Honda ► CB750K ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB750K with universal parts included►
- Honda
Front Brake Pads
Front Brake Pads Pk/2 OEM Ref # 45105-341-000A
Deluxe Rear Brake Shoe Set
Deluxe Kevlar/Carbon Water Grooved Rear Brake Shoe (Set/2) - OEM Ref # 06430-393-405
Tachometer Cable Clamp
Chrome Tachometer Cable Clamp (Holder). Replace that Old Rusted, Worn Out Clamp with a Brand New Great Looking Chrome Tach Cable Clamp. Replaces OEM # 50462-323-010
Handlebar Clamp Hardware Set
Handlebar Clamp Hardware Set. Set Includes 4 Chrome Plated Bolts and 4 Washers. This Hardware Set is for the Stock Type Clamp (Holder) that Attaches Over the Handlebar. Replaces OEM # 93101-08040-0B X4 (Bolts) and 90518-921-000 X4 (Washers). Fits: Stock Type Handlebar Clamps on the Honda CB750K (1969-75)
Brake Rod Spring
Brake Rod Spring. Replaces OEM # 95014-73100
Kick Starter Joint Spring
Kick Starter Joint Spring. This Spring Goes onto the Kick Starter Knuckle Pin (The Pin that Connects the Kick Starter to the Bike). Replaces OEM # 28292-250-010
Rear Brake Light Stop Switch Spring
Rear Brake Light Stop Switch Spring. This is the Spring that Attaches to the Rear Stop Light Switch. Replaces OEM # 35357-300-000
Clutch Lever Return Spring
Clutch Lever Return Spring. This is the Spring Located Behind the Clutch Cover. Replaces OEM # 22815-300-000
Headlight Adjusting Screw & Spring Set
Headlight Adjusting Screw & Spring Set. Each Set Includes One Screw and One Spring. Replaces OEM # 33103-346-670 (Screw) and OEM # 33107-300-003 (Spring)
Rear Sprocket Washer Set
Rear Sprocket Tongued Lock Washer (Pack of 2). Replaces OEM # 94108-17000
Kick Starter Stopper Spring with Steel Ball
Kick Starter Stopper Spring with Steel Ball Set. Replaces OEM # 28333-300-000 (Spring) and OEM # 96211-08000 (Steel Ball).
Cylinder Dowel Pin (12x22mm)
Cylinder Dowel Pin 12x22mm Size. Replaces OEM # 94301-12220 Note: 2 Used Per Bike, Order the Quantity you Require
Cylinder Dowel Pin (12x15mm)
Cylinder Dowel Pin 12x15mm Size. Replaces OEM # 94301-12150 Note: Sold Each, Order the Quantity you Require
Front Brake Caliper Adjuster Set
Front Brake Caliper Adjuster Set. Includes Adjusting Bolt, Spring, Washer and Nut.
Front Brake Caliper Bleed Screw
Front Brake Caliper Bleed Screw. Replaces OEM # 45109-300-003
Brake Caliper Bleed Screw Rubber Cap (Stock Type)
Stock Type Brake Caliper Bleed Screw Rubber Cap. These are the Same Design Rubber Caps as the Originals from the Factory. Replaces OEM # 45110-300-003 / 45224-579-013
Flange Knock Bolt (Set/2)
Flange Knock Bolt (Set/2). These Bolts Fasten to the Cam Sprocket. Replaces OEM # 90082-HA0-000
Starter Motor Bolt (Set/2)
Starter Motor Flange Bolt Set/2. Replaces OEM # 95700-06056-00
Hydraulic Brake Light Switch
Hydraulic Brake Light Switch - OEM Ref # 35350-300-006 / 35350-300-016 / 341-83980-30-00 10mm x M1.25 thread
Swingarm Pivot Bolt Locknut with Washer
Swingarm Pivot Bolt Locknut with Locknut Washer. Replaces OEM # 90354-268-000 (Locknut) and OEM # 90526-268-000 (Washer).
Rear Sprocket Bolt & Nut Set
Rear Sprocket Stud Bolt (12x54) & Nut Set. Set includes 4 Stud Bolts and 4 Nuts. These Stud Bolts Fasten to the Centre Wheel Flange and Rear Sprockets. Replaces OEM # 90128-341-000 X4 (Bolts), 94030-12000 X4 (Nut)
Swingarm Dust Seal Cap (Set/2)
Swingarm Dust Seal Metal Cap (Set/2). These Metal Caps go on the Ends of the Swingarm Pivot. Replaces OEM # 52144-283-010 X2
Tail Light Mounting Hardware Set
Tail Light Mounting Hardware Set. This Set is Used to Mount the Tail Light Bracket. This 12pc Set Includes 4pc Tail Light Setting Bolts, 4pc Tail Light Setting Washer and 4pc Rubber Fender Cushion.
