Honda ► CB750K ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB750K with universal parts included►
- Honda
Kick Starter Joint Spring
Kick Starter Joint Spring. This Spring Goes onto the Kick Starter Knuckle Pin (The Pin that Connects the Kick Starter to the Bike). Replaces OEM # 28292-250-010
Rear Brake Light Stop Switch Spring
Rear Brake Light Stop Switch Spring. This is the Spring that Attaches to the Rear Stop Light Switch. Replaces OEM # 35357-300-000
Clutch Lever Return Spring
Clutch Lever Return Spring. This is the Spring Located Behind the Clutch Cover. Replaces OEM # 22815-300-000
Headlight Adjusting Screw & Spring Set
Headlight Adjusting Screw & Spring Set. Each Set Includes One Screw and One Spring. Replaces OEM # 33103-346-670 (Screw) and OEM # 33107-300-003 (Spring)
Rear Sprocket Washer Set
Rear Sprocket Tongued Lock Washer (Pack of 2). Replaces OEM # 94108-17000
Kick Starter Stopper Spring with Steel Ball
Kick Starter Stopper Spring with Steel Ball Set. Replaces OEM # 28333-300-000 (Spring) and OEM # 96211-08000 (Steel Ball).
Cylinder Dowel Pin (12x22mm)
Cylinder Dowel Pin 12x22mm Size. Replaces OEM # 94301-12220 Note: 2 Used Per Bike, Order the Quantity you Require
Cylinder Dowel Pin (12x15mm)
Cylinder Dowel Pin 12x15mm Size. Replaces OEM # 94301-12150 Note: Sold Each, Order the Quantity you Require
Front Brake Caliper Adjuster Set
Front Brake Caliper Adjuster Set. Includes Adjusting Bolt, Spring, Washer and Nut.
Front Brake Caliper Bleed Screw
Front Brake Caliper Bleed Screw. Replaces OEM # 45109-300-003
Brake Caliper Bleed Screw Rubber Cap (Stock Type)
Stock Type Brake Caliper Bleed Screw Rubber Cap. These are the Same Design Rubber Caps as the Originals from the Factory. Replaces OEM # 45110-300-003 / 45224-579-013
Flange Knock Bolt (Set/2)
Flange Knock Bolt (Set/2). These Bolts Fasten to the Cam Sprocket. Replaces OEM # 90082-HA0-000
Hydraulic Brake Light Switch
Hydraulic Brake Light Switch - OEM Ref # 35350-300-006 / 35350-300-016 / 341-83980-30-00 10mm x M1.25 thread
Swingarm Pivot Bolt Locknut with Washer
Swingarm Pivot Bolt Locknut with Locknut Washer. Replaces OEM # 90354-268-000 (Locknut) and OEM # 90526-268-000 (Washer).
Swingarm Dust Seal Cap (Set/2)
Swingarm Dust Seal Metal Cap (Set/2). These Metal Caps go on the Ends of the Swingarm Pivot. Replaces OEM # 52144-283-010 X2
Tail Light Mounting Hardware Set
Tail Light Mounting Hardware Set (8 Pc. Set). This set is used to mount your tail Light to the tail Light bracket. Each set Includes 2X Rubber Grommets, 2X Collars, 2X Bolts and 2X Washers.
Fuel Petcock Gasket
Fuel Petcock Gasket. Replaces OEM # 16955-268-020
Special Clutch Washer
Special Angled Clutch Washer (16mm), Replaces OEM# 90481-292-000
Front Brake Rotor
Front Brake Rotor. Replaces OEM# 45120-392-000 / 45120-300-040 / 45120-341-000
Exhaust Heat Shield with Hardware
Exhaust Heat Shield with Hardware. Includes One Heat Shield for One Muffler and the Hardware required to install it (3 Bolts, 3 Washers, 6 Spacers). Replaces OEM # 18315-300-020 Fits: Stock Type Exhaust on Honda CB750K (1969-76) Note: 2 Heat Shields Required Per Bike, Order the Quantity You Require
Kick Starter Return Spring
Kick Starter Return Spring. Replaces OEM # 28261-300-010
Master Cylinder Rubber Boot
Master Cylinder Rubber Boot. This Boot Attaches to where the Brake Hose Joins to the Master Cylinder. Replaces OEM # 45522-300-010
Center Stand Spring
Center Stand Spring. Replaces OEM # 95014-71702
Clutch Center Nut Removal Tool
Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Inside diameter 24mm, use with 3/8" driver.
Clutch Center Nut Removal Tool ~ Premium
Premium Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Both ends with 1/2 drive extension bar, Diameter 20 x 24.
Ignition Switch Nut Tool
Ignition Switch Nut Tool, used to loosen and tighten the igntion switch nut properly without causing any damage to the switch.
