/Carbon Water Grooved Rear Brake Shoe (Set/2) - OEM Ref # 06430-393-405
Tachometer Cable Clamp
Chrome Tachometer Cable Clamp (Holder). Replace that Old Rusted, Worn Out Clamp with a Brand New Great Looking Chrome Tach Cable Clamp. Replaces OEM # 50462-323-010
Handlebar Clamp Hardware Set
Handlebar Clamp Hardware Set. Set Includes 4 Chrome Plated Bolts and 4 Washers. This Hardware Set is for the Stock Type Clamp (Holder) that Attaches Over the Handlebar. Replaces OEM # 93101-08040-0B X4 (Bolts) and 90518-921-000 X4 (Washers). Fits: Stock Type Handlebar Clamps on the Honda CB750K (1969-75)
Brake Rod Spring
Brake Rod Spring. Replaces OEM # 95014-73100