Fuel Petcock Gasket
Fuel Petcock Gasket. Replaces OEM # 16955-268-020
Special Clutch Washer
Special Angled Clutch Washer (16mm), Replaces OEM# 90481-292-000
Front Brake Rotor
Front Brake Rotor. Replaces OEM# 45120-392-000 / 45120-300-040 / 45120-341-000
Exhaust Heat Shield with Hardware
Exhaust Heat Shield with Hardware. Includes One Heat Shield for One Muffler and the Hardware required to install it (3 Bolts, 3 Washers, 6 Spacers). Replaces OEM # 18315-300-020 Fits: Stock Type Exhaust on Honda CB750K (1969-76) Note: 2 Heat Shields Required Per Bike, Order the Quantity You Require
Kick Starter Return Spring
Kick Starter Return Spring. Replaces OEM # 28261-300-010
Master Cylinder Rubber Boot
Master Cylinder Rubber Boot. This Boot Attaches to where the Brake Hose Joins to the Master Cylinder. Replaces OEM # 45522-300-010
Center Stand Spring
Center Stand Spring. Replaces OEM # 95014-71702
Clutch Center Nut Removal Tool
Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Inside diameter 24mm, use with 3/8" driver.
Clutch Center Nut Removal Tool ~ Premium
Premium Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Both ends with 1/2 drive extension bar, Diameter 20 x 24.
Ignition Switch Nut Tool
Ignition Switch Nut Tool, used to loosen and tighten the igntion switch nut properly without causing any damage to the switch.
Clutch Spring Set
Clutch Spring Set
Clutch Plate
Clutch Plate 7 Pieces Required .138" Thickness OEM Ref # 22201-300-000 / 22201-371-000
Steel Clutch Plate
Steel Clutch Plate 6 Pieces Required OEM Ref # 22321-283-000 / 22321-MG8-000
Carb Holder Set
Carb Holder Set (Set of 4)
Carb Air Box Rubber Boot
Carburetor to Air Box Rubber Boot. Replaces OEM # 17253-341-300 Note: 4 Boots Used Per Bike, Order Quantity you Require
Carb Fuel Line O-Ring Kit
Carb Fuel Line O-Ring 12Pc Kit Includes: 8 Carb Fuel Connector Tube O-Rings and 4 Float Bowl Drain Seal Connector Tube O-Rings (The 4 tubes that connect the 4 carbs together).
Float Bowl Drain Screw O-Rings Pk/4
Float Bowl Drain Screw O-Rings Pk/4
Air Filter Cover O-Rings Pk/2
Air Filter Cover Bolt O-Rings Pk/2, Replaces OEM# 91301-704-000
Carb Rebuild Kit
Carb Rebuild Kit Includes Items Pictured High Quality - Made In Japan 1 Kit Needed Per Carb
Performance Main Jet Kit
Performance Main Jet Kit. Kit includes a total of 16 Main Jets for Keihin Carbs. Use this jet kit to unleash the extra power you should have from your aftermarket exhaust, flee flowing air filters or any engine mods you have made. Kit includes Main Jets #105 (X4), #110 (X4), #115 (X4) and #120 (X4).
Ultimate Performance Main Jet Kit
Ultimate Performance Main Jet Kit. Kit includes a total of 44 Main Jets for Keihin Carbs. Use this jet kit to unleash the extra power you should have from your aftermarket exhaust, flee flowing air filters or any engine mods you have made. Kit includes Main Jets #100 (X4), #102 (X4), #105 (X4), #108 (X4), #110 (X4), #112 (X4), #115 (X4), #118 (X4), #120 (X4), #122 (X4) and #125 (X4)
Pilot Jet Set (Pk/4)
Stock Type Pilot Jet Set of 4 (Size #40). Pilot Jets (your idle and low speed operation) are critical for smooth idling and lower rpm driving. When rebuilding carbs it is highly recommended to replace these pilot jets to ensure your bike is running as well as possible. Fits: Honda CB750K (1972-76) with original stock carbs CB750F (1975-76) with original stock carbs Note: These Pilot Jets (#40) were the standard size equipped from the factory.
Float Needle & Seat
Float Needle & Seat High Quality - Made In Japan OEM Ref # 16011-302-004 / 16011-375-004
Float Bowl Drain Screw
Float Bowl Drain Screw w O-Ring. Note: We sell these each, order the quantity you require
Air Screw Needle O-Ring
Air Screw Needle O-Ring. 2.8mm x 1.2mm. Note: sold each, order the quantity you require
Carburetor Needle Jet Holder
Carburetor Needle Jet Holder. Replaces OEM # 16139-300-004 Note: Sold Each, One Used per Carburetor
Rear Signal Lamp Stay Screw Set/2
Rear Signal Lamp Stay Screw Set/2. This Set Includes the Screw that Fastens the Rear Signal Lamp Stays to the Rear Turn Signal Mount & Collars (#73-0127). Set includes 2 screws to fasten both rear signal stays