Clutch Spring Set
Clutch Spring Set
Clutch Plate
Clutch Plate 7 Pieces Required .138" Thickness OEM Ref # 22201-300-000 / 22201-371-000
Steel Clutch Plate
Steel Clutch Plate 6 Pieces Required OEM Ref # 22321-283-000 / 22321-MG8-000
Carb Holder Set
Carb Holder Set (Set of 4)
Carb Air Box Rubber Boot
Carburetor to Air Box Rubber Boot. Replaces OEM # 17253-341-300 Note: 4 Boots Used Per Bike, Order Quantity you Require
Carb Fuel Line O-Ring Kit
Carb Fuel Line O-Ring 12Pc Kit Includes: 8 Carb Fuel Connector Tube O-Rings and 4 Float Bowl Drain Seal Connector Tube O-Rings (The 4 tubes that connect the 4 carbs together).
Float Bowl Drain Screw O-Rings Pk/4
Float Bowl Drain Screw O-Rings Pk/4
Air Filter Cover O-Rings Pk/2
Air Filter Cover Bolt O-Rings Pk/2, Replaces OEM# 91301-704-000
Deluxe Carb Rebuild Kit
Carb Rebuild Kit. Contains: Float Bowl Gasket, Top Cover Gasket, Float Needle (2.0) & Seat with Float Needle Washer, Main Jets #120 and #140, Slow Jet (#40), Slide Needle & Clip, Air Screw & Spring, Jet Needle Retainer and Assorted Washers. - Made in Japan -
Carb Rebuild Kit
Carb Rebuild Kit Includes Items Pictured High Quality - Made In Japan 1 Kit Needed Per Carb
1969-70 Performance Main Jet Kit
1969-70 Performance Main Jet Kit. Kit includes a total of 16 Main Jets for Keihin Carbs. Use this jet kit to unleash the extra power you should have from your aftermarket exhaust, flee flowing air filters or any engine mods you have made. Kit includes Main Jets #140 (X4), #142 (X4), #145 (X4), #148 (X4)
Float Needle & Seat
Float Needle & Seat High Quality - Made In Japan OEM Ref # 16011-302-004 / 16011-375-004
Carburetor Needle Jet Holder
Carburetor Needle Jet Holder. Replaces OEM # 16139-300-004 Note: Sold Each, One Used per Carburetor
Front Signal Lamp Stay Nut & Washer Set
Front Signal Lamp Stay Nut & Washer Set. These are the Nuts and Washers that thread into the Front Turn Signal Stays. Set includes 2 Nuts and 2 Washers, Enough for both Front Signal Stays.
Lens Screw
Tail Light Lens Screws, Pack of 10. Replaces OEM # 93500-04050-4J ISO Std. Pitch - Steel Plated Size: 4 x 50mm
Fuel Petcock Screw and Washer Set
Set of 2 Chrome Plated Fuel Petcock Screws with 2 Fibre Washers. These Screws replace OEM # 93500-06028-0A These screws fasten the fiber washers to the inside of the petcock and attach to the Fuel Tank. It is always a good idea to replace these when installing a New Fuel Petcock on your CB750K (1969-74), CB550K (1974) or CB500K (1971-73). Purchase these with our Petcock #20-8039
Speedometer / Tachometer Glass Lens Rubber Seal
Speedometer or Tachometer Glass lens Rubber Seal. This seal is used when replacing the glass on the Speedo or Tach. Fits: All 92mm (3.6") glass lenses. Sold each, order the quantity you require
Tachometer & Speedometer Jewel Set
Tachometer & Speedometer Jewel Set. Includes Four Jewels/Lenses: Red (Hi-Beam), Orange (Turn Signals), Green (Neutral) and Red (Oil Pressure).
Speedometer Tripmeter Reset Knob
Speedometer Tripmeter Reset Knob, Replaces OEM# 37237-300-000 These buttons are often damaged and are no longer available from Honda. This reproduction knob is the finishing touch for your precious speedo meter. Fits to many speedos. Made for 3mm shafts.
Sandcast Type Gauge Cover with Lens
Sandcast Type Gauge Cover with Lens. With these reproduction gauge covers, you can recondition your gauges so that they will look like new! These covers are unique and the best quality on the market (Made in the United Kingdom). The interior has the correct light green colour. This listing contains one Gauge Cover, order 2 if reconditioning both gauges. Fits: Honda CB750K (1969-70) Sandcast Version
Speedometer / Tachometer Internal Rubber Seal
Speedometer / Tachometer Internal Rubber Seal. This internal rubber seal replaces the ripped, dried or missing rubber internal seal. This internal rubber seal fits to any stock type Honda CB750 ND brand gauges.
Fuel Petcock Gasket
Fuel Petcock Gasket / O-Ring, Replaces OEM# 16997-273-006 / 16960-011-000 This is the o-ring that goes between the fuel petcock body and the gas tank. Please ensure you have a stock gas tank prior to ordering
Shock Absorber Washer
Shock Absorber Washer, Used when Installing Shocks. Replaces OEM # 90521-292-000 Note: Washers sold Each, order the quantity you require
OEM Type Shock Absorber Bolt
Chrome Shock Absorber Bolt, Replaces OEM # 93201-10032-0B / 93200-10032-0A Note: 2 Bolts Used Per Bike, Order the Quantity you Require